Page 1 2 0 0 7 OW N E R ’ S M A N UA L...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....7 ▫...
Page 5: Introduction
4 INTRODUCTION INTRODUCTION Roll Over Warning This manual has been prepared with the assistance of Utility vehicles have a significantly higher roll over rate service and engineering specialists to acquaint you with than other types of vehicles. This vehicle has a higher the operation and maintenance of your new vehicle.
Page 6: How To Use This Manual
INTRODUCTION 5 belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually. In a roll over crash an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 7 6 INTRODUCTION...
Page 8: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Steering Wheel Lock — Manual Transmission Only ....... . .17 ▫...
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ “Child-Protection” Door Lock System (Rear Doors) ▫ Security System Manual Override ...32 — If Equipped ......23 Liftgate .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Extender ..... .48 Safety Tips ......69 ▫...
Page 13: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The dealer that sold you your new vehicle has the key Automatic Transaxle code numbers for your vehicle locks. These numbers can Place the shift lever in PARK. Turn the ignition switch to be used to order duplicate keys from your dealer.
Page 14: Locking Doors With The Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the CAUTION! lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the An unlocked car is an invitation to thieves.
Page 15: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder unlocked. During normal operation, the Theft Alarm/ Opening the driver’s door when the key is in the ignition, Immobilizer Light will come on for three (3) seconds sounds a signal to remind you to remove the key. immediately after the ignition switch is turned on for a bulb check.
Page 16: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: Replacement Keys • The Sentry Key Immobilizer System is not compatible NOTE: Only keys that have been programmed to the with remote starting systems. Use of these systems vehicle electronics can be used to start the vehicle. Once may result in vehicle starting problems and loss of a Sentry Key has been programmed to a vehicle, it cannot security protection.
Page 17: Sentry Key Programming
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sentry Key Programming The new Sentry Key has been programmed. You can program new keys to the system if you have two Repeat this procedure to program up to 8 keys. If you do valid sentry keys by performing the following procedure: not have a programmed sentry key, contact your dealer 1.
Page 18: Steering Wheel Lock - Manual Transmission Only
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 STEERING WHEEL LOCK — Manual To Release The Steering Wheel Lock: Transmission Only Insert the key in the ignition switch and start the engine. Your manual transmission vehicle is equipped with a If the key is difficult to turn, move the wheel slightly to passive steering wheel lock.
Page 19: Door Locks
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks For personal security, and safety in the event of an Use the manual door lock plunger to lock the doors from accident, lock the vehicle doors as you drive as well inside the vehicle.
Page 20: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver door panel. Press this switch to lock or unlock the doors.
Page 21 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h). 6. The doors were not previously locked using the power door lock switch or remote keyless entry transmitter. The Automatic Door Lock feature can be enabled or disabled.
Page 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3.
Page 23 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Auto Unlock feature can be enabled or disabled. Refer to “Personal Settings” (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) — if equipped section of this manual. For vehicles not equipped with the EVIC the Auto Unlock Feature can be enabled or disabled by performing the following procedure: 1.
Page 24: Things To Know Before Starting Your Vehicle 23
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws. “Child-Protection” Door Lock System (Rear Doors) — If Equipped Insert the tip of the ignition key into the lock and rotate to the lock or unlock position.
Page 25: Remote Keyless Entry - If Equipped
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 26: To Unlock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: The line of transmission must not be blocked under “Personal Settings” in the EVIC section of this with metal objects. manual. On non EVIC – equipped vehicles perform the following steps: To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob The system can be programmed to unlock all the doors...
Page 27: To Lock The Doors And Liftgate
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while 2. While the LOCK button is pressed (after 4 seconds), you are inside the vehicle will activate the Security press the PANIC button. Release both buttons. Alarm.
Page 28: To Turn Off "Flash Lights With Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: When you turn off the panic alarm by pressing NOTE: Pressing the LOCK button on the key fob, while the PANIC button a second time, you may have to be you are in the vehicle, will activate the Security Alarm. closer to the vehicle due to the radio frequency noises of Opening a door with the Security Alarm activated will the system.
Page 29 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Use the Following procedure to program additional key program mode. All fobs that are to be programmed must fobs if the vehicle is not equipped with Sentry Key: be done so within 60 seconds of when the chime was heard.
Page 30: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 NOTE: If you do not have a programmed transmitter, If your Remote Lock Control fails to operate from a contact your dealer for details. normal distance, check for these two conditions. General Information 1.
Page 31: Security Alarm System - If Equipped
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. If the key fob is equipped with a screw, remove the 2. Remove and replace the batteries. Avoid touching the screw. With the transmitter buttons facing down, use a new batteries with your fingers. Skin oils may cause flat blade to pry the two halves of the transmitter apart.
Page 32: To Set The Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 If the monitored system, which triggered the alarm is disarm. After 16 seconds the indicator light will flash deactivated the alarm will continue to sound until 3 slowly. This shows that the system is fully armed. minutes of alarm time is reached.
Page 33: Security System Manual Override
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security System Manual Override LIFTGATE The system will not arm if you lock the doors using the NOTE: The key that is used to start the vehicle is also manual door lock plunger. used to lock or unlock the doors and open the liftgate.
Page 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: Although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. WARNING! •...
Page 35: Power Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. POWER WINDOWS However, because the gas pressure drops with tempera- Power Window Switches ture, it may be necessary to assist the props when opening the liftgate in cold weather.
Page 36: Auto Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 passenger doors for passenger window control. The windows will operate only when the ignition switch is turned to the ON position and for 45 seconds after the ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer.
Page 37: Window Lockout Switch
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch OCCUPANT RESTRAINTS The window lockout switch on the driver’s door allows Some of the most important safety features in your you to disable the window control on the other doors. To vehicle are the restraint systems.
Page 38: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 of the worst injuries happen when people are thrown WARNING! from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the In a collision, you and your passengers can suffer inside of the vehicle.
Page 39: Instructions
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, • Wearing a seat belt incorrectly is dangerous. Seat inside or outside of a vehicle. In a collision, people belts are designed to go around the large bones of riding in these areas are more likely to be seri- your body.
Page 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, •...
Page 43: Adjustable Upper Shoulder Belt Anchorage
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Adjustable Upper Shoulder Belt Anchorage The belt will automatically retract to its stowed position. In the front seat, the shoulder belt can be adjusted If necessary, slide the latch plate down the webbing to upward or downward to position the belt away from allow the belt to retract fully.
Page 44: Second Row Center Lap/Shoulder Belt Operating Instructions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the shoulder belt to the inside of the right head restraint. Routing The Rear Center Shoulder Belt 4. When the belt is long enough to fit, insert the mini latch plate into the mini buckle until you hear a “click.” Routing The Rear Center Shoulder Belt 5.
Page 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 6. When the belt is long enough to fit, insert the latch on the shoulder belt. To loosen the lap belt if it is too tight, plate into the buckle until you hear a “click.” pull on the lap belt.
Page 47: Seat Belt Pretensioners
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. To release the belt, push the red button on the buckle. slide the latch plate down the webbing to allow the belt to retract fully. Insert the mini latch plate into the slot provided in the trim panel.
Page 48: Enhanced Driver Seat Belt Reminder System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 items. After a collision that is severe enough to deploy The Enhanced Warning System (BeltAlert) can be en- the airbags and pretensioners, both must be replaced. abled or disabled by your authorized dealer or by following these steps: Enhanced Driver Seat Belt Reminder System NOTE: The following steps must occur within the first...
Page 49: Seat Belt Extender
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Warning Light to turn on equipped) is in its lowest position, your dealer can while unbuckling and off while re-buckling the seat belt. provide you with a seat belt extender. This extender It may be necessary to retract the seat belt.
Page 50: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 51 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity.
Page 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 NOTE: Do not use a clothing bar mounted to the coat WARNING! hooks in this vehicle. A clothing bar will impede the proper performance of the curtain airbags. • Do not put anything on or around the front airbag covers or attempt to manually open them.
Page 53 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize 5. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the the risk of harm from a deploying airbag.
Page 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Air Bag System Components WARNING! The airbag system consists of the following: • Relying on the airbags alone could lead to more • Occupant Restraint Controller (ORC) severe injuries in a collision. The airbags work •...
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Acceleration Sensors • The ORC also turns on the Airbag Warning Light in the instrument panel for 6 to 8 • Driver and Front Passenger Seat Belt Pretensioners seconds as a self-check when the ignition is How The Airbag System Works first turned on.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • The Driver and Front Passenger Airbag/Inflator • The Side Impact SRS Side Curtain Airbag are de- Units are located in the center of the steering wheel signed to activate only in certain side collisions. When and the passenger side of the instrument panel.
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs However, if you haven’t healed significantly within a The airbag system is designed to deploy when the ORC few days, or if you have any blistering, see your doctor detects a moderate-to-severe collision, to help restrain the immediately.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Maintaining Your Airbag System WARNING! WARNING! Deployed airbags can’t protect you in another colli- • Modifications to any part of the airbag system sion. Have the airbags replaced by an authorized dealer as soon as possible. could cause it to fail when you need it.
Page 59: Event Data Recorder (Edr)
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light Event Data Recorder (EDR) You will want to have the airbags ready to In the event of an accident, your vehicle is designed to inflate for your protection in an impact. While record up to 5 - seconds of specific vehicle data param- the airbag system is designed to be mainte- eters (see list below) in an event data recorder prior to the...
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 In conjunction with other data gathered during a com- custodial entity upon request. General data that does not plete accident investigation, the electronic data may be identify particular vehicles or crashes may be released for used by DaimlerChrysler and others to learn more about incorporation in aggregate crash databases, such as those the possible causes of crashes and associated injuries in...
Page 61: Child Restraint
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status • Traction/stability control status for electronically-controlled safety systems, including • Tire pressure monitoring system status the airbag system Child Restraint •...
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • Safety experts recommend that children ride WARNING! rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types In a collision, an unrestrained child, even a tiny baby, of child restraints can be used rearward-facing: infant can become a missile inside the vehicle.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in seat are held in the vehicle by the lap/shoulder belt. the front seat of a vehicle with a front passenger (Some booster seats are equipped with a front shield airbag.
Page 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Here are some tips on getting the most out of your child restraint so that it is not necessary to use a locking clip. restraint: If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will •...
Page 65 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if by pulling and from the retractor. Allow the belt to return into the pushing on the restraint loosens the belt, disconnect retractor, pulling on the excess webbing to tighten the lap the latch plate from the buckle, turn the latch plate portion about the child restraint.
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older restraint installation, instead of tucking the seat belt products. Tether anchorage kits are also available for behind the child restraint, route the seat belt through the most older vehicles.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back.
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or WARNING! slouching can move the belt out of position. An incorrectly anchored tether strap could lead to • If the shoulder belt contacts the face or neck, move the increased head motion and possible injury to the child closer to the center of the vehicle.
Page 70: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 A new engine may consume some oil during its first few ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in thousand miles (kilometers) of operation. This should be your new vehicle.
Page 71: Safety Checks You Should Make Inside The Vehicle
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined Safety Checks You Should Make Inside The areas any longer than needed to move your vehicle in or Vehicle out of the area. Seat Belts If it is necessary to sit in a parked vehicle with the engine Inspect the belt system periodically, checking for cuts,...
Page 72: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to while you work the controls. Check turn signal and high feel the air directed against the windshield.
Page 74: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......78 Hands–Free Communication (UConnect™) — If Equipped .
Page 75 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Front Seat Adjustment ....108 ▫ Multi-Function Control Lever ... . . 119 ▫...
Page 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 ▫ Windshield Wiper Operation ... . . 125 ▫ Programming The Universal Transceiver ..131 ▫ Intermittent Wiper System ....125 ▫...
Page 77 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Hill Descent Control (HDC) – If Equipped . . . 140 ▫ Ignition Off Operation ....149 ▫...
Page 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Rear Window Defroster ....159 Roof Luggage Rack — If Equipped ..160...
Page 79: Mirrors
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 80: Outside Mirror-Passenger's Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
Page 81: Folding Outside Mirrors - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Outside Mirrors — If Equipped Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. Folding the Outside Mirrors The exterior mirrors are hinged and may be moved, Remote Control Mirrors Switch manually, either forward or rearward to resist damage.
Page 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object.
Page 83: Vanity Mirrors - If Equipped
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors — If Equipped Sun Visor Sliding Feature To use the mirror, rotate the sun visor down and swing The sun visors may be pulled out to provide extended the mirror cover upward. coverage of the side glass.
Page 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 UConnect™ allows you to transfer calls between the with the system at a time. The system is available in system and your cellular phone as you enter or exit your English, Spanish, or French languages (as equipped). vehicle, and enables you to mute the system’s micro- The rearview mirror contains the microphone for the phone for private conversation.
Page 85: Operations
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any Hands- Operations Free Profile certified Bluetooth™ cellular phone. See Voice commands can be used to operate the UConnect™ www.chrysler.com/uconnect for supported phones. If system and to navigate through the UConnect™ menu your cellular phone supports a different profile (e.g., structure.
Page 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 example, you can use the combined form voice com- Cancel Command mand Phonebook New Entry, or you can break the At any prompt, after the voice on beep, you can say combined form command into two voice commands: Cancel and you will be returned to the main menu.
Page 87 Each cellular phone that is paired should be • www.dodge.com/uconnect given a unique phone name. • www.jeep.com/uconnect • You will then be asked to give your cellular phone a The following are general phone to UConnect™ System priority level between 1 and 7, 1 being the highest pairing instructions: priority.
Page 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Call/Dial by Saying a Number Call/Dial by Saying a Name • Press the ’Phone’ button to begin. • Press the “Phone” button to begin. • After the Ready prompt and the following beep, say •...
Page 89 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook After you are finished adding an entry into the phone- book, you will be given the opportunity to add more NOTE: Adding names to phonebook is recommended phone numbers to the current entry or to return to the when vehicle is not in motion.
Page 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • You will then be asked for the name of the phonebook Delete Entries in the UConnect™ Phonebook entry that you wish to edit. NOTE: Editing phonebook entries is recommended • Next, choose the number designation (home, work, when vehicle is not in motion.
Page 91 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect™ system will • After confirmation, the phonebook entries will be ask you which designation you wish to delete, home, deleted. work, mobile, or pager. Say the designation you wish List All Names in the UConnect™...
Page 92: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Answer or Reject an Incoming Call - Call Phone Call Features The following features can be accessed through the Currently in Progress UConnect™ system if the feature(s) are available on your If a call is currently in progress and you have another cellular service plan.
Page 93 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE second call is in progress. To go back to the first call, refer Conference Call to Toggling Between Calls. To combine two calls, refer When two calls are in progress (one active and one on to Conference Call.
Page 94: Uconnect™ System Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • After ignition key is switched off, a call can continue hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press on the UConnect™ system either until the call ends or and hold the ‘Phone’...
Page 95 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say • Pick up the phone and manually dial the emergency the name of the language you wish to switch to number for your area. (English, Espanol, or Francais, if so equipped).
Page 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Your phone must be turned on and paired to the UCon- Paging nect™ system to allow use of this vehicle feature in To learn how to page, refer to Working with Automated emergency situations when the cell phone has network Systems.
Page 97 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system Turning Confirmation Prompts On/Off that normally requires you to enter in a touch-tone Turning confirmation prompts off will stop the system sequence on your cellular phone keypad, you can push from confirming your choices (e.g., the UConnect™...
Page 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Dialing Using the Cellular Phone Keypad Mute/Un-mute (Mute off) You can dial a phone number with your cellular phone When you mute the UConnect™ system, you will still be keypad and still use the UConnect™ system (while able to hear the conversation coming from the other dialing via the cell phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 99: Advanced Phone Connectivity
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service If you would like to connect or disconnect the Blue- When using AT&T Wireless Service, dialing to phone tooth™ connection between a UConnect™ paired cellular number #121, you can access voice activated automated phone and the UConnect™...
Page 100: Things You Should Know About Your Uconnect™ System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Select another Cellular Phone Delete UConnect™ Paired Cellular Phones This feature allows you to select and start using another • Press the ’Phone’ button to begin. phone with the UConnect™ system. The phone must •...
Page 101 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE training mode, follow one of the two procedures: From Voice Recognition (VR) outside the UConnect mode (e.g. from radio mode), • Always wait for the beep before speaking. • Press and hold the ‘Voice Recognition’ button for 5 •...
Page 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • In a convertible vehicle, the system performance may • You can say O (letter O ) for 0 (zero). 800 must be be compromised with roof top down. spoken eight-zero-zero. • Even though the system is designed for users speaking •...
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, the system performance may switching the phone off/on. Your cell phone is recom- be compromised with roof top down. mended to remain in Bluetooth on mode. • Performance, such as audio clarity, echo, and loudness Power-Up to a large degree rely on the phone and network, and After switching the ignition key from OFF to either ON...
Page 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103...
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105...
Page 107 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Call Primary Alternate(s) Cancel Zero Confirmation Prompts Continue Delete Three Dial Four Edit Five Emergency English Seven Erase All Eight Espanol Nine Francais Star (*) Help Plus (+) Home Pound (#) Language Add Location List names...
Page 108: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Mobile Towing assistance Mute Transfer call Mute off Try again New entry Voice training Work Pager Pair a phone General Information Phone pairing Pairing This device complies with part 15 of the FCC rules and Phonebook Phone book RSS 210 of Industry Canada.
Page 109: Seats
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. Front Seat Adjustment The adjusting bar is at the front of the seats, near the WARNING! floor.
Page 110: Manual Seat Height Adjustment - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Manual Seat Height Adjustment — If Equipped Manual Lumbar— If Equipped The driver’s seat height can be raised or lowered by using The Lumbar adjustment is located on the outboard side the ratcheting handle on the outboard side of the seat to of the driver’s seat.
Page 111: Driver's Seat Back Recline
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Seat Back Recline Adjustable Head Restraints To recline: Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down 1. Lean forward before lifting the handle, then lean back on the head restraints so that the upper edge is as high as to the desired position and release the handle.
Page 112: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 113 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Pressing the switch a second time will select low-level This feature heats the front driver’s and passenger’s seats. The controls for the heater is located on the heating. Pressing the switch a third time will shut the instrument panel, below the radio.
Page 114: Fold Flat Front Passenger Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Fold Flat Front Passenger Seat Front Passenger Seat Folded Flat Fold Flat Front Passenger Seat Control...
Page 115: Folding Rear Seat
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to move the seat forward and flat. Rear Seat Folded Flat Folding Rear Seat...
Page 116: Reclining Rear Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Reclining Rear Seat — If Equipped Rear Seat Recline Pull Reclining The Rear Seat...
Page 117: To Open And Close The Hood
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional comfort, pull the strap forward just TO OPEN AND CLOSE THE HOOD enough to release the seatback latch. Then push the To open the hood, two latches must be released. First pull seatback to a reclined position, approximately 35 degrees the hood release lever located on the left kick panel.
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Then move the safety catch located under the front edge To prevent possible damage, do not slam the hood to of the hood, near the center and raise the hood. close it. Lower the hood until it is open approximately 20 cm (8 inches) and then drop it.
Page 119: Lights
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Map/Reading Lights These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn the light OFF.
Page 120: Multi-Function Control Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Multi-Function Control Lever The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column.
Page 121: Lights-On Reminder
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, Lights-on Reminder rotate the center portion of the Multi-Function Control If the headlights or parking lights are on after the ignition Lever up or down. is turned OFF, a chime will sound to alert the driver when the driver’s door is opened.
Page 122: Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 NOTE: The fog lights will only operate with the head- Fog Lights — If Equipped lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Front Fog Lights Control The front fog light switch is on the Multi-Function Control Lever.
Page 123: Highbeam/Lowbeam Select Switch
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE show proper operation of the front and rear turn signal Highbeam/Lowbeam Select Switch lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
Page 124: Passing Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Passing Light WINDSHIELD WIPERS AND WASHERS You can signal another vehicle with your headlights by The wipers and washers are operated by a switch lightly pulling the Multi-Function Control Lever toward on the control lever. The lever is located on the you.
Page 125: Mist Feature
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the OFF position, the wipers Mist Feature will operate for two wipe cycles, then turn OFF. Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle.
Page 126: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
Page 127: Adding Washer Fluid
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared.
Page 128: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 129: To Set At A Desired Speed
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: WARNING! A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake or clutch Leaving the Electronic Speed Control system on pressure while slowing the vehicle will deactivate speed when not in use is dangerous.
Page 130: Manual Transaxle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Tapping “RESUME ACCEL” once will result in a 1 mph WARNING! (1.6 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will Speed Control can be dangerous where the system increase speed by 3 mph (4.8 km/h), etc.
Page 131: Garage Door Opener - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control. GARAGE DOOR OPENER — IF EQUIPPED NOTE: The HomeLink system will be disabled if the Vehicle Theft Alarm (if equipped) is in the Armed or Alarming state.
Page 132: Programming The Universal Transceiver
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Programming The Universal Transceiver WARNING! For best results, install a new battery in the hand held transmitter before programming. If your garage door A moving garage door can cause injury to people and opener (located in the garage) is equipped with an pets in the path of the door.
Page 133 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Choose one of the three Universal Transceiver buttons WARNING! to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its Your motorized door or gate will open and close indicator light in view.
Page 134: Rolling Code" Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 4. Using both hands, press the hand held transmitter transmitter, refer to the Rolling Code Paragraph, or call button and the desired Universal Transceiver button. Do toll free for customer assistance at 1–800–355–3515, or not release the buttons until step 5 has been completed.
Page 135 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press and hold the programmed button on the Univer- 2. Press and hold the training button on the garage door sal Transceiver. If the Universal Transceiver indicator opener head unit. This will activate the “training” light. light flashes rapidly and then stays on after 2 seconds, NOTE: After completing step 2, you have 30 seconds to the device has the “Rolling Code”...
Page 136: Canadian Programming/Gate Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Canadian Programming/Gate Programming Operation Canadian frequency laws, and the technology of some Press and hold the desired button on the Universal entry gates, require you to press and release the hand Transceiver until the garage door or other device begins held transmitter button every two seconds during pro- to operate.
Page 137: Security
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security HomeLink is a trademark owned by Johnson Controls, If you sell your vehicle, be sure to erase the frequencies. Inc. To erase all of the previously trained frequencies, hold ANTI-LOCK BRAKE SYSTEM (ABS) – IF down both outside buttons until the indicator light EQUIPPED begins to flash.
Page 138: Electronic Brake Control System - Abs/Tcs/Bas/Erm/Hdc/Esp
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 ELECTRONIC BRAKE CONTROL SYSTEM – WARNING! ABS/TCS/BAS/ERM/HDC/ESP Your vehicle may be equipped with an optional ad- • Anti-lock system (ABS) cannot prevent the natural vanced electronic brake control system that includes laws of physics from acting on the vehicle, nor can Anti-Lock Brake System (ABS), Traction Control System it increase braking or steering efficiency beyond (TCS), Brake Assist System ( BAS), Electronic Roll Miti-...
Page 139: Traction Control System (Tcs)
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Traction Control System (TCS) Brake Assist System (BAS) This system monitors the amount of wheel spin of each of The BAS is designed to optimize the vehicle’s braking the driven wheels. If wheel spin is detected, brake capability during emergency braking maneuvers.
Page 140: Electronic Roll Mitigation (Erm)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the • BAS cannot prevent the natural laws of physics speed of the vehicle. When ERM determines that the rate from acting on the vehicle, nor can it increase of change of the steering wheel angle and vehicles speed braking efficiency beyond that afforded by the...
Page 141: Hill Descent Control (Hdc) - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE on terrain. The system is activated by placing the vehicle WARNING! in “Off-Road” mode and placing the gear selector in “Low” or “Reverse.” Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance When the system is available, the HDC indica- that wheel lift or rollover may occur.
Page 142: Esp (Electronic Stability Program)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 the accelerator pedal will increase vehicle speed like to the actual path of the vehicle. When the actual path normal. When either the brake or the accelerator is does not match the intended path, ESP applies the brake released, HDC will control the vehicle back to the origi- of the appropriate wheel to assist in counteracting the nal set speed.
Page 143 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP 2WD Operating Modes WARNING! All 2WD vehicles can choose the following ESP operating modes: • Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the ESP ON vehicle, nor can it increase the traction afforded by This is the normal operating mode for ESP.
Page 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 gravel conditions and more wheel spin than ESP would overcome, turn ESP back on by momentarily depressing normally allow is required to gain traction. the “ESP Control Switch”. This may be done while the vehicle is in motion.
Page 145 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In this mode, ESP and TCS, except for the “limited slip” ESP/BAS Warning Light and ESP/TCS Indicator feature described in the TCS section, are turned off until Light the vehicle reaches a speed of 35 mph (56 km/h). At 35 The malfunction indicator for the ESP is combined with mph (56 km/h) the normal ESP stability function returns the BAS indicator.
Page 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: WARNING! • The “ESP Indicator Light” and the “ESP/BAS Warning Light” come on momentarily each time the ignition With the ESP switched off, the enhanced vehicle switch is turned ON. stability offered by ESP is unavailable. In an emer- gency evasive maneuver, the ESP system will not •...
Page 147: Power Sunroof - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located in the reading lamp. • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 148: Opening Sunroof - Manual
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 held forward again. To ensure sunroof is fully closed, OPENING SUNROOF – MANUAL To open the sunroof, press and hold the switch rearward press and hold switch until sunroof has completely to full open. Any release of the switch will stop the stopped moving.
Page 149: Pinch Protect Override
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PINCH PROTECT OVERRIDE SUNSHADE OPERATION If a known obstruction (ice, debris, etc.) prevents closing, The sunshade can be opened manually. However, the press the switch forward and hold for two seconds after sunshade will open automatically as the sunroof opens. the reversal occurs.
Page 150: Sunroof Maintenance
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Sunroof Maintenance WARNING! Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. To Avoid Serious Injury or Death: IGNITION OFF OPERATION • Do not use a 3 - Prong Adaptor. •...
Page 151 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet 115 Volts (150 Watt) Power Outlet 12 Volts...
Page 152: Electrical Outlet Use With Engine Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Electrical Outlet Use With Engine Off CONSOLE FEATURES CAUTION! WARNING! • Many accessories that can be plugged in draw Do not operate this vehicle with the console compart- power from the vehicle’s battery, even when not in ment lid in the open position.
Page 153: Cargo Area Features
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The floor console’s sliding armrest moves forward 3 NOTE: The flip pocket and console lid features are inches to accommodate shorter drivers. The armrest lid intended to be used in the upright or open position only also includes a unique flip pocket for storing a phone or while the vehicle is parked.
Page 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Removing Flashlight Press and Release...
Page 155: Retractable Cargo Area Cover - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three Press Switch Cargo Cover Extended 2. Insert the pins on the ends of the cover into the slots in Retractable Cargo Area Cover — If Equipped To cover the cargo area: the pillar trim cover. 1.
Page 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Cargo Cover Removal WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment.
Page 157: Removable Load Floor
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removable Load Floor Cargo Tie-Down Loops The cargo area load floor is removable and can be There are four D-rings tie-down loops in the lower trim washed with mild soap and water. For removal, lift the for securing cargo.
Page 158: Fold Down Speakers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • Always place cargo evenly on the cargo floor. Put Fold Down Speakers – If Equipped heavier objects as low and as far forward as possible. When the liftgate is open, the speakers can swing down from the trim panel to face rearward, for tailgating and •...
Page 159: Rear Window Features
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch forward to the ON position will activate the wiper.
Page 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Adding Washer Fluid Rear Window Defroster The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Page 161 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE install Mopar cross rails built specifically for this roof CAUTION! rack system or a number of after market rails that are tailored to your lifestyle or activities. Use care when washing the inside of the rear window to prevent damage to heating elements.
Page 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 CAUTION! WARNING! • To prevent damage to the roof of your vehicle, DO NOT Cargo must be securely tied before driving your carry any loads on the roof rack without cross rails vehicle. Improperly secured loads can fly off the installed.
Page 164 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Elapsed Time ......183 Instrument Panel Features ....167 ▫...
Page 165 164 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Two Types Of Signals ....189 ▫ Operating Instructions - Satellite Radio — If Equipped ......199 ▫...
Page 166 UNDERSTANDING YOUR INSTRUMENT PANEL 165 ▫ Using The PTY (Program Type) Button (If Sales Code REC — AM/FM/CD (6–Disc) Radio With Navigation System ..... . 213 Equipped) .
Page 167 166 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Air Conditioning ..... 226 ▫ Operating Tips ..... . . 229 ▫...
Page 168: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 167 INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Glove Box 9 — Hazard Warning Flasher 2 — Demisters 6 — Storage Bin 10 — ESP OFF Switch* 3 — Instrument Cluster 7 — Climate Control * If Equipped 4 —...
Page 169: Instrument Cluster-Premium
168 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM...
Page 170: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 169 3. Electronic Throttle Control Indicator Light INSTRUMENT CLUSTER DESCRIPTIONS This light informs you of a problem with the 1. Fuel Gauge/Fuel Door Location Electronic Throttle Control system. If a prob- When the ignition switch is in the ON position, lem is detected, the light will come on while the the pointer will show the level of fuel remain- engine is running.
Page 171 170 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Oil Pressure Light 6. Speedometer Shows low engine oil pressure. The light will come Indicates vehicle speed. on and remain on when the ignition switch is 7. Airbag Light turned from the OFF to the ON position, and the light The light comes on and remains on for 6 to 8 will turn off after the engine is started.
Page 172 UNDERSTANDING YOUR INSTRUMENT PANEL 171 10. Anti-Lock Warning Light (ABS) — If Equipped on position, but do not start the vehicle. The light should This light monitors the Anti-Lock Brake System come on. If the light does not come on, have the system (ABS) described elsewhere in this manual.
Page 173 172 UNDERSTANDING YOUR INSTRUMENT PANEL will sound 10 times. After the chime turns off, the engine NOTE: The light may flash momentarily during sharp will still be critically hot until the light goes out. cornering maneuvers which change fluid level condi- tions.
Page 174 UNDERSTANDING YOUR INSTRUMENT PANEL 173 In the event of an EBD failure, the Brake Warning Light 15. Transmission Over Temp Light will turn on along with the ABS Light. Immediate repair During sustained high speed driving on hot to the ABS system is required. days, the automatic transaxle oil may become too hot.
Page 175 174 UNDERSTANDING YOUR INSTRUMENT PANEL the pointer drops back into the normal range. If the 20. Transmission Range Indicator pointer remains on the H (red) mark, turn the engine off This display indicator shows the automatic transmission immediately and call for service. gear selection.
Page 176 UNDERSTANDING YOUR INSTRUMENT PANEL 175 vehicle placard or tire inflation pressure label, you should maintain correct tire pressure, even if under-inflation has determine the proper tire inflation pressure for those not reached the level to trigger illumination of the TPMS tires.) low tire pressure telltale.
Page 177 176 UNDERSTANDING YOUR INSTRUMENT PANEL replacing the odometer/trip odometer, vehicle warning CAUTION! messages such as: door/gate ajar and loose gas cap. Loose gas cap will be displayed from the Odometer/Trip The TPMS has been optimized for the original Odometer on all models. equipment tires and wheels.
Page 178 UNDERSTANDING YOUR INSTRUMENT PANEL 177 25. OFF ROAD Light — If Equipped If the Malfunction Indicator Light flashes when the The symbol illuminates (is armed) when the 4WD lock engine is running, serious conditions may exist that switch is activated and the transmission range indicator could lead to immediate loss of power or severe catalytic is in Low or Reverse position.
Page 179 178 UNDERSTANDING YOUR INSTRUMENT PANEL 29. Electronic Stability Program (ESP) Indicator cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your autho- Light/Traction Control System (TCS) Indicator Light — If Equipped rized dealer as soon as possible.
Page 180: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 179 32. Electronic Vehicle Information Center Display—If ELECTRONIC VEHICLE INFORMATION CENTER Equipped (EVIC) – If Equipped When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. 33. Electronic Vehicle Information Center (EVIC) Button—If Equipped Pushing this button, will change the display to the choices available for EVIC.
Page 181 180 UNDERSTANDING YOUR INSTRUMENT PANEL The Electronic Vehicle Information Center (EVIC) fea- When the appropriate conditions exist, the Electronic tures a driver-interactive display. It is located in the lower Vehicle Information Center (EVIC) displays the following left part of the cluster below the fuel and engine tem- messages.
Page 182: Evic Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 181 • Left/Right Front Door Ajar (one or more, with a single EVIC Functions chime if speed is above 1 mph) • Left/Right Rear Door Ajar (one or more, with a single chime if speed is above 1 mph) •...
Page 183: Compass/Temperature/Audio
182 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Compass/Temperature/Audio • Elapsed Time Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is • Tire Pressure Monitor (TPM) facing, the outside temperature and the current radio •...
Page 184: Distance To Empty (Dte)
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Distance To Empty (DTE) Elapsed Time Shows the estimated distance that can be travelled with Shows the total elapsed time of travel since the last reset the fuel remaining in the tank. This estimated distance is when the ignition switch is in the ACC position.
Page 185 184 UNDERSTANDING YOUR INSTRUMENT PANEL Language Auto Unlock On Exit When in this display you may select different languages When ON is selected all the vehicle’s doors will unlock for all display nomenclature, including the trip functions. when the driver’s door is opened if the vehicle is stopped Pressing the EVIC button while in this display selects (manual transmissions) or the vehicle is stopped and the English, Espanol, Deutsch, Italiano, or Francais depend-...
Page 186 UNDERSTANDING YOUR INSTRUMENT PANEL 185 Sound Horn with Remote Key Lock when exiting the vehicle. Press and hold the EVIC button When ON is selected a short horn sound will occur when when in this display until 0, 30, 60, or 90 appears to make the remote keyless entry “Lock”...
Page 187: Setting The Compass Variance And Compass Calibration
186 UNDERSTANDING YOUR INSTRUMENT PANEL power outlets will remain active for up to 60 minutes Display English or Metric after the ignition switch has been turned off. Opening a The EVIC, odometer, and navigation system units can be vehicle door will cancel this feature. Press and hold the changed between English and Metric.
Page 188 UNDERSTANDING YOUR INSTRUMENT PANEL 187 NOTE: Magnetic materials should be kept away from the Instrument Panel. This is where the compass sensor is located.
Page 189: Compass Calibration
188 UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: with the ignition in the ON position, NOTE: The factory default Zone is 8. During program- with a short button press (less than one second) press and ming, the Zone value will wrap around from Zone 15 to release the EVIC button several times until you have Zone 1.
Page 190: Radio General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Programmable Features) menu, press and release (less RADIO GENERAL INFORMATION than one second) the EVIC button several times until Radio Broadcast Signals “Calibrate Compass (Yes)” is displayed. Using a long Your new radio will provide excellent reception under button press (more than one second), pressing the EVIC most operating conditions.
Page 191: Electrical Disturbances
190 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances will remain active for up to 10 minutes after the ignition Radio waves may pick up electrical disturbances during switch has been turned off. Opening a vehicle front door transmission. They mainly affect the wave amplitude, will cancel this feature.
Page 192: Clock Setting Procedure
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Clock Setting Procedure SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND 1. Press and hold the time button until the hours blink. HANDS FREE PHONE CAPABILITY 2. Adjust the hours by turning the right side Tune / NOTE: The radio sales code is located on the lower right Audio control.
Page 193: Operating Instructions - Radio Mode
192 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode Mode Button (Radio Mode) Press the mode button repeatedly to select between the NOTE: The ignition switch must be in the ON or ACC CD player and Satellite Radio (if equipped). position to operate the radio.
Page 194 UNDERSTANDING YOUR INSTRUMENT PANEL 193 NOTE: In Hands Free Phone (if equipped) mode, the Clock Setting Procedure MUTE button mutes the microphone. 1. Press and hold the time button until the hours blink. SCAN Button (Radio Mode) 2. Adjust the hours by turning the right side Tune/ Pressing the SCAN button causes the tuner to search for Audio control.
Page 195 194 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Radio Mode) Press the rotary TUNE control a fourth time and BAL will Turn the right side rotary control clockwise to increase or display. Turn the TUNE control to the right or left to counter-clockwise to decrease the frequency.
Page 196: Operation Instructions - Cd Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 195 selected within 5 seconds after pressing the SET button, Operation Instructions - CD Mode the station will continue to play but will not be stored NOTE: The ignition switch must be in the ON or ACC into push-button memory.
Page 197 196 UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio SCAN Button (CD Mode) OFF, the CD will automatically be pulled into the CD Press this button to play the first 10 seconds of each track. Player.
Page 198: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 197 RND/SET Button (Random Play Button) (CD Operation Instructions - Auxiliary Mode Mode) The auxiliary (AUX) jack is an audio input jack, which Press this button while the CD is playing to activate allows the user to plug in a portable device such as an Random Play.
Page 199: Operating Instructions - Hands Free Phone - If Equipped
198 UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) TIME Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the Press this button to change the display from elapsed speakers. MUTE will display. Press the MUTE button a playing time to time of day.
Page 200: Operating Instructions - Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 201 200 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) SEEK Button (Radio Mode) Press the ON/VOL control to turn the radio ON. Press Press and release the SEEK button to search for the next the ON/VOL a second time to turn OFF the radio. listenable station in either AM/FM or Satellite (if equipped) mode.
Page 202 UNDERSTANDING YOUR INSTRUMENT PANEL 201 SCAN Button (Radio Mode) 2. Adjust the hours by turning the right side Tune / Pressing the SCAN button causes the tuner to search for Audio control. the next listenable station, in either AM, FM or Satellite (if 3.
Page 203 202 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the rotary TUNE control a fifth time and FADE will Press the button to select AM or FM Modes. display. Turn the TUNE control to the left or right to adjust the sound level between the front and rear speak- Setting the Tone, Balance, and Fade ers.
Page 204 UNDERSTANDING YOUR INSTRUMENT PANEL 203 16 Digit-Character Dis- Personality Personality Program Type play Public Public No program type or un- Rhythm and Blues Rhythm_and_Blues None defined Religious Music Religious_Music Adult Hits Adult_Hits Religious Talk Religious_Talk Alert Alert Alert Alert Rock Rock Classical Classical...
Page 205: Operation Instructions - (Cd Mode For Cd Audio Play)
204 UNDERSTANDING YOUR INSTRUMENT PANEL If a preset button is activated while in the PTY (Program FM and 12 Satellite (if equipped) stations to be stored into Type) mode, the PTY mode will be exited and the radio push-button memory. The stations stored in SET 2 will tune to the preset station.
Page 206 UNDERSTANDING YOUR INSTRUMENT PANEL 205 compact discs (CD-RW) compact discs with MP3 tracks show the disc number, the track number, and index time and multisession compact discs with CD and MP3 tracks. in minutes and seconds. Play will begin at the start of track 1.
Page 207: Load/Eject Button (Cd Mode For Cd Audio Play)
206 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE for CD Audio Play) LOAD / EJT - Eject Press the Scan button to scan through each track on the Press the LOAD/ EJT button and the push- CD currently playing. button with the corresponding number where the CD was loaded and the disc will unload LOAD/EJECT Button (CD Mode for CD Audio...
Page 208 UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSERT DISC” for 10 seconds. If no discs are inserted AM/FM Button (CD MODE for CD Audio Play) within 10 seconds “NO DISCS LOADED” will be dis- Switches the Radio to the Radio mode. played. RND/PTY Button (Random Play Button) (CD On some vehicles a disc can be ejected with the radio and MODE for CD Audio Play)
Page 209: Notes On Playing Mp3 Files
208 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 • Maximum number of folders: 100 file recording media and formats are limited. When • Maximum number of characters in file/folder names: writing MP3 files, pay attention to the following restric- tions.
Page 210 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Supported MP3 File Formats MPEG Specifi- Sampling Fre- Bit rate (kbps) The radio will recognize only files with the *.mp3 exten- cation quency (kHz) sion as MP3 files. Non-MP3 files named with the *.mp3 320, 256, 224, extension may cause playback problems.
Page 211: Operation Instructions - (Cd Mode For Mp3 Audio Play)
210 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - (CD Mode for MP3 Audio When a medium containing MP3 data is loaded, the Play) radio checks all files on the medium. If the medium SEEK Button (CD Mode for MP3 Play) contains a lot of folders or files, the radio will take more Pressing the right side of the SEEK button plays the next time to start playing the MP3 files.
Page 212 UNDERSTANDING YOUR INSTRUMENT PANEL 211 LOAD / EJECT - Eject MSG or INFO Button (CD Mode for MP3 Play) Press the LOAD/ EJECT button and the push- Press and MSG or INFO button while playing MP3 disc. button with the corresponding number where The radio scrolls through the following TAG information: the CD was loaded and the disc will unload Song Title, Artist, File Name, and Folder Name (if avail-...
Page 213 212 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Operating Instructions - Hands Free Phone (If Switches back to Radio mode. Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s RND/ PTY Button (CD Mode for MP3 Play) Manual.
Page 214: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Navigation System
UNDERSTANDING YOUR INSTRUMENT PANEL 213 menus and instructions for selecting a variety of destina- SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit.
Page 215 214 UNDERSTANDING YOUR INSTRUMENT PANEL the worldwide standard for time. This makes the sys- 2. To show the GPS clock, select “Displayed Clock: GPS tem’s clock very accurate once the appropriate time zone Clock” and press ENTER. and daylight savings information is set. 3.
Page 216: Audio Clock Display
UNDERSTANDING YOUR INSTRUMENT PANEL 215 1. At the Clock Setup screen highlight “Displayed 3. To decrease the clock by one hour, use the Select Clock: User Defined Clock”. Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4.
Page 217 216 UNDERSTANDING YOUR INSTRUMENT PANEL 1. When you are at an audio screen, quickly press the TIME button on the navigation faceplate. 2. In this example the large clock appears on the screen. 4. To toggle back to the large clock, simply press TIME. 3.
Page 218: Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 217 SATELLITE RADIO — IF EQUIPPED Electronic Serial Number/Sirius Identification Satellite radio uses direct satellite to receiver broadcast- Number (ESN/SID) ing technology to provide clear digital sound, coast to The Electronic Serial Number/Sirius Identification Num- coast. The subscription service provider is Sirius™ Satel- ber is needed to activate your Sirius Satellite Radio lite Radio.
Page 219: Selecting Satellite Mode In Ref, And Raq, Radios
218 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RAQ Radios Selecting Satellite Mode — RAQ Radio With the ignition switch in the ACCESSORY position and Press the MODE button repeatedly until the word SAT the radio OFF, press the CD Eject and TIME buttons appears in the display.
Page 220: Storing And Selecting Pre-Set Channels
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Press and release the SCAN button (if equipped) to Using the PTY (Program Type) Button (if automatically change channels every 7 seconds. The equipped) radio will pause on each channel for 7 seconds before Follow the PTY button instructions that apply to your moving on to the next channel.
Page 221: Pty Button Seek
220 UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button SEEK Reception Quality When the desired program is obtained, press the SEEK Satellite reception may be interrupted due to one of the button within five seconds. The channel will change to following reasons. the next channel that matches the program type selected.
Page 222: Remote Sound System Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 221 The right hand control is a rocker type switch with a push REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED button in the center. Pressing the top of the switch will The remote sound system controls are located on the rear increase the volume and pressing the bottom of the surface of the steering wheel.
Page 223: Cd Player
222 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left hand control CD/DVD DISC MAINTENANCE will tune to the next pre-set station that you have To keep the CD/DVD discs in good condition, take the programmed in the radio pre-set push-buttons. following precautions: 1.
Page 224: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 223 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 225 224 UNDERSTANDING YOUR INSTRUMENT PANEL The air conditioning system of your vehicle contains Mode Control (Air Direction) R-134a, a refrigerant that does not deplete the ozone layer The mode control allows you in the upper atmosphere. to choose from several pat- terns of air distribution.
Page 226 UNDERSTANDING YOUR INSTRUMENT PANEL 225 NOTE: There is a difference in temperature between the Defrost upper and lower outlets for added comfort. The warmer Air is directed through the windshield and side air goes to the floor outlets. This feature gives improved window demist outlets.
Page 227 226 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear seat passen- NOTE: If your air conditioning performance seems gers, the center instrument panel outlets can be aimed, so lower than expected, check the front of the A/C con- that the left center outlet is directed toward the right rear denser: located in front of the radiator, for an accumula- passenger and the right center outlet is directed toward...
Page 228 UNDERSTANDING YOUR INSTRUMENT PANEL 227 NOTE: See “Circulation Control” later in this section, Circulation Control for proper or extended use of this position. Use this button to choose be- tween outside air intake or Air Conditioning (Normal) recirculation of the air inside Use this button to engage the the vehicle.
Page 229 228 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Continuous use of the recirculate mode may charcoal layer. The filter will reduce, but not eliminate, make the inside air stuffy and window fogging may diesel and agricultural smells. The filter acts only on air occur.
Page 230 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Operating Tips...
Page 231 230 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging vehicle. For maximum defogging, press the recirculation Vehicle side windows tend to fog on the inside in mild button until recirculate is off. rainy or humid weather. To clear the windows, set mode Summer Operation to the mix or defrost position.
Page 232 UNDERSTANDING YOUR INSTRUMENT PANEL 231 The blower air will heat faster in cold weather if you use toward the side windows when the system is in either the only a low blower speed for the first few minutes of FLOOR, MIX, or DEFROST mode. The air is directed at vehicle operation.
Page 234 STARTING AND OPERATING CONTENTS ▫ Brake/Transmission Interlock System ..241 Starting Procedures ..... 237 ▫...
Page 235 234 STARTING AND OPERATING ▫ Off-Road Driving Tips And Vehicle ▫ Driving Through Water ....262 Characteristics ..... . . 247 ▫...
Page 236 STARTING AND OPERATING 235 ▫ Base Tire Pressure Monitoring System (TPMS) Tires — General Information ....285 Operation – If Equipped ....294 ▫...
Page 237 236 STARTING AND OPERATING ▫ Fuel System Cautions ....305 ▫ Trailer Hitch Classification ....312 ▫...
Page 238: Starting Procedures
STARTING AND OPERATING 237 STARTING PROCEDURES WARNING! Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Be sure to turn off the engine and remove the key from the ignition switch if you want to rest or sleep WARNING! in your car.
Page 239: Manual Transaxle
238 STARTING AND OPERATING Manual Transaxle WARNING! Before starting the engine fully apply the parking brake, press the clutch pedal to the floor and place the gear Do not attempt to push or tow your vehicle to get it selector in NEUTRAL. started.
Page 240: If Engine Fails To Start
STARTING AND OPERATING 239 If Engine Fails to Start CAUTION! If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. To prevent damage to the starter, do not crank the Push the accelerator pedal all the way to the floor and engine for more than 15 seconds at a time.
Page 241: Automatic Transaxle - If Equipped
240 STARTING AND OPERATING • Shift into PARK only after the vehicle has come to a AUTOMATIC TRANSAXLE — IF EQUIPPED complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 242: Brake/Transmission Interlock System
STARTING AND OPERATING 241 NOTE: If a malfunction occurs, the transaxle will not WARNING! shift out of park. Battery power is required to release the brake/transmission interlock system. There is a remov- It is dangerous to shift the selector lever out of “P” or able plug in the right side of the shifter housing that “N”...
Page 243: Gear Ranges For Continuously Variable
242 STARTING AND OPERATING Gear Ranges For Continuously Variable WARNING! Automatic Transaxle (CVT) DO NOT race the engine when shifting from PARK or Unintended movement of a vehicle could injure NEUTRAL positions into another gear range. those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is “P”...
Page 244 STARTING AND OPERATING 243 • When shifting into P (Park), firmly move the lever all “N” Neutral the way forward until it stops. Engine may be started in this range. • Look at the shift indicator window on the console to “D”...
Page 245: Manual Transaxle Operation
244 STARTING AND OPERATING MANUAL TRANSAXLE OPERATION Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- WARNING! tor pedal. You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.
Page 246: Recommended Shift Speeds
STARTING AND OPERATING 245 Use each gear in numerical order - do not skip a gear. Be Recommended Shift Speeds sure the transaxle is in FIRST gear, (not THIRD), when To use your manual transaxle for optimal fuel economy, starting from a standing position. Damage to the clutch it should be upshifted as listed in table.
Page 247: Four Wheel Drive System - If Equipped
246 STARTING AND OPERATING Four Wheel Drive System — If Equipped CAUTION! This feature provides full time, on-demand, Four Wheel Drive (4WD). If you skip more than one gear while downshifting or downshift at too high a vehicle speed, you could damage the engine, transmission, or clutch.
Page 248: Patriot Freedom Drive Ii - Safe Off-Road Driving
Off-Road Driving Tips and Vehicle Characteristics The Patriot’s Freedom Drive II Off-Road Package The Patriot with the Freedom Drive II Off-Road package The Jeep Patriot with the Freedom Drive II has excellent has excellent on and off-road capabilities. These off-road capability on and off-road.
Page 249: Freedom Drive Ii 4Wd System Operation
248 STARTING AND OPERATING • Unique off-road engine calibration for optimum off- The package includes: road performance with premium fuel • 2.4L DOHC 16-Valve I4 (172 bhp @ 6000 rpm, 165 lb-ft • Off-road Brake Traction Control @ 4400 rpm) •...
Page 250: Freedom Drive Ii - Off-Road Features
STARTING AND OPERATING 249 roads. The active four wheel drive mode has the same the system has the 4WD lock lever engaged and is in functionality with the Freedom Drive I system. Shifting the Low Off-Road mode or reverse. Hill descent the transaxle gear select lever into Low Off-Road mode braking can be turned off by turning off ESP.
Page 251: High Mobility Characteristics
250 STARTING AND OPERATING improved traction capability off-road. It also, turns on High Mobility Characteristics other system features in conjunction with L Off-Road The Patriot with the Freedom Drive II Off-Road package mode. has high off-road mobility characteristics with an ap- proach angle A= 29 degrees, a break-over angle B= 23 •...
Page 252 STARTING AND OPERATING 251 Angles A B C D...
Page 253: Water Fording Characteristics
252 STARTING AND OPERATING Water Fording Characteristics fording characteristics with the ability to cross a pool of Water Fording Characteristics is the vehicle’s ability to water, without stopping, 19 ins. (48 cm) deep at a cross a body of still water, where the powertrain and maximum speed of 5 mph (8 km/h) with an entrance drivetrain are safe from water ingestion.
Page 254 STARTING AND OPERATING 253 Water Fording Characteristics...
Page 255: The Basics Of Off-Road Driving
254 STARTING AND OPERATING The Basics of Off-Road Driving CAUTION! You will encounter many types of terrain driving off- road. You should be familiar with the terrain and area Never park your vehicle over dry grass or other before proceeding. There are many types of surface combustible materials.
Page 256: Simultaneous Brake And Throttle Operation
STARTING AND OPERATING 255 additional traction and activates the numerous off-road Driving in Snow, Mud and Sand features to improve handling and control on slippery or There is a drastic reduction in traction when driving in difficult terrain. Due to the sustained lower gearing, low snow, mud or sand.
Page 257 256 STARTING AND OPERATING hole, get out and determine how deep it is, if there are CAUTION! any hidden obstacles and if the vehicle can be safely recovered if stuck. On icy or slippery roads, do not downshift at high •...
Page 258: Crossing Obstacles (Rocks And Other High Points)
STARTING AND OPERATING 257 on pavement or other hard surfaces. Be sure you have Keeping a firm grip on the steering wheel, bring the a way to air the tires back up prior to reducing the vehicle to a complete stop and then inch the vehicle pressure.
Page 259 258 STARTING AND OPERATING stand a safe distance in front of you where they can see CAUTION! the obstacle, watch your tires and undercarriage, and guide you through. Never attempt to drive over a rock which is large enough to contact the door sills. Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your...
Page 260 STARTING AND OPERATING 259 dirt to fill the rut ahead of the turnout you just created. CAUTION! You should now be able to drive out following the trench you just created at a 45-degree angle. Do not attempted to cross a log with a greater diameter than the running ground clearance or the WARNING! vehicle will become high centered.
Page 261: Hill Climbing
260 STARTING AND OPERATING or other obstacles on the path? Can you safely recover CAUTION! the vehicle if something goes wrong? If everything looks good and you feel confident, then you should Winching or rocking the vehicle off hard objects use low (L Off-Road) with the 4WD Lock engaged and increases the risk of underbody damage.
Page 262 STARTING AND OPERATING 261 a 1/4; turn quickly back and forth. This will provide a distance at the base of the hill to regain control if the fresh bite into the surface and will usually provide vehicle descends to fast? If you feel confident in your enough traction to complete the climb.
Page 263: Driving Through Water
262 STARTING AND OPERATING the possibilities of a down hill slide or roll over. Make WARNING! sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle If the engine stalls or you lose headway or cannot heading slightly up or down.
Page 264 STARTING AND OPERATING 263 avoid damage to the environment. You should know CAUTION! your vehicles abilities and be able to recover it if some- thing goes wrong. You should never stop or shut a Water ingestion into the axles, transmission, transfer vehicle off when crossing deep water unless you ingested case, engine or vehicle interior can occur if you drive water into the engine air intake.
Page 265 264 STARTING AND OPERATING • Before You Cross Any Type Of Water – As you accurate water depth, approach angle, and bottom approach any type of water you need to determine if condition. Murky or muddy water holes are where you can cross it safely and responsibly.
Page 266: Airing Down For Off-Road Driving
STARTING AND OPERATING 265 your tires putting you and your vehicle in jeopardy. WARNING! There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater Never drive through fast moving deep water. It can than the vehicle’s running ground clearance.
Page 267: Vehicle Recovery
266 STARTING AND OPERATING replace it so, start high and lower it as required. Remem- Vehicle Recovery ber you must return the tires to normal air pressure If you drive off-road, you may encounter a situation before driving on road or at highway conditions. Be sure where you will need to recover your vehicle.
Page 268 STARTING AND OPERATING 267 surroundings, then using a tow strap to the vehicle tow vehicle from drive to reverse, while applying throttle hooks would be fast and easy. If the vehicle is severely after each shift. During this process, for additional hung up or in a situation where great care needs to be traction, try turning your steering wheel quickly back taken during the recovery, then nothing can do the job...
Page 269 268 STARTING AND OPERATING the vehicles to allow for a safe recovery. If necessary CAUTION! join two tow straps together using a 1 1/2 in. (4 cm) hard wood dowel. This will keep the straps from Damage can occur when spinning your tires at an becoming knotted and is safer than using a clevis pin excessive high speed.
Page 270: After Driving Off-Road
STARTING AND OPERATING 269 • Check threaded fasteners for looseness, particularly on WARNING! the chassis, drivetrain components, steering, and sus- pension. Retighten them, if required, and torque to the Never use tow straps with end hooks or link two values specified in the Service Manual. straps with a clevis pin.
Page 271: Parking Brake
270 STARTING AND OPERATING If the parking brake is applied while the vehicle is WARNING! moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has Abrasive material in any part of the brakes may cause returned to a stop.
Page 272 STARTING AND OPERATING 271 an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leav- ing the vehicle. WARNING! •...
Page 273: Brake System
272 STARTING AND OPERATING BRAKE SYSTEM If either of the two hydraulic systems lose normal capa- Your vehicle is equipped with power assisted brakes as bility, the remaining system will still function with some standard equipment. In the event power assist is lost for loss of overall braking effectiveness.
Page 274: Anti-Lock Brake System (Abs) - If Equipped
STARTING AND OPERATING 273 Anti-Lock Brake System (ABS) — If Equipped WARNING! The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking Pumping of the Anti-Lock Brakes will diminish their conditions. The system automatically “pumps” the effectiveness and may lead to an accident.
Page 275 274 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake WARNING! System. The light will come on when the ignition switch is turned to the ON position • Anti-lock system (ABS) cannot prevent the natural and may stay on for as long as four seconds. laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond If the ABS light remains on or comes on while driving, it...
Page 276 STARTING AND OPERATING 275 • and a slight drop or fall away of the brake pedal at the When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some end of the stop.
Page 277: Power Steering
276 STARTING AND OPERATING POWER STEERING WARNING! The standard power steering system will give you good vehicle response and increased ease of maneuverability Continued operation with reduced power steering in tight spaces. The system will provide mechanical assist could pose a safety risk to yourself and others. steering capability if power assist is lost.
Page 278: Tire Safety Information
STARTING AND OPERATING 277 • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 279 278 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 280 STARTING AND OPERATING 279 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 281: Tire Identification Number (Tin)
280 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire; tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 282: Tire Loading And Tire Pressure
STARTING AND OPERATING 281 Tire and Loading Information Placard Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire and Loading Information This placard tells you important information about the:...
Page 283 282 STARTING AND OPERATING To determine the maximum loading conditions of your 3) the tire size designed for your vehicle vehicle, locate the statement “The combined weight of 4) the cold tire inflation pressures for the front, rear, occupants and cargo should never exceed XXX kg or XXX and spare tires.
Page 284 STARTING AND OPERATING 283 4. The resulting figure equals the available amount of manual to determine how this reduces the available cargo and luggage load capacity. For example, if “XXX” cargo and luggage load capacity of your vehicle. amount equals 1400 lbs. and there will be five 150 lb. NOTE: The following table shows examples on how to passengers in your vehicle, the amount of available cargo calculate total load, cargo/luggage, and towing capaci-...
Page 285 284 STARTING AND OPERATING...
Page 286: Tires - General Information
STARTING AND OPERATING 285 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can cause acci- increase your stopping distance. Use tires of the dents.
Page 287: Tire Inflation Pressures
286 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 288 STARTING AND OPERATING 287 The pressure should be checked and adjusted as well as (1 km) after a 3 hour period. The cold tire inflation inspecting for signs of tire wear or visible damage at least pressure must not exceed the maximum inflation pres- once a month.
Page 289 288 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 290: Radial-Ply Tires
STARTING AND OPERATING 289 Radial-Ply Tires Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with WARNING! radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the Combining radial ply tires with other types of tires original tire should be repaired (or replaced) and rein- on your vehicle will cause your vehicle to handle...
Page 291: Limited Use Spare - If Equipped
290 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a original equipped tire on the front or rear axle of your conventional tire on the compact spare wheel, since the vehicle, but it is not. Installation of this limited use spare wheel is designed specifically for the compact spare.
Page 292: Tire Spinning
STARTING AND OPERATING 291 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for more than 30 seconds.
Page 293: Life Of Tire
292 STARTING AND OPERATING These indicators are molded into the bottom of the tread WARNING! grooves. They will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the tread is worn to the Tires and spare tire should be replaced after six years, tread wear indicators, the tire should be replaced.
Page 294 STARTING AND OPERATING 293 “Tread Wear Indicators”). Refer to the “Tire and Loading WARNING! Information” placard for the size designation of your tire. The service description and load identification will be • Do not use a tire, wheel size or rating other than that found on the original equipment tire.
Page 295: Alignment And Balance
294 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and Replacing original tires with tires of a different size avoid tire cupping and spotty wear. may result in false speedometer and odometer readings.
Page 296 STARTING AND OPERATING 295 based on cold inflation tire pressure. This is defined as placard pressure in order for the TPM warning lamp to the tire pressure after a vehicle has not been driven for be turned off. The system will automatically update more than 3 hours - and in outside ambient tempera- and the TPM warning lamp will extinguish once the ture.
Page 297: Premium System - If Equipped
296 STARTING AND OPERATING • Various Tire Pressure Monitoring System Messages, Premium System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless which display in the Electronic Vehicle Information technology with wheel rim mounted electronic sensors to Center (EVIC) monitor tire pressure levels.
Page 298 STARTING AND OPERATING 297 NOTE: These display settings may not be available due to Regulatory Authorities. In this case, the display will only show approved units. NOTE: A low spare tire will not cause the Tire Pressure Monitoring Telltale Lamp to illuminate or the chime to sound.
Page 299 298 STARTING AND OPERATING Check TPM System Message The Tire Pressure Monitoring Telltale Light will flash on and off for 60 seconds, and an audible chime will sound when a system fault is detected. The flash cycle will repeat every ten minutes, without an audible chime, until the fault condition no longer exists.
Page 300 STARTING AND OPERATING 299 Display Settings EVIC. This text message will then be followed by a graphic, with “- -“ in place of the flashing low pressure • Your system can be set to display pressure units in PSI, value. For every subsequent key cycle, the “Tire Pressure kPa, or BAR.
Page 301 300 STARTING AND OPERATING CAUTION! CAUTION! The TPMS has been optimized for the original After inspecting or adjusting the tire pressure, al- equipment tires and wheels. TPMS pressures have ways reinstall the valve stem cap. This will prevent been established for the tire size equipped on your moisture and dirt from entering the valve stem, vehicle.
Page 302: General Information
STARTING AND OPERATING 301 • This device must accept any interference received, Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and including interference that may cause undesired op- stopping ability. eration. • The TPMS is not a substitute for proper tire mainte- The tire pressure sensors are covered under one of the nance, and it is the driver’s responsibility to maintain following licenses:...
Page 303: Snow Tires
302 STARTING AND OPERATING SNOW TIRES Tire Rotation Recommendations Some areas of the country require the use of snow tires Tires on the front and rear axles of vehicles operate at during winter. Standard tires are of the all season type different loads and perform different steering, driving, and satisfy this requirement as indicated by the M+S and braking functions.
Page 304: Fuel Requirements
STARTING AND OPERATING 303 wear should be corrected before rotating. The suggested recommended. The use of premium gasoline will provide rotation method is the “forward-cross” shown in the no benefit over high quality regular gasolines, and in diagram. some circumstances, may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine.
Page 305: Gasoline/Oxygenate Blends
304 STARTING AND OPERATING Reformulated gasolines contain oxygenates, and are spe- CAUTION! cifically blended to reduce vehicle emissions and im- prove air quality. DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting The manufacturer supports the use of reformulated gaso- and driveability problems and may damage critical lines.
Page 306: Materials Added To Fuel
STARTING AND OPERATING 305 performance in some vehicles. The manufacturer recom- Fuel System Cautions mends using gasolines without MMT. Since the MMT CAUTION! content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not Follow these guidelines to maintain your vehicle’s his/her gasoline contains MMT.
Page 307: Carbon Monoxide Warnings
306 STARTING AND OPERATING • Do not inhale exhaust gases. They contain carbon products contain high concentrations of methanol. Fuel system damage or vehicle performance problems monoxide, a colorless and odorless gas which can kill. resulting from the use of such fuels or additives is not Never run the engine in a closed area, such as a the responsibility of the manufacturer.
Page 308: Adding Fuel
STARTING AND OPERATING 307 ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) Damage to the fuel system or emission control sys- The gas cap is behind the fuel filler door, on the left side tem could result from using an improper fuel tank of the vehicle.
Page 309: Loose Fuel Filler Cap Message
308 STARTING AND OPERATING NOTE: When the fuel nozzle “clicks” or shuts off, the If the gas cap is not tighten properly, the Malfunction fuel tank is full. Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! WARNING! •...
Page 310: Vehicle Loading
STARTING AND OPERATING 309 problem continues, the message will appear the next time TRAILER TOWING the vehicle is started. Refer to “Onboard Diagnostic In this section you will find safety tips and information System — OBDII” in Section 7 of this manual for more on limits to the type of towing you can reasonably do information.
Page 311 310 STARTING AND OPERATING Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The gross trailer weight (GTW) is the weight of the trailer The GAWR is the maximum capacity of the front and rear plus the weight of all cargo, consumables and equipment axles.
Page 312 STARTING AND OPERATING 311 Frontal Area Weight-Distributing Hitch The maximum height and maximum width of the front of A weight-distributing system works by applying lever- a trailer. age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to Trailer Sway Control the tow vehicle’s front axle and the trailer axle(s).
Page 313: Trailer Hitch Classification
312 STARTING AND OPERATING The following chart provides the industry standard for WARNING! the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the An improperly adjusted Weight Distributing Hitch correct trailer hitch for your intended towing condition.
Page 314: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 313 All trailer hitches should be professionally installed on Trailer Towing Weights (Maximum Trailer Weight Rat- your vehicle. ings) Trailer Towing Weights (Maximum Trailer Weight The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
Page 315: Trailer And Tongue Weight
314 STARTING AND OPERATING Engine/Transmission Frontal Area Max. GTW (Gross Trailer Max. Tongue Wt. (See Wt.) Note 1) 2.4L Auto/Man 22 Sq. Ft. (2.04 Sq. m) 1000 lbs (450 kg) 150 lbs (68 kg) 2.4L Auto/Man with Trailer 32 Sq. Ft. (3.0 Sq. m) 2000 lbs (450 kg) 225 lbs (102 kg) Tow Prep Package (AHC)
Page 316: Towing Requirements
STARTING AND OPERATING 315 • The weight of any other type of cargo or equipment Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
Page 317 316 STARTING AND OPERATING CAUTION! WARNING! • Avoid towing a trailer for the first 500 miles (805 Improper towing can lead to an injury accident. km) of vehicle operation. Doing so may damage Follow these guidelines to make your trailer towing your vehicle.
Page 318 STARTING AND OPERATING 317 • Safety chains must always be used between your 4. Tongue weight rating for the trailer hitch utilized vehicle and trailer. Always connect the chains to the (This requirement may limit the ability to always frame or hook retainers of the vehicle hitch. Cross the achieve the 10% to 15% range of tongue weight as a chains under the trailer tongue and allow enough percentage of total trailer weight).
Page 319 318 STARTING AND OPERATING − When replacing tires refer to the Tires–General Infor- − Trailer brakes are recommended for trailers over 1,000 mation section of this manual on Replacement Tires for lbs (454 kg) and required for trailers in excess of 2,000 proper tire replacement procedures.
Page 320 STARTING AND OPERATING 319 The Trailer Tow Package may include a 4 and 7 pin WARNING! wiring harness. Use a factory approved trailer harness and connector. Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- NOTE: Do not cut or splice wiring into the vehicles tem and cause it to fail.
Page 321: Towing Tips
320 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy 4 - Pin Connector traffic.
Page 322 STARTING AND OPERATING 321 Towing Tips — Automatic Transmission Towing Tips — Cooling System The automatic transmission fluid and filter should be To reduce potential for engine and transmission over- changed if you REGULARLY tow a trailer for more than heating, take the following actions: 45 minutes of continuous operation.
Page 323: Recreational Towing (Behind Motorhome, Etc.)
322 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND NOTE: If the vehicle requires towing make sure all four wheels are off the ground. MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) CAUTION! DO NOT flat tow this vehicle.
Page 324: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....324 Jump-Starting Procedures Due To A Low Battery ......331 If Your Engine Overheats .
Page 325: Hazard Warning Flasher
324 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
Page 326 WHAT TO DO IN EMERGENCIES 325 the normal range. If the pointer remains on the H (red) CAUTION! mark for more than a minute, turn the engine off imme- diately and call for service. Driving with a hot cooling system could damage your vehicle.
Page 327: Automatic Transaxle Overheating
326 WHAT TO DO IN EMERGENCIES requested speed. If the high speed is maintained, the WARNING! overheating will reoccur, as before, in a cyclic fashion. A hot engine cooling system is dangerous. You or JACKING AND TIRE CHANGING others could be badly burned by steam or boiling coolant.
Page 328: Jack Location
WHAT TO DO IN EMERGENCIES 327 Jack Location Spare Tire Stowage The jack and jack-handle are stowed under the load floor The spare tire is stowed under the rear load floor in the in the cargo area. cargo area. Spare Tire Removal Lift up the load floor cover and remove the hold down.
Page 329: Jacking Instructions
328 WHAT TO DO IN EMERGENCIES • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if changing the right front tire, block the left rear wheel.
Page 330 WHAT TO DO IN EMERGENCIES 329 3. There are two front jacking locations and two rear WARNING! jacking locations on each side of the body. The front locations are outlined by two triangular cutouts, the rear Raising the vehicle higher than necessary can make ones by two rectangular cutouts.
Page 331 330 WHAT TO DO IN EMERGENCIES 7. Lower the vehicle by turning the jack screw to the left. 10. Place the deflated (flat) tire in the cargo area, have the tire repaired or replaced as soon as possible. 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts.
Page 332: Jump-Starting Procedures Due To A Low Battery
WHAT TO DO IN EMERGENCIES 331 JUMP-STARTING PROCEDURES DUE TO A LOW WARNING! BATTERY Do not attempt to push or tow your vehicle to get it WARNING! started. Vehicles equipped with an automatic trans- axle cannot be started this way and may be damaged. Take care to avoid the radiator cooling fan whenever Unburned fuel could enter the catalytic converter and the hood is raised.
Page 333 332 WHAT TO DO IN EMERGENCIES NOTE: Disconnecting the battery with the ignition in WARNING! the On position will cause vehicles with an automatic transaxle (CVT2) to go into “default mode” and turn on Wear eye protection and remove any metal jewelry the malfunction indicator light.
Page 334 WHAT TO DO IN EMERGENCIES 333 5. Connect one end of a jumper cable to the positive 6. Connect the other cable, first to the negative terminal terminal of the booster battery. Connect the other end of of the booster battery and then to the negative terminal of the jumper cable to the positive terminal of the dis- the discharged battery.
Page 335: Driving On Slippery Surfaces
334 WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 336: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 335 FREEING A STUCK VEHICLE WARNING! NOTE: If your vehicle is equipped with Traction Con- Fast spinning tires can be dangerous. Forces gener- trol, turn the system OFF before attempting to “rock” the ated by excessive wheel speeds may cause axle, tire vehicle.
Page 337: Towing A Disabled Vehicle
336 WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can If the vehicle being towed requires steering, the also damage the tires. Do not spin the wheels above ignition switch must be in the ACCESSORY posi- 30 mph (48 km/h).
Page 338: Without The Ignition Key
WHAT TO DO IN EMERGENCIES 337 Towing This Vehicle Behind Another Vehicle (Flat Without The Ignition Key Special care must be taken when the vehicle is towed Towing With All Four Wheels On The Ground) with the ignition in the LOCK position. A dolly should be CAUTION! used under the front wheels if the rear wheels are raised.
Page 340 MAINTAINING YOUR VEHICLE CONTENTS ▫ Drive Belt – Check Condition ... . . 351 Engine Compartment — Gasoline Engines ..342 ▫ Spark Plugs ......351 Onboard Diagnostic System —...
Page 341 340 MAINTAINING YOUR VEHICLE ▫ Front Suspension Ball Joints ....357 ▫ Power Transfer Unit (PTU) – AWD/4WD Models Only ......371 ▫...
Page 342 MAINTAINING YOUR VEHICLE 341 ▫ Engine ......388 Fluids And Capacities ....388 ▫...
Page 343: Engine Compartment - Gasoline Engines
342 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — GASOLINE ENGINES...
Page 344: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 343 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 345: Loose Fuel Filler Cap Message
344 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE After fuel is added, the vehicle diagnostic system can PROGRAMS determine if the fuel filler cap is possible loose or In some localities, it may be a legal requirement to pass improperly installed.
Page 346 MAINTAINING YOUR VEHICLE 345 Your vehicle has a simple ignition key actuated test, ignition key or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD system is not ready and you should not check if your vehicle’s OBD system is ready, you must do proceed to the I/M station.
Page 347: Replacement Parts
346 MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M NOTE: Intentional tampering with emissions control station can fail your vehicle because the MIL symbol is on systems can result in civil penalties being assessed with the engine running. against you.
Page 348: Maintenance Procedures
MAINTAINING YOUR VEHICLE 347 The best time to check the engine oil level is about 5 MAINTENANCE PROCEDURES The pages that follow contain the required maintenance minutes after a fully warmed engine is shut off. Do not services determined by the engineers who designed your check oil level before starting the engine after it has sat vehicle.
Page 349 348 MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground and Change Engine Oil only when the engine is hot, will improve the accuracy of Road conditions and your kind of driving affects the the oil level readings. Maintain the oil level between the interval at which your oil should be changed.
Page 350 MAINTAINING YOUR VEHICLE 349 NOTE: If ANY of these apply to you then change your American Petroleum Institute (API) Engine Oil engine oil every 3,000 miles (5 000 km) or 3 months, Identification Symbol whichever comes first, and follow schedule “B—All This symbol means that the oil has Engines”...
Page 351 350 MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certi- Disposing of Used Engine Oil fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil from ber should not be used. your vehicle.
Page 352: Drive Belt - Check Condition
MAINTAINING YOUR VEHICLE 351 Drive Belt – Check Condition Catalytic Converter At the mileage shown in the maintenance schedules, The catalytic converter requires the use of unleaded fuel check the drive belt for condition. only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
Page 353 352 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your A hot exhaust system can start a fire if you park over vehicle is not kept in proper operating condition. In materials that can burn. Such materials might be the event of engine malfunction, particularly involv- grass or leaves coming into contact with your exhaust ing engine misfire or other apparent loss of perfor-...
Page 354: Crankcase Emission Control System
MAINTAINING YOUR VEHICLE 353 To minimize the possibility of catalyst damage: Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in Fuel Filter motion.
Page 355: Maintenance-Free Battery
354 MAINTAINING YOUR VEHICLE WARNING! CAUTION! The air cleaner can provide a measure of protection When servicing the battery, always reinstall the bat- in the case of engine backfire. Do not remove the air tery thermowrap. The thermowrap provides battery cleaner unless such removal is necessary for repair or heat protection and will extend overall battery life.
Page 356 MAINTAINING YOUR VEHICLE 355 WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn It is essential when replacing the cables on the or even blind you. Don’t allow battery fluid to battery that the positive cable is attached to the contact your eyes, skin or clothing.
Page 357: Air Conditioner Maintenance
356 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer • Use only refrigerants and compressor lubricants at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 358: Power Steering - Fluid Check
MAINTAINING YOUR VEHICLE 357 Refrigerant Recovery and Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- Fluid level should be checked on a level surface and tection Agency and is an ozone-saving product. How- with the engine off to prevent injury from moving ever, the manufacturer recommends that air conditioning parts and to insure accurate fluid level reading.
Page 359: Body Lubrication
358 MAINTAINING YOUR VEHICLE Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as Clean the rubber edges of the wiper blades and the seat tracks, doors, liftgate and hood hinges, should be windshield periodically with a sponge or soft cloth and a lubricated periodically to assure quiet, easy operation mild nonabrasive cleaner or use the washer solvent.
Page 360: Windshield Washer Reservoir
MAINTAINING YOUR VEHICLE 359 2. Push the release tab and slide the wiper blade assem- when the underside or rear of the vehicle is damaged; bly down along the arm. Gently place the wiper arm on have a competent technician inspect the complete ex- the windshield.
Page 361: Cooling System
360 MAINTAINING YOUR VEHICLE Cooling System Coolant Checks Check engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the • When working near the radiator cooling fan, dis- system should be drained, flushed and refilled with fresh connect the fan motor lead or turn the ignition coolant.
Page 362 MAINTAINING YOUR VEHICLE 361 system cleaner. Follow with a thorough rinsing to remove CAUTION! all deposits and chemicals. Properly dispose of old antifreeze solution. Mixing of coolants other than specified Hybrid Or- ganic Additive Technology (HOAT) engine coolants, Selection Of Coolant may result in engine damage and may decrease Use only the manufacturers recommended coolant, refer corrosion protection.
Page 363 362 MAINTAINING YOUR VEHICLE Adding Coolant The use of lower quality water will reduce the amount of Your vehicle has been built with an improved engine corrosion protection in the engine cooling system. coolant that allows extended maintenance intervals. This Please note that it is the owner’s responsibility to main- coolant can be used up to 5 Years or 100,000 miles before tain the proper level of protection against freezing ac-...
Page 364 MAINTAINING YOUR VEHICLE 363 community. To prevent ingestion by animals or children WARNING! do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the • The warning words “DO NOT OPEN HOT” on ground.
Page 365 364 MAINTAINING YOUR VEHICLE • Check coolant freeze point in the radiator and in the When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do coolant recovery bottle. If antifreeze needs to be not overfill.
Page 366: Hoses And Vacuum/Vapor Harnesses
MAINTAINING YOUR VEHICLE 365 • Do not change the thermostat for summer or winter Inspect all hose connections such as clamps and cou- operation. If replacement is ever necessary, install plings to make sure the are secure and no leaks are ONLY the correct type thermostat.
Page 367: Brake System
366 MAINTAINING YOUR VEHICLE Brake System brittle rubber, cracking, tears, cuts, abrasions, and exces- In order to assure brake system performance, all brake sive swelling suggest deterioration of the rubber. Particu- system components should be inspected periodically. lar attention should be made to examining those hose Suggested service intervals can be found in the Mainte- surfaces nearest to high heat sources, such as the exhaust nance Section.
Page 368 MAINTAINING YOUR VEHICLE 367 NOTE: Inspection of brake hoses should be done when- fluid reservoir. Fluid level can be expected to fall as the ever the brake system is serviced and at every engine oil brake pads wear. Brake fluid level should be checked change.
Page 369: Automatic Transaxle (Cvt)
368 MAINTAINING YOUR VEHICLE WARNING! WARNING! Use of a brake fluid that may have a lower initial Overfilling the brake fluid reservoir can result in boiling point or unidentified as to specification, may spilling brake fluid on hot engine parts and the result in sudden brake failure during hard prolonged brake fluid catching fire.
Page 370: Manual Transaxle
MAINTAINING YOUR VEHICLE 369 steel belt traction on the drive and driven pulleys. Refer Fluid and Filter Changes to Fluids, Lubricants and Genuine Parts for correct fluid Refer to the “Maintenance Schedule located if section 8 of type. this manual for the correct change interval for your type of driving.
Page 371: Rear Drive Assembly (Rda )- Awd/4Wd Models Only
370 MAINTAINING YOUR VEHICLE Fluid Level Check Rear Drive Assembly (RDA )– AWD/4WD Models Check the fluid level by removing the fill plug. The fluid Only level should be between the bottom of the fill hole and a Lubricant Selection point not more that 3/16”...
Page 372: Power Transfer Unit (Ptu) - Awd/4Wd Models Only
MAINTAINING YOUR VEHICLE 371 Power Transfer Unit (PTU) – AWD/4WD Models Appearance Care And Protection From Corrosion Only Protection Of Body And Paint from Corrosion Lubricant Selection Vehicle body care requirements vary according to geo- Use only manufacturers recommended fluid. Refer to graphic locations and usage.
Page 373 372 MAINTAINING YOUR VEHICLE • Use Mopar Cleaner Wax to remove road film, stains The most common causes are: and to protect your paint finish. Take care never to • Road salt, dirt and moisture accumulation. scratch the paint. • Stone and gravel impact. •...
Page 374 MAINTAINING YOUR VEHICLE 373 • It is important that the drain holes in the lower edges • Use Mopar touch up paint on scratches as soon as of the doors, rocker panels and trunk be kept clear and possible. Your dealer has touch up paint to match the open.
Page 375 374 MAINTAINING YOUR VEHICLE • Remove as much of the stain as possible by blotting Mopar Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth.
Page 376 MAINTAINING YOUR VEHICLE 375 Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household- Do not use volatile solvents for cleaning purposes. type glass cleaner. Never use an abrasive type cleaner. Many are potentially flammable, and if used in Use caution when cleaning the inside rear window closed areas they may cause respiratory harm.
Page 377: Fuses/Integrated Power Module (Ipm)
376 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses Replace the belts if they appear frayed or worn or if the The lenses in front of the instruments in this vehicle are buckles do not work properly. molded in clear plastic. When cleaning the lenses, care Dry with a soft tissue.
Page 378 MAINTAINING YOUR VEHICLE 377 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse Empty Empty 40 Amp Power Seats Green 15 Amp AWD/4WD ECU Lt. Blue Feed 20 Amp CCN Power Locks Yellow 10 Amp CHMSL Brake Switch Feed 15 Amp Power Outlet...
Page 379 378 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 10 Amp IOD Feed Mod-Wcm 10 Amp Heated Mirror 40 Amp ASD Relay Contact 15 Amp ENG ASD Relay Feed Green PWR Feed Lt. Blue 20 Amp PWR Amp 1 &...
Page 380 MAINTAINING YOUR VEHICLE 379 Cavity Cartridge Mini Description CAUTION! Fuse Fuse • When installing the Integrated Power Module 10 Amp ABS MOD/J1962 Conn/PCM cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so 30 Amp ABS Valve Feed Pink...
Page 381: Vehicle Storage
380 MAINTAINING YOUR VEHICLE VEHICLE STORAGE LIGHTS BULBS — Outside Bulb No. If you will not be using your vehicle for more than 21 Low Beam/High Beam Headlight ... . H13 days you may want to take steps to preserve your battery.
Page 382: Bulb Replacement
MAINTAINING YOUR VEHICLE 381 BULB REPLACEMENT Headlamps Releasing Red Lock Tab Locating Headlamp Connector • Raise the hood and locate connector behind the head- lamp.
Page 383 382 MAINTAINING YOUR VEHICLE • Reach into engine compartment and pull red lock out at connector. Twisting Bulb From Socket • Twist the bulb to the left and pull outward from assembly. Remove green connector from back of bulb by pulling straight back...
Page 384: Fog Lights
MAINTAINING YOUR VEHICLE 383 NOTE: These are halogen bulbs. Take care not to touch Fog Lights the bulb with your fingers. Body oils from your fingers See your authorized dealer for replacement. could cause excessive heat buildup which reduces bulb life.
Page 385: Tail Lights, Rear Turn Signals And Backup Lights - Replacement
384 MAINTAINING YOUR VEHICLE Tail Lights, Rear Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing. Push-Pins Removed 2. Grasp the tail lamp and pull firmly to disengage the lamp from the aperture panel. Removing Push-Pins...
Page 386 MAINTAINING YOUR VEHICLE 385 Pulling Lamp From Body Removing Socket and Bulb 3. Twist and remove socket from lamp.
Page 387: License Lights
386 MAINTAINING YOUR VEHICLE 4. Remove bulb from socket and replace. License Lights 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. Removing Bulb From Socket Prying Lamp from Liftgate 2.
Page 388: Center High-Mounted Stoplight
MAINTAINING YOUR VEHICLE 387 Removing Socket from Lamp Removing Bulb From Socket 3. Pull bulb from socket. Center High-Mounted Stoplight Light is an LED assembly. See your authorized dealer for replacement.
Page 389 388 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 13.5 Gallons 51.0 Liters Engine Oil-With Filter All Gasoline Engines (Use API Certified SAE 5W-20 Engine 4.5 Quarts 4.26 Liters Oil.) Cooling System * Mopar Antifreeze/Coolant 5 Year/100,000 Miles Formula), or 7.2 Quarts 6.8 Liters equivalent.
Page 390 MAINTAINING YOUR VEHICLE 389 Component Fluids, Lubricants and Genuine Parts Engine Oil Filter Mopar 04884900AB or equivalent. Spark Plugs Refer to the Vehicle Emission Control Information label in the engine com- partment. Fuel Selection 87 Octane (R + M)/2 Chassis Component Fluids, Lubricants and Genuine Parts.
Page 392 MAINTENANCE SCHEDULES CONTENTS ▫ Schedule “B” ......395 Emission Control System Maintenance ..392 ▫...
Page 393: Emission Control System Maintenance
392 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule “B”.
Page 394 MAINTENANCE SCHEDULES 393 • Off-road or desert operation. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months • Heavy Loading whichever comes first. NOTE: If ANY of these apply to you then change your CAUTION! engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B”...
Page 395 394 MAINTENANCE SCHEDULES • Inspect the CV joints (if equipped) and front suspen- Once a Month sion components. • Check tire pressure and look for unusual wear or • Check the manual transmission fluid level (if damage. equipped). • Inspect the battery and clean and tighten the terminals •...
Page 396: Schedule "B" 395
SCHEDULE “B” 395 • Taxi, police, or delivery service (commercial service). Schedule “B” Follow schedule “B” if you usually operate your vehicle • Off-road or desert operation. under one or more of the following conditions. • Heavy Loading • Day or night temperatures are below 32 °F (0 °C). NOTE: If ANY of these apply to you then change your •...
Page 397 396 SCHEDULE “B” Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 398 SCHEDULE “B” 397 Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 399 398 SCHEDULE “B” Miles 33,000 36,000 39, 000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 400 SCHEDULE “B” 399 Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Change Automatic Transaxle (CVT) Fluid and Filter Change Manual Transaxle Fluid.
Page 401 400 SCHEDULE “B” Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 402 SCHEDULE “B” 401 Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 403 402 SCHEDULE “B” Miles 93,000 96,000 99,000 102,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Change Manual Transaxle Fluid. Rotate tires. Check spare tire for proper pressure and correct stowage. Flush and replace engine coolant, if not done at 60 months.
Page 404 SCHEDULE “B” 403 Miles 105,000 108,000 111,000 114,000 117,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter, or at 3 months whichever comes first. Change Automatic Transaxle (CVT) Fluid and Filter Change Rear Drive Assembly (RDA) fluid.
Page 405 404 SCHEDULE “B” Miles 105,000 108,000 111,000 114,000 117,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Replace climate control air filtration filter (if equipped). ** This maintenance is recommended by the manufac- turer to the owner, but not required to maintain the emissions warranty.
Page 406: Schedule "A
SCHEDULE “A” 405 Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000 ) (50 000) [Months] [12] [18] [24] [30] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 407 406 SCHEDULE “A” Miles 36,000 42,000 48,000 54000 60,000 66,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [36] [42] [48] [54] [60] [66] Change engine oil and engine oil filter. Change Rear Drive Assembly (RDA) fluid. Change Power Transfer Unit (PTU) fluid.
Page 408 SCHEDULE “A” 407 Miles 72,000 78,000 84,000 90,000 96,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) [Months] [72] [78] [84] [90] [96] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage.
Page 409 408 SCHEDULE “A” Miles 102,000 108,000 114,000 120,000 (Kilometers) (170 000) (180 000) (190 000) (200 000) [Months] [102] [108] [114] [120] Change engine oil and engine oil filter. Change Rear Drive Assembly (RDA) fluid. Change Power Transfer Unit (PTU) fluid. Rotate tires.
Page 410 SCHEDULE “A” 409 ** This maintenance is recommended by the manufac- WARNING! turer to the owner, but not required to maintain the emissions warranty. You can be badly injured working on or around a motor vehicle. Do only that service work for which Inspection and service should also be performed anytime you have the knowledge and the right equipment.
Page 412: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Reporting Safety Defects ....415 Your Vehicle ......412 ▫...
Page 413: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized or work done that is not on your maintenance log, let the Chrysler, Dodge, or Jeep dealer. We strongly recommend service advisor know. that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 414 IF YOU NEED CONSUMER ASSISTANCE 413 • Vehicle identification number technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely • Vehicle delivery date and mileage manner. DaimlerChrysler Motors Corporation Customer Center This is why you should always talk to your dealer’s P.O.
Page 415 414 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na- tional Customer Hotline at 1-800-521-9922. Impaired (TDD/TTY) To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 416: Warranty Information (U.s. Vehicles Only)
IF YOU NEED CONSUMER ASSISTANCE 415 MOPAR PARTS WARNING! Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your Engine exhaust, some of its constituents, and certain vehicle operating at its best. vehicle components contain or emit chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS birth defects or other reproductive harm.
Page 417: In Canada
416 IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– To order the following manuals, you may use either the 9153), or go to http://www.safercar.gov; or write to: website or the phone numbers listed below.
Page 418: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 417 • Diagnostic Procedure Manuals. Call Toll Free at: • 1–800–890–4038 (U.S.) Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and • 1–800–387–1143 (Canada) technicians to find and fix problems on computer- controlled vehicle systems and features.
Page 419: Treadwear
418 IF YOU NEED CONSUMER ASSISTANCE All Passenger Car Tires Must Conform to Federal Safety Traction Grades Requirements in Addition to These Grades. The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on Treadwear wet pavement as measured under controlled conditions The treadwear grade is a comparative rating based on the...
Page 420: Temperature Grades
IF YOU NEED CONSUMER ASSISTANCE 419 Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat when tested under a tire that is properly inflated and not overloaded.
Page 422 INDEX...
Page 423 422 INDEX ABS (Anti-Lock Brake System) ....273 Alignment and Balance ....294 Adding Engine Coolant (Antifreeze) .
Page 424 INDEX 423 Battery ....... 354 Calibration, Compass ..... 188 Keyless Transmitter Replacement (RKE) .
Page 425 424 INDEX CD (Compact Disc) Player Maintenance ..222 Coin Holder ......151 Cellular Phone .
Page 426 INDEX 425 Crankcase Emission Control System ..353 Drive Belts ......351 Cruise Light .
Page 427 426 INDEX Emergency, In Case of Temperature Gauge ..... 173 Jacking ......326 Enhanced Accident Response Feature .
Page 428 INDEX 427 Fluid Level Checks Gauge ......169 Automatic Transaxle ....369 Hoses .
Page 429 428 INDEX Tachometer ......171 Hill Descent Control ....140,177 Gearshift .
Page 430 INDEX 429 Interior Appearance Care ....374 Latches Intermittent Wipers (Delay Wipers) ... 125 Hood .
Page 431 430 INDEX Headlight Switch ..... . 119 Locks Headlights ......119 Child Protection .
Page 432 INDEX 431 Fluid Level Check ....370,371 Occupant Restraints ..... . . 36 Frequency of Fluid Change .
Page 433 432 INDEX Opener, Garage Door (HomeLink ) ... 130 Mirrors ......80 Operator Manual (Owner’s Manual) .
Page 434 INDEX 433 Radio, Navigation ..... . . 213 Remote Sound System (Radio) Controls ..221 Radio Operation .
Page 435 434 INDEX Satellite Radio Antenna ....220 Lumbar Support ..... . . 109 Schedule, Maintenance .
Page 436 INDEX 435 Signals, Turn ......384 Steering Wheel Mounted Sound Slippery Surfaces, Driving On ....334 System Controls .
Page 437 436 INDEX Tire and Loading Information Placard ..281 Quality Grading ..... . . 417 Tire Identification Number (TIN) .
Page 438 INDEX 437 Hitches ......312 Transporting Pets ......68 Minimum Requirements .
Page 439 438 INDEX Vehicle Theft Alarm (Security Alarm) ..30 Wind Buffeting ......148 Window Airbag (Side Curtain) .
Page 440 81-326-0712 First Edition Printed in U.S.A.

Jeep 2007 Patriot Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

Chapters

Related Manuals for Jeep 2007 Patriot

Summary of Contents for Jeep 2007 Patriot