Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SMART Adio 340
Summary of Contents for SMART Adio 340
- Page 1 SMART Audio™ 340 Classroom amplification system Installation guide...
- Page 2 SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
-
Page 3: Table Of Contents
Installing the room module ..................10 Installing the control unit ....................13 Installing the microphone charging cradle..............17 Chapter 3: Integrating your SMART Audio system with your SMART Board interactive whiteboard system ............. 19 Appendix: Hardware environmental compliance...............21 Waste Electrical and Electronic Equipment regulations (WEEE directive) ....21 Batteries ........................21... - Page 4 1012080 Rev A1...
-
Page 5: Chapter 1: Planning Your Installation
Chapter 1 Planning your installation Product components This guide describes the installation of the following SMART Audio™ classroom amplification system components: • Control unit – Mounting plate – Cable cover – Power cable • Room module – Mounting plate –... -
Page 6: See Page
NOTE Your SMART Audio system doesn’t include Cat 5e cable or speaker wire, unless you order it specifically with your classroom amplification system. You can purchase these wires and cables from most professional installers. - Page 7 CH AP TE R 1 Planning your installation Choosing a location for the control unit Install the control unit on the wall at the front of the room where the presenter can easily access it. Select a location that is within 8' (2.4 m) of a power outlet and within 50' (15.2 m) of cable distance from the room module.
- Page 8 CH AP TE R 1 Planning your installation SMART Audio system cabling diagram Speaker wire (See Room module page 5) (See page 10) Ex pa n sio n S en sors N.C . C OM N.O. P A G I NG...
-
Page 9: Chapter 2: Installing Your Smart Audio System
Chapter 2 Installing your SMART Audio system Installing speaker wires and Cat 5e cables Run the speaker wires to the speakers and run the Cat 5e cable between the control unit and room module before you begin installation. If you want to place the wires and cables out of sight, run the cables in the walls and ceiling. - Page 10 2. Pull an RCA cable from the room module location to each expansion sensor location. To install audio cables from your SMART Board interactive whiteboard system If you have a SMART Board interactive whiteboard system, pull audio cables from the audio out connectors on your projector to the control unit location.
-
Page 11: Installing Ceiling Speakers
CH AP TE R 2 Installing your SMART Audio system Installing ceiling speakers For each of the four speakers, use the ceiling speaker cut-out template to cut a hole in a ceiling tile, and then assemble the ceiling tile bridge, secure the speaker to the ceiling tile and replace the tile. - Page 12 CH AP TE R 2 Installing your SMART Audio system 3. Slide the ceiling tile and tile bridge onto the speaker. 4. Turn the ceiling speaker clamps so they’re perpendicular to the speaker. 5. Tighten the four speaker clamp screws with a screwdriver until they firmly clasp the ceiling tile.
-
Page 13: Installing Wall Speakers
CH AP TE R 2 Installing your SMART Audio system Installing wall speakers For each of the four speakers, install the wall speaker bracket on the wall, and then attach the speaker to the bracket. To install the wall bracket on the wall 1. -
Page 14: Installing The Room Module
CH AP TE R 2 Installing your SMART Audio system Installing the room module Install the room module mounting plate on the ceiling or on a ceiling tile, and then attach the room module and the cable cover to the mounting plate. - Page 15 CH AP TE R 2 Installing your SMART Audio system 3. Screw the mounting plate to the ceiling with the included screws and drywall anchors. Attaching the room module to the mounting plate Attach the room module to the mounting plate, and then connect the wires, cables and safety tether.
- Page 16 CH AP TE R 2 Installing your SMART Audio system Connecting cables to the room module For more information, see the SMART Audio system cabling diagram on page 4. Room module connectors General purpose 6-12 V DC input Expansion sensors connectors...
-
Page 17: Installing The Control Unit
CH AP TE R 2 Installing your SMART Audio system Installing the control unit Install the mounting plate, and then attach the control unit and cable cover to the mounting plate. Select a location on the wall that is within 8' (2.4 m) of a power outlet. - Page 18 3. Connect the included USB cable from the control unit to your computer. 4. If you have a SMART Board interactive whiteboard system, connect the RCA cable (with two connectors on each end) from your projector to the Aux In 1 connectors.
- Page 19 CH AP TE R 2 Installing your SMART Audio system To install the power supply 1. Hold the power supply mounting plate against the wall where you plan to install it, and then mark the anchoring holes on the wall with a pencil.
- Page 20 CH AP TE R 2 Installing your SMART Audio system 6. Push the cables into the cable slots in the mounting Cable slot bracket. Cable slot 7. Attach the power supply cover to the bracket. 1012080 Rev A1...
-
Page 21: Installing The Microphone Charging Cradle
CH AP TE R 2 Installing your SMART Audio system Installing the microphone charging cradle You can install the microphone charging cradle on the wall or place it on a table. If you’re mounting the charging cradle on the wall, install its mounting plate, and then attach the charging cradle to the mounting plate. - Page 22 CH AP TE R 2 Installing your SMART Audio system 1012080 Rev A1...
-
Page 23: Chapter 3: Integrating Your Smart Audio System With Your Smart Board Interactive Whiteboard System
SMART software Your SMART Audio classroom amplification system operates without additional software. However, installing the SMART Audio software suite enables you to do the following: • Access SMART Audio volume settings through SMART Notebook™ collaborative learning software or a desktop icon. - Page 24 CH AP TE R 3 Integrating your SMART Audio system with your SMART Board interactive whiteboard system 4. If your computer doesn’t have SMART Notebook software installed, place the included SMART Notebook software CD in your computer. 5. Follow the on-screen instructions to install SMART Notebook software.
-
Page 25: Appendix: Hardware Environmental Compliance
Appendix Hardware environmental compliance SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner. Waste Electrical and Electronic Equipment and Battery regulations (WEEE and battery directive) Electrical and electronic equipment and batteries contain substances that can be harmful to the environment and to human health. - Page 28 SMART Technologies smarttech.com/support smarttech.com/contactsupport 1012080 Rev A1...