1. Manuals
  2. Brands
  3. Excalibur Water Systems Manuals
  4. Water Filtration Systems
  5. EWR 5075
  6. Installation, operation & service manual

Excalibur Water Systems EWR 5075 Installation, Operation & Service Manual

Reverse osmosis drinking water systems
Hide thumbs
Table of Contents

Advertisement

Quick Links

REVERSE OSMOSIS DRINKING WATER SYSTEMS
 
 
 
 
Model: EWR 5075
INSTALLATION, OPERATION &
SERVICE MANUAL
Barrie, Ontario Canada
www.excaliburwater.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EWR 5075 and is the answer not in the manual?

Questions and answers

Related Manuals for Excalibur Water Systems EWR 5075

Summary of Contents for Excalibur Water Systems EWR 5075

  • Page 1 REVERSE OSMOSIS DRINKING WATER SYSTEMS         Model: EWR 5075 INSTALLATION, OPERATION & SERVICE MANUAL Barrie, Ontario Canada www.excaliburwater.com...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page INTRODUCTION TO THE REVERSE OSMOSIS DRINKING WATER SYSTEM PREPARATION A. Major System Components for the Reverse Osmosis Drinking Water System Installation Drawings for the Reverse Osmosis Drinking Water Systems B. Tools Recommended for Reverse Osmosis Drinking Water Installation C.
  • Page 3 INTRODUCTION The Reverse Osmosis membrane is a specially Your new Reverse Osmosis Drinking Water constructed, fully aromatic polyamide film, and is System uses a combination of filtration classified as a Thin Film Composite (T.F.C.). technologies to reduce unwanted contaminants in The spiral wound construction of the Reverse your water supply.

  • Page 4: Water System

    REVERSE OSMOSIS PREPARATION A. Reverse Osmosis Components The following components comprise the Reverse 9. Reverse Osmosis Sediment Pre-filter, Osmosis Drinking Water System. (Refer to Fig. 1, shrink wrapped. below for general system layout.) 10.Reverse Osmosis activated Carbon Pre- filter, shrink wrapped. 1.
  • Page 5 BALL...

  • Page 6: Tools Recommended For Reverse Osmosis Drinking

    B. Tools Recommended for Reverse Osmosis C. Site Selection for Major System Reverse Installation Osmosis Components The following tools will cover most of the The Reverse Osmosis System was designed to fit Reverse Osmosis installation sites under a sink, however, because of space limitations encountered: or other reasons, the Reverse Osmosis system's flexible design allows for other locations.

  • Page 7: Reverse Osmosis Installation Steps

    4. Reverse Osmosis Feed Water 2b. Drilling a porcelain sink: Connection – The Reverse Osmosis Feed It is best to use a special 5/8" diameter cutter Water Saddle Valve should be located as designed for porcelain. A carbide tipped close to the manifold assembly as masonry bit is a second choice.

  • Page 8: Reverse Osmosis Feed Water Ball Valve Installation

    B. Reverse Osmosis Feed Water Ball Valve Installation 3. With the Reverse Osmosis Feed Water Ball Valve closed, open the Reverse Osmosis Decide on location. Do NOT connect sink faucet and the water supply and allow Reverse Osmosis to a hot water feed line. the water to run for a few minutes to flush Water over 100ºF may cause permanent any debris caused by the installation.

  • Page 9: Reverse Osmosis Drain Clamp Installation

    C. Reverse Osmosis Drain Clamp Installation 3. Locate the 3/8" Drain Tubing connected to the Reverse Osmosis System. Route to the Choose the Reverse Osmosis drain outlet Reverse Osmosis tubing to the Drain Clamp location. and trim to length. The following are instructions for discharging CAUTION: The lowest point of the line in the sink drain pipe.

  • Page 10: Reverse Osmosis Start Up

     Slowly open the Reverse Osmosis Feed D. Position the Reverse Osmosis Holding Tank & Make the Final Hose Connections Water Saddle Valve (turning counter clockwise). 1. Check the Reverse Osmosis tank pre-  As soon as the water begins to come out of charge pressure.

  • Page 11: Reverse Osmosis Operation And Maintenance

    REVERSE OSMOSIS OPERATION & 1. Close the Reverse Osmosis Feed Water Ball MAINTENANCE Valve by turning fully clockwise and open the Reverse Osmosis Dispensing Faucet by A. Reverse Osmosis Normal Operation lifting the handle. Allow the Reverse 1. Reverse Osmosis systems produce Osmosis Holding Tank to empty.

  • Page 12: Post Filter

    3 ml) into the Reverse Osmosis tubing and 5. Slowly open the Reverse Osmosis Feed reconnect it to the Tee. Water Saddle Valve. NOTE: Now is the convenient time to 6. When water begins dripping out of the change the In-Line Reverse Osmosis Reverse Osmosis Faucet, in the Activated Carbon Post Filter.

  • Page 13: Reverse Osmosis Troubleshooting Guide

    REVERSE OSMOSIS TROUBLE SHOOTING GUIDE Problem Possible Cause Solution Low quantity of Reverse Reverse Osmosis Feed Water Ball Open Valve or unclog. Osmosis Product Water from Valve is plugged or closed. Holding Tank Clogged Sediment Pre-filter or Replace Reverse Osmosis filters. Activated Carbon Pre-filter.
  • Page 14 Problem Possible Cause Solution High Total Dissolved Solids The Product Water and Drain Correct plumbing. (TDS) in the Product Water Water lines are reversed. (continued) No drain flow, Reverse Osmosis Clear or replace Reverse Osmosis Drain Restrictor is clogged. Drain Restrictor. The Reverse Osmosis ASO Valve Repair or replace the Reverse is not closing.
  • Page 15 Warranty ~ Working Procedures If during the suitable warranty period, a part is defective, then Excalibur Water Systems will repair or replace that part at no charge to the original owner, with the exception of charges for nominal shipping, service and/or installation.

Table of Contents