Table of Contents
Advertisement
A. FACEPLATE
TIMER FEATURES
_1_ OPTIONAL
SETTINGS
- SALT EFFICIENCY,
CLEAN
FEATURE,
CLEAN FEATURE
MINUTES,
MAXIMUM
DAYS
BETWEEN
REGENERA-
TIONS
and 12 / 24 HOUR
CLOCK:
1. To set any of the following
options,
press
and hold
SELECT
for 3 seconds
until 000 shows
in the display.
Then
press
once until
the SALT EFFICIENCY
dis-
play
shows.
Use the UP / Down
buttons
to change
the ON / OFF displays.
OFF
o
_SALTEFFICIENCY'O
When
this feature
is ON,
the unit will operate
at salt efficiencies
of 4000 grains
of hardness
per pound
of salt or higher,
which
will
reduce
the softeners
salt usage.
(May recharge
more
often
using
smaller
salt dosage
and less water).
2. Press SELECT
again
to show
the CLEAN
display.
UFF
_CLEAN:
This feature
is beneficial
on water
sup-
plies containing
iron and/or
high amounts
of sedi-
ments
(sand,
silt, dirt, etc.). When
set to ON, a back-
wash
and fast rinse
cycle will occur first, preceeding
the normal
regeneration
sequence
(see page
2-4).
This provides
extra
cleaning
of the resin
bed before
it is regenerated
with the salt brine. To conserve
wa-
ter, if your
water
supply
does
not contain
iron or
sediments,
be sure this feature
is set to OFF.
3. Press
SELECT
again
until
the CLEAN
TIME dis-
play
shows.
_es
example: time set to 3 minutes
_CLEANfeature
minutes:
If you are using
this fea-
ture,
the length
of the extra
backwash
cycle auto-
matically
sets to 7 (9minutes
on UltraSoft
250) min-
utes. However,
you can adjust
this time from I to 15
minutes
in length.
To change
this cycle time, use the
UP button
to increase
the time, or the DOWN
button
to shorten
the time. If no change
is desired,
continue
below.
2-2
4. Press
SELECT
again to show
the following
RE-
CHARGE
display.
RECHARG£
_t
default display
example: set to 4 days maxi-
mum between regenerations
_Maximum
days
between
regenerations:
The face-
plate
timer
automatically
controls
regeneration
fre-
quency
(see page
2-5). This provides
the greatest
operating
efficiency,
and under most conditions
this
feature
will be left in its default
mode.
However,
you can
modify
this feature
if you want to force a
regeneration
every set number
of days.
For exam-
ple, if your
water
supply
contains
iron
and you
want
the softener
to regenerate
at least once every
few days to keep the resin bed clean, set the display
as typically
shown
above. Setting
is available
from
1 to 15 days by using the UP and DOWN
buttons.
5. Press
SELECT
to show
the 12 HOUR
display.
_12
or 24 hour clock:
All time
displays
are shown
in standard
clock time (1 to 12 PM; and 1 to
12 AM)
at the 12 hr default
set-
ting. If military
time displays
are
desired,
set to 24 hr by pressing
the UP button.
I
J
riME
6. Press
SELECT
to return
to the present
time dis-
play.
WATER FLOW THROUGH
THE SOFTENER
If soft water
is in use, the water
flow
bars
continually
scroll
across
the
display.
The
bars
scroll slowly
when
water
flow is
slow, and
move
faster
as water
flow increases.
The flow bars do
not
show
when
all faucets
and
water
using
appliances
are off.
=i
2,3B"
Flow bars scroll
when
I_,;
{
_LQ"_
_"
SOft water
is in use
_==1,: _
Problems,
Questions?
Call 1- 800- 426- 9345 Kenmore
Water
Line
Hide quick links:
Advertisement
Table of Contents
