Do you have a question about the Automaid 600 and is the answer not in the manual?
Questions and answers
Shane Ellis
March 1, 2025
The machine turns once and then stop
1 comments:
Mr. Anderson
May 14, 2025
The cause of the Defy 600 machine turning once and then stopping could be related to a water level issue or a power supply problem to the water pump. If the water pump cannot get power and there are no visible loose connections, it may indicate a fault in the control board, wiring, or pump itself. Also, if the machine is not filling with water properly, it may stop early in the cycle. Check the water intake filters for blockages and confirm that the water tap is open and the hose is not kinked.
This answer is automatically generated
Melissa
June 21, 2025
Our machine does not want to work but power button is on
Page 1
PAGE INDEX INSTALLATION • Packaging • Transport fittings • Levelling • Water connection You can rely on Defy • Water drainage • Electrical connection DETERGENT dispenser CONTROL PANEL FEATURES • Detergent dispenser • Temperature control OWNER’S MANUAL • Wash programme selector •...
Thank you for choosing Defy You are now the proud owner of one of the finest and most modern washing machines that today’s technology can pro- duce. You and your Automaid are going to make a great team together. But first it will pay if you really get to know each other.
Levelling 1. The machine must stand firmly on the floor. Any instability will negatively affect its performance. 2. The machine has two adjustable feet at the front. 3. To level the machine, loosen the plastic lock nuts on the adjustable feet. 4.
3. If the power cord should ever need replacing, use only a genuine cord ( Type ‘X’) available from the nearest Defy Service Centre. The appliance must be earthed and the manufacturer and seller do not accept responsibility for any damage due to incorrect electrical connection.
Features 1 Detergent dispenser. The detergent dispenser has 3 compartments. ( See page 4.) Use only low foam detergents specifically designed for front loading automatic washing machines. Dose as per the manufacturer’s recommendations on the detergent pack. Dosage may vary according to wash load, dirt and water hardness. 2 On / Off button.
Features Door Open the door by gently pulling on the handle. Close the door by pushing firmly until it clicks into place. Note: The door locks during the wash cycle Switch the machine off and allow 1 to 2 minutes for the safety lock to disengage.
Programme selection guide PROGRAMME DETERGENT °C LOAD OPTION BUTTONS COMPT RINSE & HOLD NO SPIN COTTON AND LINENS HEAVILY COLD WHITE PRE-WASH A –B-C SOILED To 90 COLD MAIN WASH NORMALLY TO 90 SOILED COLD COLOUR FAST LIGHTLY TO 60 SOILED COLD NON COLOUR FAST...
Operating the machine Sorting the laundry Sort the laundry in one of the following groups: 1. White cotton and linen as well as robust colourfast fabrics. 2. Synthetics and synthetic blends as well as non colourfast fabrics 3. Delicate fabrics such as silks and rayon 4.
Periodically check the inlet and outlet hoses for leaks, perishing or cracks. In very cold conditions water in the hoses may freeze. In this instance, empty the hoses after the wash is complete. Replacement hoses may be purchased from your nearest Defy Service Centre. Page 9...
Care and maintenance Cleaning the pump filter A filter prevents foreign objects from entering and dam- aging the pump. This filter should be cleaned after every 30-40 washes. First disconnect the machine from the power supply. Use a large screwdriver or coin to turn the plastic fasteners in the kick panel through 90°.
Problem washing—Check list Greasy stains on washing. • Use more detergent if washing is heavily soiled. • Use both pre-wash and main wash programmes. • Check that the machine is not overloaded. Grey, dirty looking washing. • Use more detergent if the washing is heavily soiled or if the machine is located in a hard water area.
Page 12
Trouble shooting The machine will not work at all. Check: • House fuses or circuit breakers. • Wall socket ( plug in another appliance to check ) • That the door is closed properly. • That the water tap is open. •...
Service Centres If you have followed the instructions and still have a problem, contact the nearest Defy Service Centre. They will be able to advise you on any aspect of the product or send a qualified technician to repair it.
Warranty This certificate is issued by DEFY APPLIANCES LIMITED manufacturers of Defy and Ocean products, hereinafter the Company, to the original purchaser only, of the appliance described on the certificate and shall constitute the only warranty given in respect of this appliance.
Technical specification Option buttons Temperature selector knob Programme selector knob Detergent dispenser Door Kick-panel Kick-panel securing screw Height 850 mm. Width 600 mm. Depth 540 mm. Net Weight 66 kg. Power requirement 230V, 50 Hz. Nominal current 10 A Power 2250 W Washing speed 70 r/min...
PAGE INDEX INSTALLATION • Packaging • Transport fittings • Levelling • Water connection You can rely on Defy • Water drainage • Electrical connection DETERGENT dispenser CONTROL PANEL FEATURES • Detergent dispenser • Temperature control OWNER’S MANUAL • Wash programme selector •...
Need help?
Do you have a question about the Automaid 600 and is the answer not in the manual?
Questions and answers
The machine turns once and then stop
The cause of the Defy 600 machine turning once and then stopping could be related to a water level issue or a power supply problem to the water pump. If the water pump cannot get power and there are no visible loose connections, it may indicate a fault in the control board, wiring, or pump itself. Also, if the machine is not filling with water properly, it may stop early in the cycle. Check the water intake filters for blockages and confirm that the water tap is open and the hose is not kinked.
This answer is automatically generated
Our machine does not want to work but power button is on