Advertisement
The properties include:
• Display Brightness—Set the light level (brightness) of the screen backlight.
Choose a percentage from 0 (Off) to 100 (full brightness).
• Keypad Brightness—Set the light level (brightness) of the keypad backlight.
Choose a percentage from 0 (Off) to 100 (full brightness).
• Sleep Mode—Set how long the System Remote Control stays awake after
no activityThe default setting is 15 seconds, but can be extended up to 60
seconds or can be reduced down to 0 to conserve battery life.
• Battery Level—Displays the current strength of the batteries.
• Channel—Displays the ZigBee channel set for the SR-250, which should
match the ZigBee channel for the Controller.
• Gateway—Displays the MAC address of the Zigbee Server (usually your
Controller unless you specify differently).
• MAC—Displays the System Remote Control's own MAC address.
• Firmware Version—Displays the current firmware version.
7
Check or change the ZigBee Channel: If you need to change the ZigBee
channel to match the Controller's channel (which is sometimes changed to
improve reception), do the following at the SR-250:
• Press the List button, and then select Info > Config.
• Press buttons 2, 4, 8, 6, #, *, List (in that order) to get into Edit mode.
• On-menu List, Info, and Config:
-Display Brightness
-Keypad Brightness
-Motion Detect
-Battery Level
-Factory Default
-About
• Press the up or down arrows to change the ZigBee channel.
• Press List to exit Edit mode and save the changes.
Program the Programmable Buttons
On the System Remote Control SR-250, you can program six (6) soft buttons (Red,
Green, Yellow, Blue, *, and #) to perform programmed activities.
These buttons can be programmed to execute any of the AV device's macros or IR
codes. Program these options using the AV device properties page.
1
Start Composer and connect to a Director.
2
Ensure the System Design view is selected.
3
Ensure that you have the following devices in your project:
• Controller
• System Remote Control SR-250
• An AV device to be controlled
4
Select the Connections view.
5
On the Network tab, ensure the Controller and the System Remote Control
are both network identified (have a network address).
6
Program the programmable buttons (Red, Green, Yellow, Blue, *, or #) either
based on the selected AV device or the selected room.
Based on AV Device (Pictured):
•
Select the System Design view.
•
Select an AV device to display the device's Properties page.
•
On the device's Properties page, choose Code or Macro for the button you
want to program, and then choose a code or macro from the drop-down list,
edit the Help text as needed, and then choose Set.
Note:
Help text describes custom programming to end-users under the
House option in any of the Navigators.
For example:
(1) In System Design view, select Disc Changer.
(2) Under Red button, choose Code.
(3) From the drop-down list, choose Subtitle.
(4) Choose the Set button to create a Subtitle button.
Based on Room:
•
Select the Programming view.
•
Select a room in the Device Events pane.
•
Select the Commands radio button in the [Room] Events pane.
•
Use the drop-down menu to select a command or button (such as "Blue
Button").
•
Build the script using items from the Actions pane to program the actions
desired in the selected room when you select the command or button.
•
For more information about programming, see the Composer Pro User Guide.
Program System Remote Control Paging
You can configure the Beep paging feature of the SR-250 through programming.
This feature can be used to page a lost System Remote Control. A keypad or
custom button can be programmed to cause the System Remote Control to beep
when pressed. This lets the user find the lost System Remote Control.
To program the paging feature for this System Remote Control:
1
Start Composer and connect to a Director.
2
Select the Programming view.
3
Select the Event that you want to use to start the page. For example, to
select a keypad button press, first select the keypad under the Device Event
section (on the left), and then select the button under Events.
4
In the Actions list (on the right), select System Remote Control SR-250.
5
In the Commands list, choose an action for the System Remote Control, and
then double-click the green arrow to add the action to the Script pane.
Advertisement
