Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Logic Controls LR3000
Summary of Contents for Logic Controls LR3000
- Page 2 Logic Controls has been negligent regarding the design or manufacture of the product. Logic Controls shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as original Logic Controls...
-
Page 3: Table Of Contents
LR3000 Thermal Printer. Revision 1.0 Contents Preface....................6 Who should read this manual?................6 How this manual is organized? ................. 6 Related publications and software..............6 Where to find more information ............... 6 EMC, Safety and Other Applicable Standards........7 FCC Compliance Statement ................ - Page 4 User’s Manual Chapter 2 ................... 13 Setting Up Your Product ................... 13 2.1. Installing ......................13 2.1.1. Plugging in the Power Adapter ..............14 2.1.2. Turn on Your Product ................. 15 2.1.3. Inserting or Changing the Paper Roll............15 2.1.4. Connecting the Communication Cables ............
- Page 5 LR3000 Thermal Printer. Revision 1.0 Chapter 3 ................... 29 How to Use Your Product..................29 3.1. User Interface ....................29 3.1.1. Buttons....................... 29 3.1.2. LEDs ......................30 3.2. Operation Modes..................... 30 3.2.1. Normal Mode ....................30 3.2.2. Other optional modes ................. 30 3.2.2.1.
-
Page 6: Preface
User’s Manual Preface This manual assists you with the installation, configuration and usage of this Logic Controls product. 1. Who should read this manual? This manual is intended for use by persons who are installing, using or testing the product. -
Page 7: Emc, Safety And Other Applicable Standards
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Logic Controls is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. -
Page 8: Rohs
User’s Manual 6. RoHS This product complies with the RoHS 2002/95/EC Directive from the European Community. 7. UL This product was tested and was certified with the cULus mark, for Canada and USA, by the UL60950 standard. 8. NOM-019-SCFI-1998 This product complies with the Mexican Official Standard NOM-019-SCFI-1998 – Safety for Data Processing Equipment. -
Page 9: Safety Information
(including water or other liquid) falls into the equipment. Continued use may damage it or lead to fire *. - Please contact your dealer or a Logic Controls service center for advice. - Never attempt to repair this product yourself. Improper repair work can be dangerous. -
Page 10: Chapter 1
If any parts are missing or damaged, please contact your dealer for assistance. 1.1.1. Introduction The LR3000 is a fast high quality POS printer using the thermal technology for printing, being compatible with most cash systems on the market. The printer can be used with banking equipment, computer peripheral systems, ECR and POS systems. -
Page 11: Product Characteristics
CODE129, ITF, CODABAR, UPC-A, UPC-E, ISBN, MSI, PLESSEY, PDF-417) - Complete drivers for Windows including Spooler Driver, APIs. - Easy configuration and remote management by Logic Controls User Utility Software application - Bitmap Image Buffer, for uploading logos to the printer’s internal non-volatile memory... -
Page 12: Optional Items And Accessories
RS-232 Serial Interface Module (DB25 connector) RS-232 Serial Interface Module (DB9 connector) USB Interface Module Ethernet Interface Module DB25-DB9 serial interface cable DB9-DB9 serial interface cable USB interface cable Power adapter * Please contact Logic Controls for the availability of interface modules and accessories. -
Page 13: Chapter 2
LR3000 Thermal Printer. Revision 1.0 Chapter 2 Setting Up Your Product 2. Installing 2.1. Installing Here you can see the main parts of this printer. Spacer (inside the printer) *Shipped only with part number LR3000R... -
Page 14: Plugging In The Power Adapter
User’s Manual Where to place the printer WARNING! The LR3000 should be placed on a plain, stable surface located indoors or protected from the weather. Avoid enclosing the printer or keeping it obstructed. Connections It is possible to connect up to three cables to the printer. All connections are placed at the back of the printer (there can be different connections depending on the configuration of the Printer Interface Board). -
Page 15: Turn On Your Product
LR3000 Thermal Printer. Revision 1.0 2.1.2. Turn on Your Product Turn on the printer using the On/Off Switch, located on the left side of the printer, and check if the Power ON LED is lit. The printer will initialize and indicate the printer status ( ). -
Page 16: Connecting The Communication Cables
Verify On/Off Switch and make sure the printer is turned off. WARNING! The printer is configured by factory default to work with Logic Controls Cash Drawers. The printer configuration is usually compatible with many Cash Drawers in the market. If you are not sure of this compatibility, do not connect the cash drawer cable and verify the printer’s... -
Page 17: Configuring
End Paper Sensor, paper width, Command Set and Print Mode. (¹) The "Paper Width” can be altered only if the "Command Set " is configured as "LOGIC CONTROLS." To enter the Printer Menu you have to switch off the printer and switch on again with the FEED BUTTON ( ) pressed. -
Page 18: Print Density Configuration
User’s Manual 2.2.2. Print Density Configuration In this section, you can configure the print density of all printed information. This configuration is very important when you use different paper thicknesses. You can configure to Normal, Strong, Very Strong, Very Weak or Weak Print Density. The factory default setting is Normal. -
Page 19: Adjusting The Paper Width
LR3000 Thermal Printer. Revision 1.0 2.2.6. Adjusting the Paper Width To adjust the paper width simply pull the spacer up and insert it in the desired position, according to the paper width desired. The figure below helps to identify the correct position, in compliance with the paper width. -
Page 20: Rs-232 Serial Interface (Db-25/Db-9 Connector)
230400 baud rate. 2.3.2.2. Dip Switches By turning on the printer while pressing the Cut button, the LR3000 will print a Quick Reference Table with the LED Error Codes and a Table with Dip Switch Configuration for the serial interface. - Page 21 LR3000 Thermal Printer. Revision 1.0 1 2 3 4 5 6 7 8 Serial Dip Switch table DEFAULT 1 2 3 4 5 6 7 8 DIP SWITCH LENGTH DIP SWITCH BAUD RATE 7 BITS 1200 1 2 3 4 5 6 7 8...
-
Page 22: Cable Connection
User’s Manual 2.3.2.3. Cable Connection Here you can see the Cable connections for both connectors; the pins are compatible with an IBM-PC. Signal Direction Description RING Output Power Supply (+5 VDC) Ind. Data reception. The data for the Input printer will be received in this pin. Data transmission. -
Page 23: Usb Interface
The communication port is fixed and it is configured with the number 9100. This value cannot be modified. To change the IP address and the net mask of the printer use the user's software. You can download the User's Software on Logic Controls website: www.LogicControls.com... -
Page 24: Installation Procedures
User’s Manual 2.3.4.2. Installation Procedures 1. On the PC/POS, go to Local Area Connection and select "Properties"; 2. Go to Internet Protocol (TCP/IP) and double click it;... - Page 25 LR3000 Thermal Printer. Revision 1.0 3. Change the IP address and subnet mask according to the picture below; 4. Execute Logic Controls driver installation and select "Ethernet" interface and type in the IP as follow.
-
Page 26: Test Procedures
User’s Manual 2.3.4.3. Test Procedures 1. Run Logic Controls User Software and select "Ethernet" interface. Type in the IP address as shown below and press "apply"; 2. Go to "Status", press "Activate" and check printer status with LED indicator;... -
Page 27: Cable Connection
LR3000 Thermal Printer. Revision 1.0 3. Go to "Printing" and type in some text to print. 2.3.4.4. Cable connection 8 7 6 5 4 3 2 1 10/100 Mbps LED Link LED Male Male RJ-45 RJ-45 Signal ATTENTION! The configuration of this cable is to connect the printer to a Hub or Switch. -
Page 28: Cash Drawer Interface
You will find the jumpers in the area shown by the picture below. The drawer connector pin layout is described below: Drawer configuration Drawer type Logic Controls/Epson (B-D) ** Others (A-C) Drawer open/close signal Drawer kick out signal Drawer kick out signal... -
Page 29: Chapter 3
LR3000 Thermal Printer. Revision 1.0 Chapter 3 How to Use Your Product 3.1. User Interface This printer has two LEDs to indicate the printer’s status and two buttons for simple operation. 3.1.1. Buttons Feed: Press this button to feed paper in continuous mode. This function can be modified by commands and the button can be disabled. -
Page 30: Leds
To start the self test you only have to wait a few seconds without doing anything after you are in the Printer Menu. The printer will print a sample ticket with a list of features of your LR3000, followed by a full cut. 3.2.2.2. Configuration Mode... -
Page 31: Dump Mode
The User Utility software is a Windows-based application that has several basic and advanced functions for the LR3000 printer. It can be used to test the behavior of several settings in the printer, and to print in many different ways, with different resources;... -
Page 32: Cutter
User’s Manual small paper particles from the sensors, use a small brush to wipe off the dust and paper particles. Do not attempt to use liquids to clean the sensors, in order to avoid damage. 3.4.3. Cutter The cutter is manufactured with hardened steel for maximum wear resistance. It is normal to have some dust buildup in the blades and this will not affect cutter performance. -
Page 33: Chapter 4
Check the command set that the printer are configured. You can configure to Logic Controls or ESC/POS The communication cable has Check for a good connection between the printer one or more lines with faulty and the host or change the communication cable. - Page 34 User’s Manual Problem Possible Cause Procedure CAUTION! Do not touch the print head; let it cool down before touching, as it can be very hot after printing. The paper does not get out Switch off the printer and open the cover. Paper jam the printer.
-
Page 35: Chapter 5
Dimensions: 146 mm (height) x 150 mm (width) x 218 mm (depth) Characteristics Mass: 1.2 kg Software and Drivers Windows XP™, User’s Software. Available Power Supply, Communication Cable. Accessories (1) Please contact Logic Controls to consult the availability of the interfaces and accessories.