Skyrc T6755 Instruction Manual page 7

OPERATION PROGRAM
allowed Max Rate is adjustable independently, so the Battery Capacity setting mainly
provides additional safety monitoring.
Touch the arrow and to select the charge/discharging current if you want to modify.
CAUTION! BE SURE you know what Charge/Discharge Current setting to use for your
battery.
3. Charging Program
Depends on different battery type, the operation programs are different.
Batt Operation
Type Program
This charging mode is for charging LiPo/LiFe/LiIon battery in normal mode.
CHARGE
This mode is for discharging LiPo/LiFe/LiIon battery.
DISCHARGE
This program is for charging or discharging lithium battery which will not be
STORAGE
used for long time.
LiPo
Lilon
The charging capacity may be a bit smaller than normal charging but the
FAST CHG
LiFe
process time will be reduced.
This mode is for balancing the voltage of lithium-polymer battery cells while
charging.
BAL CHARGE
Note: We recommend charging lithium batteries with a balance wire
in the balance mode only.
The user can check lithium battery's total voltage, the highest voltage, the
VOLT METER
lowest voltage and each cell's voltage.
The charger will charge NiMH and NiCd batteries using the charge current
CHARGE
set by the user.
In this program the charger detects the condition of the battery which is
connected to the output and automatically charges the battery.
Note: you should set up the upper limit of the charge current to avoid
AUTO CHG
damage by excessive feeding current. Some batteries of low
resistance and capacity can lead to higher current.
DISCHARGE This mode is for discharging NiMH/NiCd battery.
NiMH
NiCd
In re-peak charge mode, the charger can peak charge the battery once,
twice or three times in a row automatically. This is good for confirming the
RE-PEAK
battery is fully charged, and for checking how well the battery receives fast
charges.
1 to 5 cyclic and continuous process of charge>discharge or
discharge>charge is operable for battery refreshing and balancing to
CYCLE
stimulate the battery's activity.
The user can check Nickel battery's total voltage.
VOLT METER
CHARGE This mode is for charging Pb battery.
This mode is for discharging Pb battery.
DISCHARGE
Pb
VOLT METER The user can check Pb battery's total voltage.
Please touch the arrow ▲and ▼ to find the desired operation program and the selected
one will be framed.
10
Description
T6755
4. Program Start
Touch start button or touch and hold
the program.
And the charger will detects battery cells automatically. If the detecting result and your
setting are identical, the charger will start working automatically.
LiPo 6S C6.0A / D2.0A P1
BATT TYPE OPERATION
Pb FAST CHG
LiPo BAL CHARGE
Lilon VOLT METER
CELLS CAPACITY SETTING PRESET START
mAh
E.TEMP=External Temperature
(Battery Temperature)
Temperature probe must be
attached to the charger
I.TEMP=Charger's Internal Temperature
If the setting is wrong, it will shows the error message which is not matching your battery
parameter and you have to touch HOME to back to homepage to re-set the parameter
before going ahead.
LiPo 6S C6.0A / D2.0A P1
BAL CHARGE
CHECK BATTERY ... ERROR
CELL NUMBER ERROR
HOME
T6755
OPERATION PROGRAM
the framed operation program for 3 seconds to start
LiPo 6S C6.0A / D2.0A
BAL CHARGE
CHECK BATTERY... OK
LiPo 6S C6.0A / D2.0A
BAL CHARGE
VOL 16.7V :
CAPACITY: 40mAh
TIME 00 02 00 : : : E.TEMP 0 C
CURRENT 2 0A : . I. TEMP 36 C
BALANCE
GRAPH
STATUS
LiPo 6S C6.0A / D2.0A
BATT TYPE OPERATION
Pb FAST CHG
LiPo BAL CHARGE
Lilon VOLT METER
CELLS CAPACITY SETTING PRESET
mAh
P1
P1
:
:
STOP
P1
START
11