Playback; Basic Playback - JVC HR-V610E Instructions Manual

C
Make connections
Connect the recorder's L-2 IN/DECODER connector to the satellite
receiver's 21-pin SCART connector.
D
Connect Satellite Controller to recorder
Connect the Satellite Controller to the SAT CONTROL connector
on the rear panel.
Transmitter
Satellite Controller 21-pin SCART cable
(not provided)
(not provided)
To SAT CONTROL
E
Turn on satellite receiver
Turn on the satellite receiver's power.
F
Access Main Menu screen, then Initial Set screen
Press MENU. Press RT to place the pointer next to "INITIAL
SET", then press OK or
G
Access Sat Control Set screen
Press RT to place the pointer next to "SAT CONTROL SET", then
press OK or .
H
Enter satellite receiver's brand
Press the appropriate number keys to enter
the brand code from the following list,
then press OK.
If the code you entered is invalid, the
code field will be reset. Enter the correct
code again.
BRAND NAME CODE
JVC 73
AMSTRAD 60, 61, 62, 63, 92
ASTON 97
CANAL 81
SATELLITE
CANAL + 81
D-BOX 85
ECHOSTAR 82
(VIA DIGITAL)
FINLUX 68
FORCE 89
GALAXIS 88
GRUNDIG 64, 65, 102
HIRSCHMANN 64, 78, 99
HUMAX 88
ITT NOKIA 68
JERROLD 75
KATHREIN 70, 71, 96
LUXOR 68
MASCOM 93
I
Select satellite receiver's channel for testing
Press the appropriate number keys to enter the channel position
on the satellite receiver, then press OK. The recorder enters the
test mode.
J
Check result of the test
If the satellite receiver's channel number
has been changed to the same one as you
set in step 9 9 9 9 ...
Press RT to place the pointer next to
"CHANGED TO ...", then press OK or
to finish the Sat Control Set mode.
Satellite receiver
To VCR
connector
To L-2 IN/
DECODER
Your recorder
.
BRAND NAME CODE
MASPRO 70
NOKIA 87, 94
PACE 65, 67, 74, 86,
92, 97
PANASONIC 74, 92
PHILIPS 66, 84, 101
RADIX 78
RFT 69
SABA 97
SAGEM 83, 90
SALORA 68
SAMSUNG 83
SIEMENS 64
SKYMASTER 69, 98
TECHNISAT 66, 100
THOMSON 97
TPS 83
TRIAX 91
WISI 64
If the satellite receiver's channel number has not been changed
correctly ...
Press RT to place the pointer next to "NOT CHANGED", then
. Then perform the procedure again from step 8 8 8 8 .
press OK or
NOTE:
The Satellite Controller may not function properly with some types
of satellite receiver.

Playback

Basic Playback

Turn on the TV and select the video channel or AV mode.
A
Load a cassette
Make sure the window side is
up, the rear label side is facing
you and the arrow on the front of
the cassette is pointing towards
the recorder.
Do not apply too much pressure when inserting.
The recorder turns on, and the counter is reset, automatically.
If the cassette's record safety tab has been removed, playback
begins automatically.
B
Start playback
Press 4.
During playback
Stop playback
Press 8 on the remote
control.
Pause playback and view still picture
Press 9.
Press 4 to resume normal playback.
If there is vertical jitter, press PR R/T on the remote control or
PR+/– on the recorder to correct the picture.
Pause and Frame-by-Frame playback
Press 9 to pause, then press
Press 4 to resume normal playback.
Picture Search
Press 3 or 5. Press 3 or 5 again to perform high-
speed search.
Each time you press 3 or 5, the search speed changes
between low-speed and high-speed.
Press 4 to resume normal playback.
Variable Speed Search (including slow-motion)
Press or
Press 4 to resume normal playback.
Each time you press
changes. To decrease the speed during picture search, press the
opposite direction button repeatedly.
During still picture, press and hold
to start reverse) slow motion playback. When you release
the button, still picture resumes. During still picture, holding 9
for more than 2 seconds also starts forward slow motion
playback. If you press 9 again, still picture resumes.
During slow motion playback, some noise may appear on the
TV screen. Press PR R/T on the remote control or PR+/– on
the recorder to eliminate the noise.
— 6 —
OR Press 0 on the recorder.
or (or 9) repeatedly.
repeatedly.
or , the playback speed
to start forward (or