Olivetti AR-FN6 Service Manua
  1. Manuals
  2. Brands
  3. Olivetti Manuals
  4. Printer Accessories
  5. AR-FN6
  6. Service manua
Olivetti AR-FN6 Service Manua

Olivetti AR-FN6 Service Manua

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Options
AR-FN6
SERVICE MANUAL
Code
Y105620-2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AR-FN6 and is the answer not in the manual?

Questions and answers

Related Manuals for Olivetti AR-FN6

Summary of Contents for Olivetti AR-FN6

  • Page 1 Options AR-FN6 SERVICE MANUAL Code Y105620-2...
  • Page 2 PUBLICATION ISSUED BY: Olivetti S.p.A. 77, Via Jervis - 10015 Ivrea (TO) Italy Copyright © 2006, Olivetti All rights reserved...

  • Page 3: Table Of Contents

    AR-FN6 CONTENTS PRODUCT OUTLINE ....... . 1 - 1 CONFIGURATION........2 - 1 SPECIFICATIONS .

  • Page 4: Product Outline

    2. This unit cannot be installed together with the male bin stacker (AR-MS1) and the upper exit tray extension (AR-TE4). Exit tray B/W scanner module/DSPF (AR-EF3) (AR-TE3 or AR-DU4 Standard) Duplex module/bypass tray (AR-DU4) Upper exit tray extension (AR-TE4) Finisher (AR-FN6) Duplex module (AR-DU3) Simultaneous installation not allowed Simultaneous installation not allowed Saddle stitch finisher Mail-bin stacker...

  • Page 5: Specifications

    Index paper:176g/m² / 47lbs Name Content Life Remark name Cover paper:205g/m² / 54-55lbs Transparency Staple Staple x3 3000x3 AR-SC1 Common with cartridge cartridge cartridge for AR-FN4 & AR-FN6 Lower Plain 60-128g/m² /16-34lbs Tray Remaining Upper Not provided paper tray detection Lower Provided Tray...

  • Page 6: Unpacking And Installation

    • Start installation after checking that the DATA and COMMUNICATION indicators on the operation panel are neither lit nor blinking. • For installation of AR-FN6, an optional stand/paper drawer (stand/MPD & 2000 sheet paper drawer, stand/3 x 500 sheet paper drawer or multi purpose drawer) must have been installed.
  • Page 7 <4>Open the front cover of the finisher and fix the finisher with three <3>Insert the staple cartridge. screws A at the positions shown in the illustration. Then, close the front cover and close the paper tray of the stand/ paper drawer. (Front side) <4>Slide the release lever to the left and return the staple unit.
  • Page 8 7) Attach the power supply unit. 9) Remove the AC inlet cover and then remove the rear cabinet of the Attach the power supply unit to the hanging portions and secure it stand/paper drawer. using the supplied three screws. <1>Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.
  • Page 9 11) Attach the rear cabinet of the stand/paper drawer. 12) Connect the AC cord of the optional power supply unit to the main <1>Pass the AC cord of the power supply unit as shown in the illustration unit of the printer. and fix the rear cabinet of the stand/paper drawer with the screws.

  • Page 10: External Views And Internal Structures

    [5] EXTERNAL VIEWS AND INTERNAL STRUCTURES A. External view " Top cover SF Knob Top tray Staple cartridge Offset tray Front door Staple unit B. Internal structure " & Finisher transport roller R1 De-curler roller Transport roller R2 No.1 tray paper exit roller S paper entry roller Transport roller R2 Stapler unit...
  • Page 11 C.Sensor 5.SCID 1.PID 6.SCID2 10.PSHP 2.DOPD 13.STUHP 8.JFHP 4.PPD 12.STTHP2 11.STTHP1 19.DSW2 3.T1PF 20.STHP 9.JRHP 18.DSW1 7.SCPD 15.T2UP 21.STNC 22.STLS 23.STSP 17.T2PD 14.POD 16.T2DN Code Name Function Active condition Remark Paper In Detect Sensor Detection of paper entry into the L : Paper loaded interface transport section DOPD...
  • Page 12 D. Motor, Clutch, Solenoid, PWB 12.SCGS 5.PSM 3.JFM 15.SPS 14.PPS 11.FGS 4.JRM 2.MM 6.STM 1.Main PWB 7.STUM 10.T2OM 8.STTM 9.EVM 16.T2S 13.SCRS Code Name Function Remark Main PWB Main Control PWB Communication with the machine, control of the machine operations Main Motor Drives transport rollers Jogger Front Motor...

  • Page 13: Machine Operation

    [6] MACHINE OPERATION 1. Using the stapling function from the printer feature When using the stapling function, select "Properties" on the printer driver setting screen, open the "Main" tab shown in the right illustration, and then select "Left", "Right" or "Top " at "Binding Edge" and "1 Staple" or "2 Staples" in the "Staple" drop down. NOTES: •The settings screens above will appear only if the devices have been set properly in the printer driver.
  • Page 14 3. Stapling position quick reference list When stapling is performed, the orientation of image data or original is related to the stapling position, binding position and orientation of paper complicatedly. The table below shows the relation. Image data or original Result First page (front side) Second page (reverse side) Two sides...

  • Page 15: Operational Descriptions

    [7] OPERATIONAL DESCRIPTIONS C. Paper exit to the lower tray When stapling or offset operation is performed, paper is discharged to 1. Paper transport path the lower tray. A. Machine paper exit reverse (Switchback) When the duplex print or the left side paper exit tray is selected, paper is once discharged to the interface unit and then switched back.
  • Page 16 A. Upper transport section (5) Paper holder The paper holder is driven by the paper holder solenoid (PPS) to hold the (1) Paper transport path rear edge of paper in the alignment tray. By rotating the main motor (MM), all the transport rollers in the unit (6) Alignment and paper exit in offset (except for the tray 2 final roller) are driven.
  • Page 17 (8) Staple unit (11) Paper exit after stapling The stapler staples paper. The ST shift motor slides the stapler horizontally with the paper lead edge according to the staple positions (forward, backward, 2 positions). The ST rotating motor (STTM) rotates the stapler from the save position to the stapling position, and can slide the staple replacement position horizontally and can discharge paper.

  • Page 18: Basic Operation

    (3) Paddler operation/tray 2 upper limit detection actuator operation When the paper exit motor is rotating, the tray 2 solenoid (T2S) is turned on so that the paddler is rotated to pull paper and pull the actuator toward the unit in order to improve the stacking capacity of paper loaded in the tray 2. Paper exit sensor (POD) Tray 2 upper limit...

  • Page 19: Adjustments

    [8] ADJUSTMENTS 4) When the joggers F/R stop, open the door and load A$/LT paper in the alignment tray, and check the jogger width visually. 1. Jogger position adjustment 5) When the jogger width is too wide or too narrow, use [ ] key and ] key again to change the adjustments value.

  • Page 20: Disassembly And Assembly, Maintenance

    [9] DISASSEMBLY AND ASSEMBLY, MAINTENANCE 1. Maintenance System Table Check (Clean, replace, or adjust as necessary.) Clean Replace Adjust Lubricate Move position When Unit name Part name 100K 150K 200K 250K 300K 350K 400K Remark calling Transport section Transport rollers De-curler roller Transport paper guides...
  • Page 21 2. Disassembly and assembly C.Transport unit Parts name Job item cycle A.Unit transit Transport rollers Clean 100K Note: When carrying the finisher unit removed from the printer, fold the De-curler roller Check transport unit as described below. Clean 100K If not, the frame may be bent, causing a breakdown of the Transport paper guide Clean 100K...
  • Page 22 (3) Upper open/close sensor (6) De-curler roller (4) Upper cover (7) Transport roller (5) Paper entry sensor Y105620-2 Service Manual...
  • Page 23 D. Rear side of the unit (3) Staple shift motor (4) Elevator motor / Staple rotation motor (1) Main motor (2) Main control PWB A red seal is attached to the staple rotating motor. (5) Pressure-release solenoid Y105620-2 Service Manual...
  • Page 24 E. Stapler (1) Stapler unit Parts name Job item cycle Staple UN Replace 100K staple Staple cartridge User replacement 3000pc. Y105620-2 Service Manual...
  • Page 25 F. Inside of the unit (1) Jogger motor (2) Pusher motor (3) Elevator unit Y105620-2 Service Manual...
  • Page 26 G. Right side of the unit (Paper exit side) (2) Lower stage tray paper exit roller Parts name Job item cycle Transport roller clear 100K (1) External cabinet (3) Paper exit paddler Y105620-2 Service Manual...
  • Page 27 H. Front side of the unit (3) Compiler paper entry gate solenoid Parts name Job item cycle Paper guide clean 100K I. Gears, Clutch Parts name Job item cycle Gears Lubricate 100K (1) Stopper solenoid J. Belts (2) Paper holding solenoid Parts name Job item cycle...

  • Page 28: Block Diagram, Wiring Diagram

    [10] BLOCK DIAGRAM, WIRING DIAGRAM 1. Block Diagram Y105620-2 Service Manual 10-1...
  • Page 29 2. Wiring Diagram Y105620-2 Service Manual 10-2...
  • Page 30 3. Circuit Diagram SF MAIN PWB TF UN (1/3) +24V1 1SS133 x4 +24V1 CNC-01 +24V1 CNF-02 +24V DAN202K x BR28 +24V2 10KJ x4 +24V2 10KJ x4 10KJ x4 CNF-03 10KJ x4 PPD/ PPD/ CNH-27 SCID2/ SCID2/ CNH-25 JFHP JFHP TEST CNH-02 CNE-16 JRHP...
  • Page 31 COM1 CNG-01 (PID) 220J(1/4W) D112 D111 COM2 CNH-13 DAN202K x2 (SCID) 220J(1/4W) (1-B2) SEL0 COM3 SEL1 CNH-23 (SCID2) SEL2 /SCK2 220J(1/4W) BR12 BR13 (1-B2) 10KJ x4 10KJ x4 IC105 IC108 (STTD) 24VM/ STTD CNE-15 DSW1/ SCPD/ SCPD/ CNH-11 DSW2/ MMLK MMLK CND-04 TEST...
  • Page 32 SF MAIN PWB TF UN (2/3) 0.47J(1W) 6.8KJ 332Z/50V +24V 222Z/50V IC102 47U/35V 222Z/50V 332Z/50V Rs A Vs A 6.8KJ Vs B 0.47J(1W) Rs B CR A Vref A CR B Vref B JFMA JF/A IN /A OUT A CNF-09 IN A OUT /A JFM/A...
  • Page 33 +24V2 DTC114YKA x6 RXE075 STA457C Q106 100J 1SS133 STM+ CNE-03 STM+ (1-D3) 4.7KJ(1/4W) CNE-04 4.7KJ STM- 4.7KJ(1/4W) CNE-01 103Z/50V STM- Q107 CNE-02 100J 1SS133 (1-D3) 4.7KJ 4.7KJ(1/4W) 4.7KJ(1/4W) 103Z/50V Q108 Q109 Q104 473K/50V 473K/50V Q105 2.4KJ IC103B 2.4KJ STLK 100J (1-A2) BA10393F 0.22J(1W)
  • Page 34 SF MAIN PWB TF UN (3/3) CNA (S16B-PHDSS) CNB (B6B-PH-K-R) CNF (B24B-PHDSS) SIGNAL SIGNAL SIGNAL FGS-FIN/ T2OM/B GND2 RES-FIN2 +24V +24V1 DSW2 DSR-FIN2/ T2OMB +24V2 T2OM DTR-FIN2/ UART T2OMA GND2 RXD-FIN2 +24V GND2 TXD-FIN2 T2OM/A JFMB N.C. JFM/B JFM/A GND2 JFMA CND (B6B-PH-K-S) GND2...
  • Page 35 CNH (B32B-PHDSS) SIGNAL JFHP JFHP GND2 JRHP JRHP GND2 PSHP PSHP GND2 SCPD/ SCPD GND2 COM2 GND2 SCID SCID/ SCGS/ SCGS STTHP1/ STTHP1 GND2 STTHP2/ STTHP2 GND2 COM3 GND2 SCID2 SCID2/ PPD/ GND2 +24V SPS/ +24V PPS/ CNI (S3B-PH-K-S) SIGNAL T1PF/ T1PF GND2...

  • Page 36: Others

    [11] OTHERS A. SF MAIN PWB TF UN Y105620-2 Service Manual 11-1...
  • Page 37 Y105620-2 Service Manual 11-2...
  • Page 38 CAUTION FOR BATTERY DISPOSAL (For USA,CANADA) Contains lithium-ion battery. Must be disposed of properly. Remove the battery from the product and contact federal or state environmental agencies for information on recycling and disposal options.
  • Page 39 UPDATING STATUS DATE UPDATED PAGES PAGES CODE 04/2006 EDITION Y105620-2...

Table of Contents