About The Signals To Input To Genlock In Connector; About The Ret Signal - Panasonic AG-BS300E Operating Instructions Manual

About the Signals to Input to GENLOCK IN Connector

Supply the following signals to the GENLOCK IN connector, as a GENLOCK input signal to this unit, in accordance with the
video format used.
Video may be disrupted if any other signals are supplied.
Video format of the camera recorder
1080/59.94i
1080/23.98PsF
1080/50i
1080/24PsF
720/59.94P
720/60P
720/50P
480/59.94i
576/50i
<Note>
When using the unit in HD mode, input the HD 3-value SYNC signal or black burst signal. When using the SD mode, input the
black burst signal. When the SD 2-value SYNC signal without a burst signal is supplied, GENLOCK does not work.

About the RET Signal

The RET signal input to this unit can be transferred to the camera adapter.
When the video format of the camera recorder is HD format, the video signal supplied to the RET IN SDI connector and the
RET IN VIDEO connector can be transferred to the camera adapter. When the video format of the camera recorder is SD
format, either of the video signals supplied to the RET IN SDI connector or the RET IN VIDEO connector can be transferred to
the camera adapter.
The signal output to the VF OUT connector (D-Sub connector) of the camera adapter can be switched with the RET signal
selection switch at the rear panel of this unit.
Video format of the
Input signal
camera recorder
connector name
RET IN SDI
RET IN VIDEO
RET IN SDI
RET IN VIDEO
HD
RET IN SDI
RET IN VIDEO
RET IN SDI
RET IN VIDEO
RET IN SDI
RET IN VIDEO
RET IN SDI
RET IN VIDEO
SD
RET IN SDI
RET IN VIDEO
RET IN SDI
RET IN VIDEO
*1 When the video format of the camera recorder is HD format, SD SDI signals cannot be transmitted.
*2 When the video format of the camera recorder is SD format, HD SDI signals cannot be transmitted.
16
Signal to be supplied to the GENLOCK IN connector (analog signal)
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
When HD SYNC is supplied
When SD SYNC is supplied
Input signal of the AG-BS300P/E
Input signal
HD SDl (signal A)
Composite (signal B)
HD SDl (signal A)
Composite (signal B)
1
SD SDl (signal C)*
Composite (signal B)
1
SD SDl (signal C)*
Composite (signal B)
SD SDl (signal A)
Composite (signal B)
SD SDl (signal A)
Composite (signal B)
2
HD SDl (signal C)*
Composite (signal B)
2
HD SDl (signal C)*
Composite (signal B)
1080/59.94i, 3-value SYNC
480/59.94i, black burst signal (SYNC + burst)
1080/23.98PsF, 3-value SYNC
Not supported
1080/50i, 3-value SYNC
576/50i, black burst signal (SYNC + burst)
1080/24PsF, 3-value SYNC
Not supported
720/59.94P, 3-value SYNC
480/59.94i, black burst signal (SYNC + burst)
720/60P, 3-value SYNC
Not supported
720/50P, 3-value SYNC
576/50i, black burst signal (SYNC + burst)
Not supported
480/59.94i, black burst signal (SYNC + burst)
Not supported
576/50i, black burst signal (SYNC + burst)
Output signal to the AG-CA300G
RET signal selection VF OUT connector
switch at the rear
HD component
SDI
(signal A)
SD component
VIDEO
(signal B)
SDI Signal is not output
SD component
VIDEO
(signal B)
SD component
SDI
(signal A)
SD component
VIDEO
(signal B)
SDI Signal is not output
SD component
VIDEO
(signal B)
RET OUT connector
(D-Sub) (BNC)
Composite (signal B)
Composite (signal A)
Composite (signal B)