Bosch DS484Q Installation Instructions Manual page 11

.
4.1.2 Transmitter Setup
Figure 15: Transmitter Setup Switches
130 160
260 320
100
200
OUTDOOR
60
INDOOR
120
BEAM POWER CONTROL (m)
SWITCH
OFF ↔ ON
No ITEM OFF ON
1 Group
A B
2 SEE CHART
3 BELOW
4 NULL - -
SW2 - 3 : CHANNEL
M 1 2 3
SW2 OFF OFF ON ON
SW3 OFF ON OFF ON
MODEL:DS486Q
1 - Beam Power Control rotary switch
2 - DIP Switches 1, 2, and 3
Turn the Beam Power Control rotary switch to the
volume setting for the appropriate detection range.
Refer to Figure 15, Table 5 and Table 6.
Table 5: Settings for Outdoor Beam Power
Control
DS484Q
Volume Range
Setting m (ft)
40 0 to 40
(0 to 131)
60 40 to 60
(131 to 197)
80 60 to 80
(197 to 263)
100 80 to 100
(263 to 328)
110 100 to 110
(328 to 361)
120 110 to 120
(361 to 394)
Bosch Security Systems, Inc. | 7/05 | 4998138530F
DS484Q/DS486Q | Installation Instructions | 4.0
POWER
1
180
360
200
400
2
DS486Q
Volume Range
Setting m (ft)
60 0 to 60
(0 to 197)
100 60 to 100
(197 to 328)
130 100 to 130
(328 to 427)
160 130 to 160
(427 to 525)
180 160 to 180
(525 to 591)
200 180 to 200
(591 to 656)
Table 6: Settings for Indoor Beam Power
Control
DS484Q
Volume Range
Setting m (ft)
80 0 to 80
(0 to 263)
120 40 to 120
(263 to 394)
160 120 to 160
(394 to 525)
200 160 to 200
(525 to 656)
220 200 to 220
(656 to 722)
240 220 to 240
(722 to 787)
4.1.3 Beam Group and Channel Setup
When installing only one transmitter and
one receiver (a set), beam group and
channel selection is not required. Leave the
switches on the transmitter and receiver in
the original (OFF) positions. Refer to
Figure 17 on page 12.
The transmitter and the receiver have eight selectable
beams. The beams are divided into two groups
(Group A and Group B) of four beams each. The
beams are referred to as channels (Channels M, 1, 2,
and 3). Refer to Figure 16.
Figure 16: Beam Group and Channel
Organization
BEAM GROUP A
GROUP B
Channels 1, 2 or 3 can emit beams only when
Channel M in the same group provides those channels
with synchronized (synchro) wiring. Refer to Section
4.1.4 Synchronized Wiring on page 12. When installing
two or more sets in the same group, set only the first
set to Channel M. Set the remaining sets to Channel 1,
2, or 3.
Setup and Alignment
DS486Q
Volume Range
Setting m (ft)
120 0 to 120
(0 to 394)
200 120 to 200
(394 to 656)
260 200 to 260
(656 to 853)
320 260 to 320
(853 to 1050)
360 320 to 360
(1050 to 1181)
400 360 to 400
(1181 to 1312)
CHANNEL M
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL M
CHANNEL 1
CHANNEL 2
CHANNEL 3
11