Table of Contents
Advertisement
RF Power Output
Value is in percent, from 0% to 100%. Use and RF wattmeter
ATPO
to confirm the power setting, and adjust the % accordingly to
obtain the desired RF power level.
Read TX Current
ATPC
last transmission, in mA.
Over-The-Air bit rate - This is the data rate the radio uses
to send data over the air. All RF modems in the network
ATR2
must use the same over-the-air baud rate. Refer to
section 9 for information on how to set the OTA baud rate.
Receiver Signal Level – Reads the Receiver Signal
ATRQ
strength this instant, and returns the level in dBm.
RSSI (Receive Signal Strength Indicator) – Returns the
signal level of last received packet. The reading is in dBm.
ATRS
Usable for relative comparison of signals, but absolute value
is within10dB at -90dBm.
Disable Remote Access – When enabled (set to a 0), the
ATRV
modem will respond to over-the-air RPR requests, Pings, and
over-the-air commands. Default is OFF (1).
Serial Number – Reads and returns a unique serial number
ATSL
for thjs unit.
Show – Display the configuration of the modem. This will
ATSH
return a page of ASCII characters, showing the main
configuration parameters.
Power Savings Options – When set to 0, the internal radio
receiver will be ON. When set to 4 (default for the ATLAS
ATSM
PL), the internal radio receiver will always be OFF and the
radio will not receive over-the-air messages.
Statistics – Show the unit's operational statistics. See
ATST
Statistics section of user manual.
Read product temperature – Read the internal temperature
ATTE
of the unit's circuit board in degrees Celsius.
Max Packet Size – Set the maximum number of bytes in an
ATTT
over-the-air packet.
Read DC input Voltage– Returns the DC input voltage
ATVB
reading, in mV (12500 = 12.5VDC input).
Firmware Version – Returns firmware version currently
ATVR
loaded on the module.
Show or Configure the Repeat Table – Set the addresses
ATXn
that this unit will store-and-forward data to/from. n = 1, 2, 3, or
4 designating the entry in the table to show or edit..
Enable/Disable Store and Forward Repeating – 0=disabled,
ATXR
1 – enabled.
Enable/Disable single-hop repeating – 0=any number of
ATHX
repeats, 1 – unit will not repeat a packet that was already
repeated.
Restore Factory – Restore the factory default values. This
AT&F
command will not erase the calibration values.
Ping another modem. Format is PING xxxx, where xxxx is
PING
the ID of the modem to ping. If remote access is enabled on
xxxx, it will respond.
Company Confidential
. Set or show the RF power output setting.
. Read the device's current draw during the
20
0-110
0-9999
Range:
0 = 800
5 = 9600 2L
1 = 1200
6 = 19200 4L
2 = 2400
7 = 5142 2L
3 = 4800
8 = 9600 4L
4 = 8000 4L 9 = 2000 2L
10=14.4k 4L
Range: -40 to –130 (dBm)
No parameters. Returns a
number : -50 to –140
(dBm) varies by model.
0= Remote Access on
1=Remote Access off
Read Only
1 - 999999999
none
Range: 0, 1, 2
0, 1,2, 3, 4, or 5
-40 to +99
1 - 512
None
Read Only, 3
characters
Four parameters
aaaa bbbb cccc dddd where
aaaa=Source Address
bbbb = S.A. Mask
cccc = Destination Address
dddd = D.A. Mask
0 or 1
0 or 1
0 (multi-hop OK)
XXXX
Raveon Technologies Corp.
100
-
3
-
none
1
unique
None
4
(RX OFF)
None
-
80
none
none
0 (Off)
none
-
Advertisement
Table of Contents
