Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections - Kenmore 665.1628 Use & Care Manual

Quick Rinse (on some models)
Use this rinse cycle for rinsing dishes, glasses, and silverware
that will not be washed right away.
Do not use detergent with this cycle.
Wash Main Rinse Final Dry Time Water
Wash or Heated (rain) Usage
Purge Rinse (gal/L)
• 10 1.8-2.2/
Rinse 6.8-8.3
*If the incoming water temperature is less than the
recommended temperature or food soils are heavy, the cycle will
automatically compensate by adding time, heat and water as
needed.
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to access the
control panel.
2. Press CANCEL. The Cancel light glows.
3. Close the door. The dishwasher starts a 2-minute drain (if
needed). Let the dishwasher drain completely. The light turns
off after 2 minutes.
To stop the drain
You can press CANCEL again to stop the drain. Remember to
drain the dishwasher before starting a new cycle.
To clear the indicators
Press CANCEL before starting the dishwasher to clear all options
and cycles.
During the first minute of a cycle
1. Open the door. The Start light begins flashing.
2. Press a new cycle and/or options.
3. Check the detergent dispensers. They must be filled properly
for the new cycle.
4. Press START and firmly close the door (on top control
models). Or, firmly close the door and press START (on split
control models).
After the first minute of a cycle
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to access the
control panel.
2. Press CANCEL. The Cancel light glows.
3. Close the door. Your dishwasher starts a 2-minute drain (if
needed). Let the dishwasher drain completely. The light turns
off after 2 minutes.
NOTE: If your dishwasher does not need draining, the light
turns off.
4. Open the door. Select a new cycle and/or options.
5. Check the detergent dispensers. They must be filled properly
for the new cycle.
6. Press START and firmly close the door (on top control
models). Or, firmly close the door and press START (on split
control models).
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door. The Start
light begins flashing.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Press START and firmly close the door (on top control
models). Or, firmly close the door and press START (on split
control models).
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START to use the same cycle and option(s) as the previous
wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
TURBOZONE
TM
wash option
Select this option to activate the TURBOZONE
TM
jets and provide
intensified water spray to the back of the lower dishrack. The
TURBOZONE
TM
wash option provides a concentrated wash action
to pots, pans, casseroles, etc. with tough baked-on foods.
This option may add heat and wash time to the cycle.
NOTE: TURBOZONE
TM
is an option with the SMART WASH
TM,
Pots Pans, and Normal Wash cycles.
IMPORTANT: Load pots, pans, casserole dishes, etc. facing the
TURBOZONE
TM
jets in the back of the lower dishrack. Tip items
toward the rear of the dishrack to maximize coverage. Only one
row of items may face the TURBOZONE
TM
jets. Stacking,
overlapping, or nesting items will prevent the TURBOZONE
TM
jets
from reaching all of the surfaces.
Side view of TURBOZONE
TM
wash area
15