Table of Contents
Advertisement
Menu Number
/ Short Name
Carrier Squelch
Mutes the speaker of the transceiver in the absence of a strong signal. VHF squelch is
0
either OFF or ON. UHF squelch is either OFF or one of 9 levels. The higher the level, the
stronger the signal must be to un-mute the speaker.
SQL
Settings: 0 - 9
Note: The CALL button (FM or ALARM) is not functional when menu 0 = 0
Frequency Step (KHz)
Selects the amount of frequency change in VFO/Frequency mode when scanning or
1
pressing the [▲] or [▼] keys.
STEP
Settings:
Transmit Power
Selects between HIGH and LOW transmitter power when in VFO/Frequency mode. Use
the minimum transmitter power necessary to carry out the desired communications.
Settings: HIGH[0] | LOW[1]
2
HIGH: ≈ 5 watts
TXP
LOW: ≈ 1 watt
Note: When TXP is set to LOW, an 'L' is indicated in the status display
Note:
Battery Save
Selects the ratio of sleep cycles to awake cycles (1:1, 2:1, 3:1, 4:1). The higher the
3
number the longer the battery lasts. When enabled, a word or two might be missed when
SAVE
the frequency being monitored becomes active.
Settings: OFF[0] | 1 | 2 | 3 | 4
Voice Operated Transmission
When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the
4
gain level to an appropriate sensitivity to allow smooth transmission.
VOX
Settings: OFF[0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10
Note: When VOX is not set to OFF, 'VOX' is indicated in the status display
Wideband / Narrowband
Wideband (25 kHz bandwidth) or narrowband (12.5 kHz bandwidth).
5
Settings: WIDE[0] | NARR[1]
WN
Emission: 16K0F3E / 11K0F3E (W/N)
Deviation: ≤ ±5 kHz / ≤ ±2.5 kHz (W/N)
Note: When WN is set to NAR, an 'N' is indicated in the status display
Backlight Timeout (seconds)
6
Settings: OFF[0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10
ABR
Note:
Note: ABR can be set to 24 using CHIRP
Dual Watch / Dual Reception
Monitor [A] and [B] at the same time. The display with the most recent activity ([A] or [B])
becomes the selected display.
7
Settings: OFF[0] | ON[1]
TDR
Note: When TDR is set to ON, an 'S' is indicated in the status display
Note: The selected display can be forced back to [A] or [B] using menu 34
Note: TDR should be set to OFF when manually programming
Note: TDR is inhibited while scanning is in operation
Reference for UV-82 Menus
by Jim Unroe - KC9HI
(send comments, suggestions or corrections to UV-82@KC9HI.net)
Long Name / Description / Settings / Notes
2.5K[0] | 5.0K[1] | 6.25K[2] | 10.0K[3] | 12.5K[4] |
20.0K[5] | 25.0K[6] | 50.0K[7]
The power level can be toggled in MR/Channel mode by tapping the
[#╓O] key
The ABR setting also sets the delay before the radio returns to FM
broadcast reception after being interrupted
11-January-2014
Default: 5
Default: 2.5K
Default: HIGH
Default: 3
Default: OFF
Default: WIDE
Default: 5
Default: ON
Separate
MR/
VFO/
Channel
Frequency
Global
Mode
Mode
✓
✓
RO
✓
✓
✓
RO
✓
✓
✓
Stored
VFO
on a Per
A & B
Channel
Settings
Basis
✓
✓
✓
✓
✓
Hide quick links:
Advertisement
Table of Contents
