Kenwood NX-820H Service Manual page 47

Item Panel test mode
2.High Transmit 1) Adj item:
Power [HPWR]
Adjust:[]
2) Adj item:
[H.PWR_] →
[H.P.WR_] →
[H.P.W.R_] →
[H.P.W.R._] →
[H.P.W.R._.] →
3) PTT : ON
4) Press [ ] key to
store the adjust-
ment value
Mid Transmit 1) Adj item:
power [MPWR]
Adjust:[]
2) Adj item:
[M.PWR_] →
[M.P.WR_] →
[M.P.W.R_] →
[M.P.W.R._] →
[M.P.W.R._.] →
3) PTT : ON
4) Press [ ] key to
store the adjust-
ment value
Low Transmit 1) Adj item:
power [LPWR]
Adjust:[]
2) Adj item:
[L.PWR_] →
[L.P.WR_] →
[L.P.W.R_] →
[L.P.W.R._] →
[L.P.W.R._.] →
3) PTT : ON
4) Press [ ] key to
store the adjust-
ment value
3. Balance 1) Adj item:[BAL]
adjust Adjust:[]
Deviation meter
LPF : 3kHz
HPF : OFF
2) Adj item:
[B.AL_]
[B.A.L__]
[B.A.L.__]
[B.A.L._._]
[B.A.L._._.]
Adjust:[]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
ADJUSTMENT
Measurement
PC test mode
Test-
equipment
1) TEST CH: Power
Low, Low', Center, meter
High', High (5 point) Ammeter
2) Transmit
Press [Apply All]
button to store the
adjustment value.
1) TEST CH:
Low, Low', Center,
High', High (5 point)
2) Transmit
Press [Apply All]
button to store the
adjustment value.
1) TEST CH:
Low, Low', Center,
High', High (5 point)
2) Transmit
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Balance] Deviation
Deviation meter meter
LPF : 3kHz Oscillo-
HPF : OFF scope
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
PTT: Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
[2kHz Sine Wave
Check box]: Check
while transmitting
change to 2kHz.
NX-820H(G)/820H
Adjustment
Termi-
Unit Unit Parts
nal
ANT [Panel
tuning
mode]
[ ],[ ]
[PC test
mode]
[ ],[ ]
ANT [Panel
tuning
mode]
[ ],[ ]
[PC test
mode]
[ ],[ ]
Specifi cations/
Remarks
Method
45.0W ±1.0W
13.0A or less
[PC test mode]
Press [Apply All]
button to store the
adjustment value
after all adjust-
ment point was
adjusted.
30.0W ±1.0W
10.0A or less
[PC test mode]
Press [Apply All]
button to store the
adjustment value
after all adjust-
ment point was
adjusted.
5.0W ±0.2W
7.0A or less
[PC test mode]
Press [Apply All]
button to store the
adjustment value
after all adjust-
ment point was
adjusted.
The Deviation of 2kHz Tone de-
20Hz frequency is viation is within
fi xed. Change the ±1.0% of 20Hz
2kHz adjustment tone deviation.
value to become
the same deviation [PC test mode]
of 20Hz within the Press [Apply All]
specifi ed range. button to store the
adjustment value
after all adjust-
ment point was
adjusted.
47