Kenwood VRS-7200 Instruction Manual page 19

Preparing for playback
5
Select a speaker system.
1 Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate subwoofer setting.
1 "SUBW ON" :
When a subwoofer is connected.
2 "SUBW OFF" :
When no subwoofer is connected.
÷ The initial setting is "SUBW ON".
÷ When "SUBW OFF" is selected and the selection is estab-
lished by pressing the MULTI CONTROL # (or the # key) in
step 2 below, the front speakers are set automatically to
"FRNT LRG" and the procedure jumps to step 5.
2 Use the MULTI CONTROL # (or the # key) to ac-
cept the setting.
÷ The front speakers setting indication "FRNT" appears.
3 Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate front speakers setting.
1 "FRNT LRG" :
Large front speakers are connected to the receiver.
2 "FRNT NML" :
Average size front speakers are connected to the
receiver.
÷ When the subwoofer setting is "SUBW ON", front speak-
ers setting is "FRNT LRG" and a stereo source is played,
the low frequencies may be reproduced through the
front speakers and no audio output from the subwoofer
in certain listen modes. In this case, set the subwoofer
re-mix setting in step # to "REMIX ON" to output the
low frequencies from the subwoofer.
4 Use the MULTI CONTROL # (or the # key) to ac-
cept the setting.
÷ The center speaker setting indication "CNTR" appears.
5 Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate center speaker setting.
1 "CNTR LRG" :
A large center speaker is connected to the receiver.
2 "CNTR NML" :
An average size center speaker is connected to the
receiver.
3 "CNTR OFF" :
When no center speaker is connected.
*
"CNTR LRG" cannot be selected when the front
speakers have been set to "FRNT NML".
6 Use the MULTI CONTROL # (or the # key) to ac-
cept the setting.
÷ The surround speaker setting indication "SURR" appears.
*
7 Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate surround speaker setting.
*
1 "SURR LRG" :
Large surround speakers are connected to the receiver.
2 "SURR NML" :
Average size surround speakers are connected to the
receiver.
3 "SURR OFF" :
When no surround speakers are connected.
*
"SURR LRG" cannot be selected when the front speakers
have been set to "FRNT NML".
÷ When "SURR OFF" is selected and the selection is estab-
lished by pressing the MULTI CONTROL # in step 8 below,
the procedure jumps to step #. However, if the subwoofer
setting is "SUBW OFF", the procedure jumps to step $ so
that you can complete the speaker setup and proceed to the
speaker volume level adjustment in step 6.
8 Use the MULTI CONTROL # (or # key) to accept
the setting.
÷ The surround back speaker setting indication "BS" appears.
9 Use the MULTI CONTROL % / fi (or the % / fi keys) to
select appropriate surround back speaker setting.
*
1 "BS LRG" :
Large surround back speaker is connected to the re-
ceiver.
2 "BS NML" :
Average size surround back speaker is connected to the
receiver.
3 "BS OFF" :
When no surround back speakers is connected.
*
"BS LRG" cannot be selected when the surround
speaker have been set to "SURR NML".
0 Use the MULTI CONTROL # (or the # key) to accept
the setting.
÷ The surround back speaker and subwoofer setting mode
indication "BS/SW" appears.
Continued to next page
19
EN