Viper Fang 18C Owner's Manual
  1. Manuals
  2. Brands
  3. Viper Manuals
  4. Floor Machine
  5. SCRUBBER FANG 18C
  6. Owner's manual

Viper Fang 18C Owner's Manual

Semi-auto scrubbers
Hide thumbs Also See for Fang 18C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fang 18C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Viper Fang 18C

Summary of Contents for Viper Fang 18C

  • Page 3 SAFETY PRECAUTIONS This machine is intended for commercial use. It is constructed for use in an indoor environment and : Flammable materials can cause an is not intended for any other use. Use only with explosion or fire. Do not use flammable materials recommended accessories.

  • Page 4: Machine Set Up & Installation

    the squeegee bracket. (the wheels on the squeegee point to the back) 2. Tighten the knobs securely. MACHINE SET UP & INSTALLATION UNPACK MACHINE FILLING THE SOLUTION TANK Be sure and check packing carton for any damage. Immediately report any damage to carrier. Be 1.

  • Page 5: While Operating Machine

    Adjust solution flow by adjusting the position 1. Remove the drain hose from the holder, and of ball valve knob. place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. WHILE OPERATING MACHINE 2.

  • Page 6: Vacuum Motor Maintenance

    & remove the drain hose from the holder prior to removing the recovery tank when performing maintenance. VACUUM MOTOR MAINTENANCE 1. Contact your local Viper Distributor for any motor maintenance. 2. Check the vacuum motor brushes every 250 hours, Replace the brushes when they are worn to a length of 10mm or less.
  • Page 7 BASIC TROUBLESHOUTING PROBLEM CAUSE SOLUTION The wiring not connected correctly or Check the wiring or contact Viper Distributor bad wiring No Power Bad brush motor Contact Viper Distributor Carbon brushes worn out Contact Viper Distributor The wiring not connected correctly or...

  • Page 8: Technical Specifications

    Technical Specifications: Efficiency 1100m . a i z i t i t a...
  • Page 10 PART DESCRIPTION NUMBER REQ'D VF80111 FILTER, CLEAR DOME VF82139 “O” RING VF80113 FILTER VV20501 SCREW, PH, SST, M5 X 14 VV13654 WASHER, SST, M5 VF80112 MOUNTING BASE, FILTER VF82090 CLAMP, HOSE VF80349 HOSE, INLET, FILTER VF13521 NUT, M6 VF13533 WASHER, M6 VV13607 WASHER, LOCK, M6 VF13495...
  • Page 11 PART DESCRIPTION NUMBER REQ'D BARB, HOSE, 90° DEG VF81403 VF14255 SET SCREW, M12 X 65 VF80262 VF80262 SPRING WIRE SPRING WIRE VF80219 SHAFT, DRIVEN PULLEY GT13015 SCREW, HEX SOCKET, M6 X 30 VF14400 SCREW, ST, M4.2 X 13 VF13502 NUT, NYLON INSERT, M6 VF14225A SCREW, FH, M6 X 40 VF13535...
  • Page 13 PART DESCRIPTION NUMBER REQ'D VF82010 CLEAR COVER,RECOVERY TANK VF82010B GASKET,CLEAR DOME VA13483 WASHER, PLAIN, M4 VA13477 SCREW, ST, M4.2 X 16 VF80343A MODEL DECAL, RIGHT " " ZD55000A VACUUM MOTOR, 110V VF80357 HEAT RESISTANCE COVER VF13533 WASHER, PLAIN, M6 VF13502 NUT, NYLON INSERT, M6 VF13514A WASHER, PLAIN, M8...
  • Page 15 PART DESCRIPTION NUMBER REQ'D VF81408 ADJUSTING PLATE VF13535 WASHER, PLAIN, M8 VF13519 WASHER, LOCK, M8 VV13604 BOLT, M8 X 20 VF81710 ADJUSTING SCREW VF80322 PIN, HANDLE LOCK VF80323 TUBE, HANDLE ADJUSTMENT VF81716 SPRING VF80317BD LEVER, SWITCH, LEFT VV13650 SCREW, PH, M4 X 10 VF81712 SPRING VV13652...
  • Page 17 PART PART DESCRIPTION NUMBER REQ'D VF81222 SCREW, HEX SOCKET, SHOULDER, 5/16 X 1.25" " VF13535 WASHER, PLAIN, M8 X M20 X 2 VV20203 NUT, NYLON INSERT, 5/16" VF82121 VF82121 KNOB, M6 KNOB, M6 VF82118 BACK UP STRIP, SQUEEGEE, FRONT VF82062 BLADE, SQUEEGEE, FRONT "...

Table of Contents