To Record Programmes From Satellite Receiver By Rgb Signals; Check, Change Or Delete A Programme; Linked Timer Recordings With External Equipment (Sky Digital Stb/Digital Terrestrial Receiver)-Ext Link - Panasonic Diga DMR-ES10EB Operating Instructions Manual

To record programmes from satellite
receiver by RGB signals
RAM
-R -RW(V) +R
Preparation
•
Make sure you connect the AV2 input terminal of this unit to "VCR
Scart Terminal" of a SKY Digital STB/digital terrestrial receiver with
a 21-pin scart lead (➔ page 7).
•
Set the "AV2 Input" to "RGB/Video" in the SETUP menu
(➔ page 36).
Follow the steps indicated for manually
programming timer recordings
(➔ page 20).
•
Set your Sky Digital STB to output "RGB" signals.
•
After setting the Personal Planner programmes as required, Sky
Digital STB must be kept turning on (not set to standby) to ensure
continuous output of RGB signals.

Check, change or delete a programme

RAM -R -RW(V) +R
Even when the unit is turned off, you can display the timer recording
list by pressing [PROG/CHECK].
Press [PROG/CHECK].
Icons
This programme is currently recording.
The times overlap those in another programme. Recording
W
of the programme with the later start time starts when the
earlier programme finishes recording.
The disc was full so the programme failed to record.
F
The material was copy-protected so it was not recorded.
The programme did not complete recording because the
X
disc is dirty or some other reason.
TIMER
RECORDING
No. Name Date
01 BBC 15/ 7 TUE
New Timer Programme
Message displayed in the "Disc space" line
OK: Displayed if the recording can fit in the remaining
space.
ENTER
RETURN
→ (Date):
For recordings made daily or weekly, the display
will show until when recordings can be made (up
to a maximum of one month from the present
time) based on the time remaining on the disc.
! : It may not be possible to record because:
•
the disc is write-protected
•
there is no more space left
•
the number of possible titles has reached its
maximum.
■ To change a programme
Press [e, r] to select the programme and press [ENTER].
(➔ page 20, Manually programming timer recordings, step 3)
■ To delete a programme
Press [e, r] to select the programme and press [
■ To exit the timer recording list
Press [PROG/CHECK].
■ To put the unit on timer recording standby
Press [z TIMER].
The unit turns off and "z" lights on the unit's display to indicate timer
recording standby has been activated.
•
Programmes that failed to record are deleted from the timer
recording list at 4 a.m. two days later.
Remain 1:58 SP
12:56:00 15/ 7 TUE
Disc
Start Stop Mode
PDC
space
- - -
19:00 20:00 SP OK
Cancel
CANCEL].
Linked timer recordings with external
equipment (SKY Digital STB/digital
terrestrial receiver)–EXT LINK
RAM -R -RW(V) +R
To record programmes from a SKY Digital STB/digital terrestrial
receiver using timer programming
Preparation
•
Make sure you connect the AV2 input terminal of this unit to "VCR
Scart Terminal" of a SKY Digital STB/digital terrestrial receiver with
a 21-pin scart lead (➔ page 7).
•
Set the "AV2 Input" to match the connected equipment in the
SETUP menu (➔ page 36).
•
Set the "Ext Link" to match the connected equipment in the SETUP
menu (➔ page 36).
Ext Link 1: Start and stop timings of recording are controlled by
the control signal from the SKY Digital STB/digital
terrestrial receiver using the "SKY Personal Planner"
function.
Ext Link 2: When an external equipment with a timer function
turns on, recording starts.
When it turns off, recording stops.
1
Make timer programming on SKY
Digital STB/digital terrestrial receiver.
2
Insert a disc.
3
Press [EXT LINK].
The unit turns off and "EXT Link" lights on the unit's display to
indicate timer recording standby has been activated.
Note
It is not possible to use EXT LINK function for timer recording of
RGB signals from Sky Digital STB (➔ left, To record programmes
from satellite receiver by RGB signals).
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby.
•
In order to prevent accidental operation, press [EXT LINK] to
cancel the setting after recording is finished.
For your reference
•
This function does not work with some equipment. Refer to the
equipment's operating instructions.
•
The beginnings of recordings may not be recorded correctly in
some cases.
•
When "Ext Link" is set to "Ext Link 2", this function does not work if
the input signal is NTSC system.
•
Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
RAM To divide the titles, go to "Divide Title" (➔ page 29).
•
While the unit is in EXT LINK standby mode or recording, video
picture is from the AV2 input terminal irrespective of "AV1 Output"
setting.
RQT8016
21