Furuno FS-1570 Installation Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Telephone
  5. FS-1570
  6. Installation manual

Furuno FS-1570 Installation Manual

Ssb radiotelephone 150 w and 250w
Hide thumbs Also See for FS-1570:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual

SSB RADIOTELEPHONE

FS-1570 (150 W)
FS-2570 (250 W)
PRINTED IN JAPAN

Advertisement

Table of Contents
loading

Related Manuals for Furuno FS-1570

Summary of Contents for Furuno FS-1570

  • Page 1: Ssb Radiotelephone

    SSB RADIOTELEPHONE FS-1570 (150 W) FS-2570 (250 W) PRINTED IN JAPAN...
  • Page 2 *00080934200* *00080934200* *00080934200* *00080934200* ( ( HIMA HIMA ) ) FS-1570/2570 FS-1570/2570 * 0 0 0 8 0 9 3 4 2 0 0 * * 0 0 0 8 0 9 3 4 2 0 0 * *IME56360B00* *IME56360B00*...

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS CAUTION DANGER Do not touch cable from Confirm that the power supply voltage the antenna coupler during is compatible with the voltage rating transmission. of the equipment. Electrical shock, serious Connection to the wrong power supply injury or death can result if can cause fire or equipment damage to the the cables are touched during equipment .

  • Page 4: Table Of Contents

    TABLE OF CONTENTS SYSTEM CONFIGURATION ....................iii EQUIPMENT LISTS ......................v 1. MOUNTING ........................1-1 1.1 Control Unit ............................1-1 1.2 Antenna Coupler........................... 1-3 1.3 Transceiver Unit ........................... 1-8 1.4 Handset (w/bracket) ..........................1-9 1.5 The Antenna ............................1-10 1.6 Mounting of Optional Equipment......................1-11 2.

  • Page 5: System Configuration

    SYSTEM CONFIGURATION FS-1570 For DSC distress PREAMP Antenna Coupler FAX-5 AT-1560-15 LOUDSPEAKER SEM-21Q NAVIGATOR HANDSET CONTROL UNIT HS-2001 FS-2570C INCOMING INDICATOR PRINTER IC-303-DSC NBDP CONTROLLER PP-510 IB-581 TRANSCEIVER UNIT NBDP TERMINAL UNIT TELEX DISTRESS FSC-1570T PRINTER IB-583 ALERT BUTTON INTERFACE...
  • Page 6 FS-2570 For DSC For DSC routine distress Antenna Coupler PREAMP PREAMP FAX-5 AT-1560-25 FAX-5 LOUDSPEAKER SEM-21Q NAVIGATOR RX BOARD CONTROL UNIT HANDSET FS-2570C HS-2001 INCOMING INDICATOR PRINTER IC-303-DSC NBDP CONTROLLER PP-510 TRANSCEIVER IB-581 UNIT FSC-2570T NBDP TERMINAL UNIT PRINTER IB-583 TELEX DISTRESS INTERFACE ALERT BUTTON...
  • Page 7 EQUIPMENT LISTS Standard Supply Name Type Code no. Remarks FS-1570T For FS-1570 (150 W) Transceiver Unit FS-2570T For FS-2570 (250 W) Control Unit FS-2570C AT-1560-15-AAS For FS-1570, Resin AT-1560-15-SUS For FS-1570, Stainless steel Antenna Coupler AT-1560-25-AAS For FS-2570, Resin AT-1560-25-SUS...

  • Page 8: Optional Equipment

    Optional Equipment Name Type Code no. Remarks PR-300 For FS-1570 (150 W) AC-DC Power Supply Unit PR-850A For FS-2570 (250 W) w/installation materials (CP16-01200), Printer PP-510 1 set accessories (FP16-00100) Printer Interface Kit IF-8500 000-053-895 Distress Alert Unit IC-302-DSC 1 set...

  • Page 9: Mounting

    1. MOUNTING Control Unit 1.1.1 Mounting methods The control unit can be mounted one of four ways; • In the hanger (overhead, bulkhead or tabletop) • Flush mounting. 1.1.2 Mounting considerations • Make sure the location is strong enough to support the unit under the conditions of continued vibration and shock normally encountered on the boat •...

  • Page 10: Flush Mounting

    1.1.4 Flush Mounting Use the optional flush mount kit. Name: Flush mount kit Type: OP05-98 Code No.: 005-951-830 Name Type Code No. Remarks Mounting metal 05-089-1171 100-299-020 Wing bolt M4x30 000-804-799 Wing nut 000-863-306 Hex. bolt M6x12 000-862-127 Spring washer 000-864-260 1.

  • Page 11: Antenna Coupler

    Antenna Coupler DANGER ELECTRICAL SHOCK HAZARD Do not touch cable from the antenna coupler. Electric shock, fire, serious injury or death can result if the cables are touched during transmission. DANGER Do not touch this point. 1.2.1 Introduction The antenna coupler is installed between the antenna and the transceiver, and tunes the antenna to the transmitter.

  • Page 12: Mounting Considerations

    Grounding Run a copper strap (supplied) between the ground terminal of the antenna coupler and the ship’s superstructure. Ground plate Copper strap (a piece of steel plate) Solder 0.4 x 50 x 600 Braze For outdoor installation, Weld to ship's structure apply a coat of paint to prevent rust.
  • Page 13 Indoor installation • Locate the unit away from GPS and radio equipment to avoid mutual interference. • The lead-in wire should be as near to the unit as possible. • Select a place where the unit can be easily maintained, but where it will not interfere with crew or passengers.
  • Page 14 1.2.5 Mounting The antenna coupler can be fixed to the floor, bulkhead, overhead or mast. For mounting on the bulkhead, fix the coupler with either tapping screws or M5 bolts and nuts. The resin type antenna coupler can be mounted on the most, using two U-bolt (Type: OP05-12, Code No.: 005-923-680).
  • Page 15 Mast Mast Drain Drain tube Tube Ground Terminal Ground For thin bulkhead Copper Earth terminal U-bolt use nuts, bolts and Plate Assy. washers instead of Coaxial tapping screws. For thin bulkhead, use Cable Ground Signal nuts, bolts and washers U-bolt plate (copper) Cable instead of tapping screws.

  • Page 16: Transceiver Unit

    The location must be clean and dry. • The mounting location must be able to support the weight of the unit (FS-1570: 11.0 kg, FS-2570: 14.0 kg) under the continued conditions of vibration normally encountered aboard the vessel. If necessary, reinforce the mounting location.

  • Page 17: Handset (W/Bracket)

    Handset (w/bracket) Unfasten six screws to remove the bracket cover, and fasten the bracket to the mounting location with two tapping screws 4 x 16 (supplied) on the desktop or bulkhead. Note: The magnet inside the bracket may pull the screwdriver when mounting the hanger. (77) Handset hanger cover...

  • Page 18: The Antenna

    Locate the insulator away from funnels and masts. • If the antenna coupler is installed outdoors, use a lead-in insulator (Furuno type YA-150 for FS-1570 or YA-218 for FS-2570) to make the connection. If necessary, use a high quality antenna switch and stand-off insulator. •...

  • Page 19: Mounting Of Optional Equipment

    1.6 Mounting of Optional Equipment 1.6.1 AC-DC power supply unit Mounting considerations When selecting a mounting location, keep in mind the following points. • Select a location which provides adequate ventilation. • The location should be clean and dry. • The mounting location must be able to support the weight of the unit (PR-300:14.5 kg, PR-850A: 35 kg) under the continued conditions of vibration normally encountered aboard the vessel.
  • Page 20 Thread (14 threads/inch) 1" Pipe 2.6m Whip Antenna Spring Washer Mast Hose Clamp Earth Coupling Antenna Wire Wire Antenna Fixture Preamp Unit Mounting of preamp unit 1.6.3 Printer PP-510 Install the unit with the two mounting fixtures (supplied). Refer to the outline drawing at the end of this manual.
  • Page 21 1.6.4 Distress alert unit IC-302-DSC/Incoming indicator IC-303-DSC Select the mounting location where the button on the unit can be operated easily in an emergency. See the back of the manual for mounting dimensions and recommended clearance space. (Compass safe distance: Standard, 0.8 meters, Steering, 0.6 meters) 1.
  • Page 22 This page is intentionally left blank. 1-14...

  • Page 23: Wiring

    D.ANT(W/R 1) opener set the opener in a FS-2570C terminal. While pulling the opener downward, insert the core. core HS-2001 3. Release the opener. Tug on the core to Ground Wire Printer confirm it is inserted Speaker properly. Wiring (FS-1570)
  • Page 24 TB-2 To ANTENNA 1 ANT TUNE OK THROUGH TUNE DUMMY + 15V Ground Replace this rubber sleeve with one supplied with drain wire. accessories if using a coax cable whose diameter is Ground Signal cable larger than supplied one. terminal Coaxial cable Connect to ground to prevent interference and electrical shock.
  • Page 25 TB1 and 2. Fasten it to the fixing plate at cable entrance with a cable tie (local supply.) When connecting to the optional AC-DC power supply unit PR-300 (FS-1570) or 850A (FS-2570), supply AC power and DC power to the PR-300/850A. See paragraph “2.3 Connection of AC-DC Power Supply Unit”...
  • Page 26 Note1: How to connect cable to the terminal board. 1. Press this downward by finger or screw driver. 2. Insert a core of cable. 3. Release the finger or screw driver. Control unit Connect the transceiver unit and the control unit by the supplied cable with D-sub 15 pin connector for both ends.

  • Page 27: External Equipment

    9 10111213141516 RCV BZ 05P0731 17181920 21222324 252627282930 3132 IEC61162 Distress alert unit* 9 mm 9 mm IC-302-DSC Incoming indicator IC-303-DSC Navaid Distress message controller* External BK DMC-5 CO-SPEVV-SB-0.2x5P CO-SPEVV-SB-0.2x2P TTYCS-4 *Select one. T-IF Board (FS-1570) Connection of external equipment...
  • Page 28 IEC61162-1 (NMEA) equipment Connects a navigator to the terminal box in the transceiver unit. The FS-1570/2570 can receive the following sentences in IEC-61162-1 (ed.2nd) format. Use the interconnection cable type CO-SPEVV-SB-C 0.2x2P (option). • GLL: Latitude and longitude • RMC: Generic navigation information •...
  • Page 29 Note: When GND line from other radiotelephone is connected to the chassis, float the ground. T-IF Board (05P0731) 24V TB1 External Battery BK GND BK (+) Power of BK FS-1570/2570 Receiver T-IF Board (05P0731) TB5 BK (+) 17 Relay TX KEY BK GND Example of connection with receiver...
  • Page 30 Transceiver unit FS-1570/2570 T-I/F Board (05P0731) TB5 BK(+) 17 Power for relay TX KEY -BK line RX MUTE BK GND Example of connection with Tx/Rx unit MIF unit (future addition) Use 17JE-13250-02 connector (supplied as installation materials) to connect MIF unit to REMOTE port on transceiver unit.

  • Page 31: Connection Of Ac-Dc Power Supply Unit (Option)

    When connecting to an AC and DC ship’s mains, the optional AC-DC power supply unit PR-300 (FS-1570) or PR-850A (FS-2570) is required. Attach the crimp-on lug FV5.5-S4 (local supply) to the power cable (local supply) for connection with the power supply unit.
  • Page 32 2.3.1 PR-300 for FS-1570 Both 100/110/200/220 VAC and 24 VDC are supplied to the AC-DC power supply unit PR-300. When AC input fails, DC power is supplied. Changing tap connections The transformer tap for input voltage has been set to 220 VAC (fuse 5A) at the factory.
  • Page 33 2.3.2 PR-850A for FS-2570 Both 100/110/120/200/220/240 VAC and 24 VDC are supplied to the PR-850A. When AC input fails, DC power is directly supplied. For GMDSS vessels, 24 VDC power must be supplied through the radio battery. Wiring Connect cables to the input terminal on the front panel, using crimp-on lugs. Selection of input voltage The input voltage is adjustable for 100/110/120/200/220/240 VAC, and is factory-set for 220 VAC.
  • Page 34 100VAC input 110VAC input White White Black White Black Black Black White Black Black 120VAC input 200VAC input White White Black Black White Black Black White Black Black (Default setting) 220VAC input 240VAC input White White Black Black Black White Black White Black...

  • Page 35: Initial Setting

    3. INITIAL SETTING After completing the installation, check the all connection before applying the power. Performance Check Receiver 1. Set the unit as follows. a) Speaker: ON b) Squelch: OFF c) AGC: FAST d) Sensitivity: Max 2. Confirm that a signal can be received on each band. If noise or signal is weak, check the antenna lead-in section, coaxial cable connection and ground connections.
  • Page 36 4. Press the [LOG/TUNE] key. “TUNE” appears on the LCD. “TUNING: OK” appears when tuning is completed. Record the status (on or off) of LEDs CR1 – CR22 (on the COUPLER Board). 5. Set S1 switch to MANUAL. 6. Set S4, S5, S6 DIP switches so that LEDs become the status is the same as in step 4. The relations between the DIP switch and LED are shown on the next page.

  • Page 37: System Setup

    : 100 REGULATION : INTL PANEL 1 2002-07-24 07:21:43 PROTECTION : ON System setup menu (Protection: on) 4. Enter the password referring to appropriate FURUNO INFORMATION. System Setup MMSI : LINE OUT : +0.0 WATCH RCVR : MF/HF CH DET S LEVEL...
  • Page 38 3.3.2 Line out level for DSC signal setting Set line out level. For FURUNO SSB (600 Ω), set 0 dBm. 1. On the System setup menu, rotate the [ENTER] knob to select “LINE OUT”. 2. Press the [ENTER] knob. LEVEL (-4.5 ~ +4.5) DBM +00.0...
  • Page 39 3. Rotate the [ENTER] knob to adjust the indicator bar. Too low a setting stops transmission of a DSC message because it detects noise on the DSC frequency. Alternately, too high a setting transmits the DSC message though low signal level is present on the DSC frequency used.
  • Page 40 3. Enter the password referring to the appropriate FURUNO INFORMATION. System setup System setup System setup REGULATION : INTL TX POWER (FREQ) ENABLENB : OFF TX FREQ : FREE TX POWER (USER CH) TX TUNE : ON RX FREQ : FREE...
  • Page 41 3.3.7 System setting of RT Set the RT similarly with DSC. Do the setting at System setup menu at the transceiver unit. System setting (RT) Item Description Setting REGULATION Selects the national regulation to change INTL, RUSSIA, USA, THAI the frequency, user channel, etc. TX FREQ Selects the frequency to transmit.
  • Page 42 3.3.8 Setting of Tx power Set the Tx power at Tx power setup menu. Tx power setup Item Description Setting TX MODE Select the radio band to set the power of transmitting. SSB: Modulated in 1785 Hz TLX: Common with DSC, modulated in 1785 Hz TX FREQUENCY Select the frequency to set the power of transmitting.
  • Page 43 After the setting Tx power, save it as below. 1. Rotate the [ENTER] knob to select “SAVE TX POWER”. Tx power setup TX MODE : SSB TX FREQUENCY : 2182.0HZ TX POWER : HIGH TX POWER ADJ : 240 : 100 TX POWER TUNE SAVE TX POWER ERASE TX POWER...

  • Page 44: Setting Dip Switches

    Setting DIP Switches Location of DIP Switches CPU Board (05P0732) 3.4.1 IEC (NMEA)/DMC/MIF data receiving line (S2) IEC (NMEA) RS-422 Current Loop S2-#1 RS-422 Current Loop S2-#2 RS-422/232C Current Loop RS-422 RS-232C S2-#3 S3-#1, 2 S3-#3, 4 Note: S2-#4 is no used. 3.4.2 Incoming indicator IC-303 3-10...

  • Page 45: Preamp Setting (For Fax-5)

    3.4.3 Connection to DMC-5, IC-302-DSC The above equipment can be connected to the DMC port at the back of the main unit. For these units, set DIP switches as below. Set to RS-422 as follows. IC-302-DSC Set to Current Loop for IC-302 connection. Preamp Setting (For FAX-5) When using the preamp for the watch receiver antenna, set J3 on the W/R Board to ACTIVE in the transceiver unit.
  • Page 46 This page is intentionally left blank. 3-12...

  • Page 47: Option Kit

    4. OPTION KIT DSC Routine Frequency Board For FS-2570, the W/R Board 05P0734 (option) enables reception of DSC routine frequencies without the SSB radiotelephone connection. For complete modification, the whip antenna for DSC routine frequency is necessary. • Necessary Parts :W/R2 Board Kit, Type :OP05-99, Code No.
  • Page 48 How to use SSB antenna for DSC routine frequency receive To use the SSB radiotelephone antenna for routine watch keeping, the following modification is necessary. On the TX_FIL Board (05P0736) 1. Attach the jumper wire to JP1 on the TX-FIL board. 2.

  • Page 49: Connecting Of Nbdp Terminal Unit

    4.2 Connecting of NBDP Terminal Unit OP05-96 (IB-581)/OP05-100 (IB-583) To use this equipment for the telex, the NBDP terminal unit is required. Name: NBDP terminal set, Type: OP05-96, Code No.: 000-056-949 Name Type Code No. Remarks Terminal unit IB-581-02 000-043-350 1 set w/installation materials DSP Board...
  • Page 50 4. Use the 17JE-573-10 to connect the NBDP port of the control unit and COM1 port of the NBDP terminal unit. Keyboard 1. Attach the labels for NBDP and the compass safe distance to the appropriate locations shown below. Label for key operation for FUNCTION KEYS (supplied) LABEL FOR COMPASS SAFE DISTANCE (supplied)
  • Page 51 A - 1 ＰＡＣＫＩＮＧ　ＬＩＳＴ ＰＡＣＫＩＮＧ　ＬＩＳＴ ＰＡＣＫＩＮＧ　ＬＩＳＴ ＰＡＣＫＩＮＧ　ＬＩＳＴ 05DZ-X-9851 -0 FS-2570C FS-2570C FS-2570C FS-2570C N A M E DESCRIPTION/CODE № O U T L I N E Q'TY ユニット ユニット ユニット ユニット UNIT UNIT UNIT UNIT 操作部 FS-2570C CONTROL UNIT 000-056-946 工事材料...
  • Page 52 A - 2 005-952-180 05DZ-X-9402 CODE NO. CODE NO. CODE NO. CODE NO. TYPE TYPE TYPE TYPE CP05-08802 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名　　称 型名／規格 数量 略　　図 用途／備考 Q'TY OUTLINE NAME DESCRIPTIONS REMARKS ｺﾈｸﾀ(17JE) 17JE-13250-02(D8C) CONNECTOR CODE NO. 000-119-318 +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ　1種...
  • Page 53 A - 3...
  • Page 58 A - 8...
  • Page 60 A - 10...

This manual is also suitable for:

Fs-2570

Table of Contents