Related Manuals for Viper SCRUBBER FANG 18C
Summary of Contents for Viper SCRUBBER FANG 18C
- Page 1 SCRUBBER USER MANUAL Model: FANG 18C VIPER CLEANING EQUIPMENT CO., LTD Address: Liangbian village, Liaobu town, Dongguan city, Guangdong Province, CHINA...
-
Page 2: Table Of Contents
INTRODUCTION ..2 MANUAL PURPOSE AND CONTENTS ... 2 TARGET... 2 HOW TO KEEP THIS MANUAL... 2 DECLARATION OF CONFORMITY ... 2 IDENTIFICATION DATA... 2 OTHER REFERENCE MANUALS... 2 SPARE PARTS AND MAINTENANCE... 2 CHANGES AND IMPROVEMENTS ... 3 OPERATION CAPABILITIES ... 3 CONVENTIONS ... -
Page 3: Introduction
All necessary operating, maintenance and repair procedures must be performed out by qualified personnel or by Viper Service Centers. Only original spare parts and accessories must be used. Contact Viper for service or to order spare parts and accessories, specifying the machine model and serial number. -
Page 4: Changes And Improvements
CHANGES AND IMPROVEMENTS Viper constantly improves its products and reserves the right to make changes and improvements at its discretion without being obliged to apply such benefits to the machines that were previously sold. Any change and/or addition of accessories must be approved and performed by Viper. -
Page 5: General Instructions
Regularly check the power supply cable for damages, cracks, cuts, etc. If the power supply cable is damaged, replace it immediately. – To avoid any risk, if the power supply cable is damaged, contact Viper Service Center or a qualified technician. –... - Page 6 • is wet or has been dropped into water turn it off immediately and contact Viper Service Center or a qualified technician. – If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.
-
Page 7: Machine Description
ENGLIS USER MANUAL MACHINE DESCRIPTION MACHINE STRUCTURE 1. Solution Tank 2. Recovery Tank 3. Clear Cover 4. Control Box 5. Switch lever 6. Drain Hose 7. Vacuum Hose 8. Water Hose Squeegee Assembly Transport Wheels 11. Bumper 12. Skirt 13. Brush Motor Switch 14. -
Page 8: Accessories/Options
ACCESSORIES/OPTIONS In addition to the standard components, the machine can be equipped with the following accessories/options, according to the machine specific use: 1．Brush 2．Pad driver For further information concerning the optional accessories, contact an authorised Retailer. TECHNICAL DATA Model Solution Tank Capacity Recovery Tank Cleaning Path Pad Pressure... -
Page 9: Wiring Diagram
ENGLISH USER MANUAL WIRING DIAGRAM FOR FANG 18C FANG 18C 80188EU(1)2009-01... -
Page 10: Use
SCRUBBER SETUP NOTE Read operators manual thoroughly prior to operating or servicing this machine!!! a) PRE-OPERATION CHECKS 1. Sweep the outside of the machine. 2. Make sure the voltage of machine conform to local voltage. (220-240V) 3. Check that squeegee is properly installed. 4. -
Page 11: Basic Operation
ENGLISH USER MANUAL BASIC OPERATION WARNING! Do not operate machine unless you have read and understand this manual. 1. Adjust control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. -
Page 12: Draining Tanks
DRAINING TANKS a) DRAINING SOLUTION TANK NOTE Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain. -
Page 13: Maintenance
VACUUM MOTOR MAINTENANCE 1. Contact your local Viper Distributor for any motor maintenance. 2. Check the vacuum motor brushes every 250 hours, Replace the brushes when they are worn to a length of 10mm or less. -
Page 14: Brush/Pad Cleaning
BRUSH/PAD CLEANING CAUTION! It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris. 1. Remove the brush/pad from the machine, as shown in Use chapter. 2. Clean and wash the brush/pad with water and detergent. 3. -
Page 15: Troubleshooting
Vacuum motor is loose Recovery tank lid is loose Recovery tank is full Float shut off is clogged FANG 18C CAUSE Check the wiring or contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Check the wiring or contact Viper Distributor... -
Page 16: Storage
STORAGE WARNING! If you are storing the machine in an area which can freeze, be sure both tanks and the solution plumbing are empty of all water and dry! 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3.