Recording Features; Timer Recording; Express Timer Programing - JVC HR-J692U Instructions Manual

– Recording –

Recording Features

Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Specifying recording length
— Instant Timer Recording (ITR)
During recording, press REC (
recording length you want appears on the display panel. The
record indicator ( ) on the display panel starts blinking.
Each time you press the button, recording length increases in
30-minute intervals (up to 6 hours).
The VCR shuts off after recording is finished.
To cancel an ITR, press STOP (
( ) on the VCR.
0
Watching one program while recording another
During recording...
If you connect the TV and the VCR only using the RF
connection ( pg. 5) to view pictures from the VCR, press TV/
VCR on the Remote so that VCR mode indicator goes off from
the display panel. (The TV broadcast being recorded
disappears.)
If you are using the AV connection (
from the VCR, change the TV's input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
Second Audio Recording
This VCR's built-in MTS decoder enables reception of
Multichannel TV Sound broadcast. To record a SAP program
received, set "2ND AUDIO RECORD" to "ON" (
) on the VCR repeatedly until the
7
) on the Remote or STOP/EJECT
8
pg. 5) to view pictures
pg. 13).

Timer Recording

Up to 8 timer recording programs can be made using express
timer programing method as far as a year in advance. Remember,
the clock must be set before you can program the timer.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
NOTES:
If all the 8 programs have already been set, "PROGRAM FULL"
appears on the TV screen.
After timer recording is completed, the VCR turns off
automatically.
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
again to this VCR after the power failure, this VCR starts the
Plug&Play setting automatically to restore the clock time and
channel setting. If the clock time and channel setting are
restored correctly, each timer program you have made will start
at its start time unless its end time has elapsed.
If the tape reaches its end during timer recording, the recording
stops and " ", "
#
TIMER to disengage timer, then press STOP/EJECT (0) on
the VCR to eject the cassette or press POWER 1 then press
REW (3) to rewind the tape.

Express Timer Programing

Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.
A
Press PROG. on the Remote to access the Program screen.
B
Press START /
and/or "4"), STOP
"2" and/or "5"), DATE
key "3" and/or "6") or CH
repeatedly to enter the start time, stop
time, date or channel.
Press and hold START
/ to increase the time in 30-minute intervals.
To set the tape speed, press SP/EP.
To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (M-F) (Number key "8") or WEEKLY (Number
key "9"). Pressing the button again makes the "DAILY" or
"WEEKLY" display disappear.
C
Press OK or PROG..
If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, see "Program overlap warning display" (
D
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.
— 10 —
" and " $" on the display panel blink. Press
(Number key "1"
/ (Number key
START
/ (Number
– –:– –AM
DATE
/
– –/– –/– –
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
/ or STOP
CONTINUED ON NEXT PAGE
PROGRAM 1
STOP
– –:– –AM
CH
– – – SP
pg. 11).
" is
#