Summary of Contents for Viking DCWH Classic Chimney
Page 1
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com Designer Hoods F20472D EN (022410)
All Viking ventilator kits are or ceilings, or into attics, crawl spaces, or Exterior Ventilator Dimensions _____________________________________________________________________27 designed specifically for use with Viking hoods. Use of any garages. DBCV Wall Custom Ventilator System non-Viking ventilator kit will void the hood warranty.
Dimensions & Specifications IMPORTANT– Please Read and Follow! (DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator) W A R N I N G ” ( 4 0 TO REDUCE THE RISK OF INJURY TO PERSONS ” ( 3 0 IN THE EVENT OF A RANGETOP GREASE FIRE, OBSERVE THE FOLLOWING.
Dimensions & Specifications Installing Hood Canopy (DPPV Custom Power Packs w/Standard Ventilator System) (Custom Hood Canopy Cutouts C C u u s s t t o o m m H H o o o o d d C C a a n n o o p p y y *For best results, M M a a k k e e s s u u r r e e t t h h e e b b a a c c k k w w a a l l l l center the unit over...
Clearance Dimensions Interior Ventilator Dimensions (DPPV Custom Power Packs w/Standard Ventilator System) (DPPV Custom Power Packs w/Standard Ventilator System) Top view ( C u s t o 16” (40.6 cm) 4” 30”W. 14-15/16” (37.9 cm) (10.2 cm) ” m ( 1 6 ”...
Dimensions & Specifications Installing Hood Canopy (Custom Hood Canopy Cutouts (DBCV Wall Custom Ventilator System) C C u u s s t t o o m m H H o o o o d d *For best results, M M a a k k e e s s u u r r e e t t h h e e b b a a c c k k w w a a l l l l C C a a n n o o p p y y o o f f t t h h e e c c u u s s t t o o m m h h o o o o d d center the unit over...
Dimensions & Specifications Built-In Wall Custom Ventilator System Dimensions (DICV Island Custom Ventilator Systems 36”, 42”, & 54”) (48”W. DBCV Models 11” (27.9 cm) 10” (25.4 cm) 1” (2.5 cm) *For best results, M M a a k k e e s s u u r r e e t t h h e e b b a a c c k k w w a a l l l l center the unit over o o f f t t h h e e c c u u s s t t o o m m h h o o o o d d 11-3/4”...
Clearance Dimensions Installing Hood Canopy (DICV Island Custom Ventilator System) (Custom Hood Canopy Cutouts C C u u s s t t o o m m H H o o o o d d ( C u s t o C C a a n n o o p p y y ”...
Installation (DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator and DPPV Custom Power Packs w/Standard Ventilator) Planning Information Plan where the duct work will be located. Install 300 or 600 CFM proper-sized duct work, roof, or wall cap for the Roof cap single blower interior-power...
Slide filter front over front lip. Push filter rear up, then CAUTION: If not using a duct cover, using screws CAUTION: Secure vent hood to wall using screws slide back over rear lip. provided. Use additional mounting screws and wall provided make sure top mounting screws are secured anchors, if necessary.
Installation (DCH 12”H. Classic Chimney Wall Hoods w/Recirculating Kit) Remove damper and discard with transition. Turn recirculating unit upside down. Place vent hood Flip hood over. Insert 6” of electrical wiring through the CAUTION: Secure vent hood. Make sure mounting upside down on recirculating unit.
To install ventillation kit refer to ventillation kit installation instructions. Slide spacer front over front lip. Push spacer rear up, Slide filter front over front lip. Push filter rear up, then Slide filter front over front lip. Push filter rear up, then then slide back over rear lip.
Place duct cover top inside duct cover base and lower until Slide duct cover in place and fasten from inside canopy Insert 6” of electrical wiring through the top of vent hood CAUTION: Using screws provided, secure vent hood to wall. desired height is found.
Slide filter front over front lip. Push filter rear up, then Slide spacer front over front lip. Push spacer rear up, Place duct cover top inside duct cover base and lower until Slide duct cover in place and fasten from inside canopy slide back over rear lip.
Installation (DCIH Classic Chimney Island Hoods) Run duct work down to bottom edge of duct Attach canopy to duct cover/soffit. From inside of Check framing where cutout will be. Cut appropriate size hole in ceiling. Either 7” or 10” cover/soffit and secure in place. Make sure the duct hood, seal top of hood to duct with aluminum tape.
Service & Registration Service & Parts Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.