RAMSET RAM-1000 UL Instruction Manual

RAMSET RAM-1000 UL Instruction Manual

For class i, ii, iii, iv vehicular gate operators
Hide thumbs Also See for RAM-1000 UL:

Advertisement

©
Instruction Manual
®
Model RAM-1000 UL & RAM-5500 UL
C
US
For Class I, II, III, IV Vehicular Gate Operators
Rev 060202
No. 545327

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RAM-1000 UL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RAMSET RAM-1000 UL

  • Page 1 © ™ Instruction Manual ® Model RAM-1000 UL & RAM-5500 UL For Class I, II, III, IV Vehicular Gate Operators Rev 060202 No. 545327...
  • Page 2: Table Of Contents

    RAM-1000 UL Parts Diagram ........
  • Page 3 Installation should be done by a qualified installer only. Prior to Installation, the following must be For Vehicular Gate Operators utilizing a non- observed: (per UL 325 51.8.4) contact sensor in accordance with 30A.1.1 Type B1 non-contact sensor (photo electric Install the vehicular gate operator only when: sensor or the equivalent) 1) The Vehicular Gate Operator is appropri-...
  • Page 4: Mechanical Specifications

    MECHANICAL SPECIFICATIONS: Model: RAM-1000 UL RAM-5500 UL Power Input: 120VAC 120VAC Continuous Duty 1/2 HP, 120VAC, 4.5 A, 1,625 RPM with High 3/4 HP, 120VAC, 8.5 A, 1,625 RPM with High Motor: Speed Bearings Speed Bearings Aerovox 65µƒ, 240 V, 50/60 HZ, protected S Aerovox 65µƒ, 240 V, 50/60 HZ, protected S...
  • Page 5: Installation Specifications

    “A” “C” UNC Red-head Anchor Bolts 18” concrete MODEL Dim "A" Dim "B" Dim "C" Dim "D" Dim "E" RAM-1000 UL 13-3/4" 8-1/2" 2-1/8" 14" 8-1/2" RAM-5500 UL 13.902 8.625 or 6.625 2.049 13.875 R A M S E T...
  • Page 6: Recommended Wire Gauge / Voltage Drop Chart

    Figure 4 6” min. Dim “D” minus 24” Concrete Pad Rear Installation distance deter- mined by pulleys Gate Shown Fully Open No tail on gate required 18” x 18” 6” min. 2-1/2” diameter UHMW Pulley Center Installation Concrete Pad Gate Shown Fully Open No tail on gate required Figure 5 Low voltage control wires must be run in a separate conduit to the operator.
  • Page 7: Gate Travel Adjustment

    GATE TRAVEL ADJUSTMENT To adjust gate travel, depress spring loaded bracket and spin each Adjustment Nut to the required position (Figure 6). LED must turn on to indicate position open or close when limit switch is activated by limit switch adjustment nut. Figure 6 Limit Switches Adjustment...
  • Page 8: Electrical Connection

    ELECTRICAL CONNECTION A 3 wire, 120VAC electrical circuit with a 15 amp independent circuit breaker is required for each oper- ator. Ideally, the electrical conduits should exit the concrete under the operator. Low voltage control wires must be run in a separate conduit to the operator as shown. Intelligate ©...
  • Page 9: Introduction

    Used with a three button switch or a pedestrian entranceto stop INTRODUCTION the gate. DIP FUNCTION Ramset’s “Intelligate” Control board is for operating a vehicular ‘off’ normal operation gate operator. The control board is available for either 110VAC ‘on’ normally closed contact. With an open contact the board or 220VAC, single phase, applications.
  • Page 10: Terminal Strip Connections

    DIP SWITCH B5: “LAG DELAY” SAFETY INPUT DESCRIPTION Note: if both B5 & Lag on Close B6 are 'on', there One second lag on close Limit 1 & Limit 2 – Depending on dip switch B7 (see “dip will be NO lag on switch features”), stops the motor from moving in one direc- the open or close.
  • Page 11: Wiring Diagram

    CAUTION Electronic Control Board must be serviced by a certified technician only. Power must be turned OFF before servicing operator. Power must be turned OFF before attempting to adjust the limit switches. Power must be turned OFF for power failure release. WIRING DIAGRAM Figure 10 NEUTRAL...
  • Page 12: Sensor Installation

    SENSOR INSTALLATION Reversing Sensors on the ground floor prevent WARNING gate from closing when vehicle is in loop area. A non-contact sensor (photoelectric sensor or Exit Loops on the ground floor opens gate equivalent) and a contact sensor (edge device or when vehicle crosses loop area.
  • Page 13: Bill Of Materials

    BILL OF MATERIAL FOR RAM-1000 UL AND RAM-5500 UL ITEM PART # PART DESCRIPTION RAM-1000 UL RAM-5500 UL 50-031 1/2 hp 115 vac electric motor 50-039 20 pin edge connector 50-058 3 1/2" uhmw idler pulley 50-069 limit switch 00-h3...
  • Page 14: Ram-1000 Ul Parts Diagram

    RAM-1000 UL PARTS DIAGRAM Figure 13 R A M S E T R A M S E T R A M S E T - 13 -...
  • Page 15: Ram-5500 Ul Parts Diagram

    RAM-5500 UL PARTS DIAGRAM Figure 14 R A M S E T R A M S E T R A M S E T - 14 -...
  • Page 16: Glossary

    O U R W E B S I T E W W W . R A M S E T I N C . C O M Ramset Automatic Gate Systems (800) 771-7055 9116 De Garmo Ave. Sun Valley, CA. 91352...

Table of Contents

Save PDF