Panasonic AJ-PX270 Operating Instructions Manual page 123

Item
[Yl-R (SAT)]
[Yl-R (PHASE)]
[Yl-R-R (SAT)]
[Yl-R-R (PHASE)]
[MASTER PED]
[RGB BLACK CONTROL [R PED]
SETTING]
[G PED]
[B PED]
[PEDESTAL OFFSET]
[GAMMA MODE SEL]
[GAMMA SETTING] [MASTER GAMMA]
[F-REC DYNAMIC LVL]
[F-REC BLACK STR
LVL]
[V-REC KNEE SLOPE]
[V-REC KNEE POINT]
[BLACK GAMMA]
[B. GAMMA RANGE]
[KNEE SETTING] [KNEE MODE]
[A.KNEE RESPONSE]
[KNEE MASTER POINT] Sets the knee point position in 0.5% steps.
Chapter 6 Menu Operations — Menu list
Corrects the color saturation between yellow and red.
[−63]...[63]
f Factory setting: [0]
Corrects the hue between yellow and red.
[−63]...[63]
f Factory setting: [0]
Corrects the color saturation between "colors between yellow and red" and red.
[−63]...[63]
f Factory setting: [0]
Corrects the hue between "colors between yellow and red" and red.
[−63]...[63]
f Factory setting: [0]
Sets the master pedestal.
[−200]...[200]
f Factory setting: [16]
Sets the Rch pedestal level.
[−100]...[100]
f Factory setting: [0]
Sets the Gch pedestal level.
[−100]...[100]
f Factory setting: [0]
Sets the Bch pedestal level.
[−100]...[100]
f Factory setting: [0]
Sets the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.
[ON]: Keeps each of the values set in [R PED], [G PED], and [B PED].
[OFF]: Sets the pedestal level of Rch, Gch, and Bch to [0].
f Factory setting: [OFF]
Selects the gamma curve.
[HD]: The video gamma feature for HD (High Definition).
[SD]: Increases gain in darker areas more than HD gamma.
[FILMLIKE1]: Feature that reproduces more highlight areas compared to HD gamma.
[FILMLIKE2]: Feature that reproduces more highlight areas compared to [FILMLIKE1].
[FILMLIKE3]: Feature that reproduces more highlight areas compared to [FILMLIKE2].
[FILM-REC]: The cine gamma feature for film.
[VIDEO-REC]: The cine gamma feature for video.
f Factory setting: [HD]
Sets the master gamma in 0.01 steps.
[0.30]...[0.75]
f Factory setting: [0.45]
When [FILM-REC] is selected in [GAMMA MODE SEL], dynamic range is set. If an item other than
[FILM-REC] is selected, no settings are changed.
[200%], [300%], [400%], [500%], [600%]
f Factory setting: [600%]
When [FILM-REC] is selected in [GAMMA MODE SEL], black stretch is set. If an item other than
[FILM-REC] is selected, no settings are changed.
[0%]...[30%]
f Factory setting: [0%]
When [VIDEO-REC] is selected in [GAMMA MODE SEL], knee slope is set. If an item other than
[VIDEO-REC] is selected, no settings are changed.
[150%], [200%]...[500%]
f Factory setting: [500%]
When [VIDEO-REC] is selected in [GAMMA MODE SEL], knee point is set. If an item other than
[VIDEO-REC] is selected, no settings are changed.
[30%]...[107%]
f Factory setting: [30%]
Sets the gamma curves of dark areas.
[−8]...[−1]: Compresses the dark areas.
[OFF]: Standard state
[1]...[8]: Expands the dark areas.
f Factory setting: [OFF]
Sets the maximum level of compression/expansion.
[1]: About 20%
[2]: About 30%
[3]: About 40%
f Factory setting: [1]
Sets the knee operation mode.
[AUTO], [MANUAL], [OFF]
f Factory setting: [AUTO]
Sets the auto knee response speed. The smaller the setting value, the faster the response speed is.
[1]...[8]
f Factory setting: [4]
[70.0%]...[107.0%]
f Factory setting: [93.0%]
– 123 –
Description of settings