HDY-M60 HDY-M40 20 min 60 min HDY-M60 30 min 60 min 100 min Start 200 min Cool Warm 150 min Please read this manual carefully before operating your dryer. Retain this for future reference. Record the model and serial number of the tumble dryer. Please have this information ready for any service related enquiries.
TABLE OF CONTENTS PAGE IMPORTANT SAFETY INSTRUCTIONS....1 RACK FITTING INSTRUCTION ......12 WIRING CIRCUIT.
IMPORTANT: SAFETY INSTRUCTIONS Warning-To reduce the risk of fire, electric shock, or personal injuries, the following basic precautions should be followed: Read all instructions before using this dryer. 2 The interior of the dryer should be cleaned periodically by qualified service personnel.
Do not dry unwashed items in the tumble dryer. 16 Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. 17 To prevent fire, do not use heat to dry items containing plastic, foam rubber or similarly textured rubber-like materials, or items containing feathers or down.
20 min 60 min HDY-M60 30 min 60 min 100 min Start 200 min Cool Warm 150 min Start button Control panel Program selector Adjustable outlet Door grill and lint filter Model number Power supply cord and Serial number Back plate Air intake grill Read all instructions before using this dryer.
Attention: 1.Before operation, clean off any dust and dirt inside the drum of the dryer with a damp towel. 2.Clean off any debris on the lint filter and in the duct to increase the drying efficiency. Turning on power Before turning on the power of the dryer check whether the supply voltage is in accordance with the value indicated on the name plate.
OPERATING INSTRUCTIONS 1. Power up Insert the power plug into an appropriate power outlet that is properly installed and grounded. Operating power supply: 220-240V~50Hz. 2. Laundry loading Open the door and load the laundry into the drum of the dryer. For a more energy efficient and better drying result, make sure the load has been spun dried.
20 min 60 min HDY-M60 30 min 60 min 100 min Start Cool 200 min Warm 150 min It is not recommended to turn the timer indicator to the grey area of the program cycle. 20 min 60 min 30 min 60 min 100 min Cool...
WARNING! Unplug the power cord prior to any cleaning Cleaning the surface Wipe off any dust or dirt. NOTE: Do not use excessive water,a damp cloth is fine. Do not use solvent. Do not use spray cleaners when cleaning the interior. Do not use harsh or abrasive cleaners.
UNPACKING YOUR DRYER Dimensions a(mm) b(mm) c(mm) weight(kg) HDY-M60 HDY-M40 Remove the transport packaging (fig.1) and remove the dryer rack from the top packaging (fig.2). Remove the tape on the front (fig.3 and fig.4), the wall mounting kit attached to the drum with tape on the inside and the panel film, before starting the dryer.
WALL MOUNTING INSTRUCTIONS The dryer can be mounted on the wall in the inverted position only by following these instructions. Invert the dryer so that the control panel is at the bottom (see figure 3) this allows easier access to the controls. 1.
WALL MOUNTING INSTRUCTIONS 3. Install the hooks to the dryer, in the inverted position, remove the 2 screws and 2 plastic plugs as indicated in Fig.1 . plastic plugs 4. Align the hooks as shown in Fig.2 and refit screws tightly. Install the spacers provided as Fig.2.
WALL MOUNTING INSTRUCTIONS 5. With assistance, mount dryer on wall brackets. See Fig. 3 6. A second control panel with inverted symbols is supplied. Peel the release paper from the back of inverted film then place new control panel film on the surface so that the writing is the correct way around.
DRYING RACK FITTING INSTRUCTION DRYER FREE STANDING-UPRIGHT For ease of access, the rack is to be mounted near the dryer top. Firstly hold the rack horizontally with the two end projections pointing upwards and away from yourself. Position the rack near the top of the dryer and place the end of the right rack projection into the right cabinet mounting hole (Fig.1).
RACK FITTING INSTRUCTION RACK STORAGE - DRYER INVERTED. To hold the dryer rack out of the way when not in use, it will be necessary to attach the retaining clip to the base of your dryer. To do this, firstly remove the screw located 4 cm from the right corner of the inverted dryer ( Fig.3).
The following must be confirmed before calling for service: Problem Possible Cause -Is the dryer plugged in? -Is the power on? -Is the door closed properly? The dryer does not start -Has a drying program been set? -Has the Start button been pressed? -Was the correct drying program set? -Is the filter screen clean? The drying result is not...