Clarion WXZ468RMP Service Manual page 22

pin 38: Po 9 : O : General-purpose output terminal.
pin 39: Po 8 : O : General-purpose output terminal.
pin 40: VDDM : - : Positive voltage supply.
pin 41: SRMSTB : IN : Internal SRAM I/F. Standby input.
pin 42: VDDT : - : Positive voltage supply.
pin 43: AD 10 : O : SRAM/FRAM I/F. Address output.
pin 44: AD 9 : O : SRAM/FRAM I/F. Address output.
pin 45: AD 8 : O : SRAM/FRAM I/F. Address output.
pin 46: AD 7 : O : SRAM/FRAM I/F. Address output.
pin 47: AD 6 : O : SRAM/FRAM I/F. Address output.
pin 48: AD 5 : O : SRAM/FRAM I/F. Address output.
pin 49: AD 4 : O : SRAM/FRAM I/F. Address output.
pin 50: AD 3 : O : SRAM/FRAM I/F. Address output.
pin 51: AD 2 : O : SRAM/FRAM I/F. Address output.
pin 52: AD 1 : O : SRAM/FRAM I/F. Address output.
pin 53: AD 0 : O : SRAM/FRAM I/F. Address output.
pin 54: VSS : - : Ground.
pin 55: VDD : - : Positive voltage supply.
pin 56: CKo : O : Clock output.
: Po 13 : O : General-purpose output terminal.
pin 57: VDDX : - : Positive voltage supply.
pin 58: Xo : O : Crystal connection.
pin 59: Xi : IN : Crystal connection.
pin 60: VSSX : - : Ground.
pin 61: TEST : IN : H = Test.
pin 62: MiMD : IN : H = I2C, L = Normal.
pin 63: VSSP : - : Ground.
pin 64: VCOi : O : Control voltage output for VCO.
051-9318-10 GLT4160L04P-60TC
Terminal Description
pin 1 : VCC : Positive supply voltage.
pin 2 : DQ 0 : Data input / output.
pin 3 : DQ 1 : Data input / output.
pin 4 : WE_ : Write enable.
pin 5 : RAS_ : Row address strobe.
pin 6 : NU : Not in use.
pin 7 : NEX : No existence.
pin 8 : A 10 : Address input.
pin 9 : A 0 : Address input.
pin 10: A 1 : Address input.
pin 11: A 2 : Address input.
pin 12: A 3 : Address input.
pin 13: VCC : Positive supply voltage.
pin 14: VSS : Ground.
pin 15: A 4 : Address input.
pin 16: A 5 : Address input.
pin 17: A 6 : Address input.
pin 18: A 7 : Address input.
pin 19: A 8 : Address input.
pin 20: NEX : No existence.
pin 21: A 9 : Address input.
pin 22: OE_ : Output enable.
pin 23: CAS_ : Column address strobe.
pin 24: DQ 2 : Data input / output.
pin 25: DQ 3 : Data input / output.
pin 26: VSS : Ground.
929-0371-80
16M bit Dynamic RAM
- M2-
052-5070-91 T5AF4
TerminalDescription
pin 1: Vref L : - : Reference voltage.
pin 2: A VSS : - : Negative voltage supply for analog section.
pin 3: A VCC : - : Positive voltage supply for the internal
analog section.
pin 4: LO CW : O : Loading motor control signal output.
pin 5: LO CCW : O : Loading motor control signal output.
pin 6: A MUTE : O : The audio mute signal output.
pin 7: De-emphasis : IN : De-emphasis ON command input.
pin 8: E-EJ : IN : Emergency Eject input.
pin 9: P ON 1 : O : Power ON signal output.
pin 10: NU : - : Not in use.
pin 11: P ON 3 : O : Power ON signal output.
pin 12: NU : - : Not in use.
pin 13: NU : - : Not in use.
pin 14: NU : - : Not in use.
pin 15: NU : - : Not in use.
pin 16: NU : - : Not in use.
pin 17: NU : - : Not in use.
pin 18: DSP SO : O : Serial data output to the DSP IC.
pin 19: DSP SI : IN : Serial data input from the DSP IC.
pin 20: DSP SCK : O : The clock pulse output to DSP IC.
pin 21: FL TX : O : The serial data output for flash memory.
pin 22: FL RX : IN : The serial data input for flash memory.
pin 23: SW 9V : O : 9V power supply control.
pin 24: PULL UP : IN : PULL UP
pin 25: VCC : - : Positive voltage supply.
pin 26: X out : O : Crystal connection.
pin 27: VSS : - : Negative voltage supply.
pin 28: X in : IN : Crystal connection.
pin 29: PULL UP : IN : PULL UP
pin 30: RESET : IN : Reset signal input.
pin 31: TIME : O : For Time base.
pin 32: NU : - : Not in use.
pin 33: NC : O : Not in use.
pin 34: NC : O : Not in use.
pin 35: BU DET : IN : Backup detection signal input.
pin 36: SW 5 : IN : The switch signal input.
pin 37: SBSY : IN : Sub code block synchronous signal detec-
tion input.
pin 38: PON 2 : O : Power ON signal output.
pin 39: MODE CW : O : Mode motor control.
pin 40: MODE CCW : O : Mode motor control.
pin 41: U/D CW : O : Holder control.
pin 42: U/D CCW : O : Holder control.
pin 43: ALE : O : The address latch enable output.
pin 44: DR MUTE : O : Drive mute signal output to the CD IC.
pin 45: SRAM STNDB : O : SRAM standby signal output.
pin 46: DSP RESET : O : Reset signal output to the DSP IC.
pin 47: DSP CS : O : Chip select signal output to the DSP.
pin 48: DSP LAT : O : The latch pulse output to DSP IC.
pin 49: DSP ACK : IN : DSP acknowledge.
pin 50: LIMIT : IN : Inside limit switch signal input.
pin 51: EEP CS : O : The chip select output to EEP-ROM.
pin 52: EEP SK : O : The clock pulse output to the EEP-ROM.
pin 53: EEP DI : IN : The serial data input from the EEP-ROM.
pin 54: EEP DO : O : The serial data output to the EEP-ROM.
pin 55: HSSW : IN : It is used at the jitter measurement (the
speed is 2X, shock proof is through).
pin 56: HSSW 2 : IN : It is used at the jitter measurement (the
speed is 1X, shock proof is through).
pin 57: DSP REQ : IN : DSP request input.
pin 58: DSP STNDB : O : DSP standby output.
pin 59: NU : - : Not in use.
pin 60: NU : - : Not in use.
pin 61: BUC CLOCK : O : CD IC clock pulse output.
pin 62: VSS : - : Negative voltage supply.
pin 63: NMI : IN : Connect to VDD via a resistor.
pin 64: VCC : - : Positive voltage supply.
Mechanism Controller