Page 2
KWANG YANG MOTER CO .,LTD NO.35 Wan Hsing Street,San Min District Kaohsiung, Taiwan, Republic Of China Telephone : 886-7-3822526 Fax : 886-7-3950021 Printed in Taiwan...
Page 3
Battery & EFI Damage Alert Dangerous Alert CAUTION: POTENTIAL HAZARD Operating your UTV in areas with tall or loose vegetation. CELP indication : WHAT CAN HAPPEN If brightness, it indicates that a fault has Combustible materials such as tall grass or been detected in the vehicle 's EFI or reeds .exposed to the exhaust system’s hot electrical system.
Page 4
Dear KYMCO UXV 700 i Users: Thank you for purchasing this KYMCO UXV 700i and welcome to the family of KYMCO UXV 700 i riders. To enjoy safety and more pleasant riding, become thoroughly familiar with this owner manual before you ride the UXV 700i.
Page 8
This vehicle can be dangerous to operate. A impact or rollover can occur quickly. even during routine maneuvers such as turning and driving on hills or over obstacles, if you fail to take proper precautions. For your safety, understand and follow all the warnings contained in this Owner’s Manual and labels on this vehicle.
Page 9
This vehicle is not a toy and can be dangerous to operate. ●Always go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating this vehicle. ●Never operate on too rough, slippery, or loose terrain. ●Always follow proper procedures for turning as represent in this manual.
Page 10
Safety Watchful Always read the owner’s manual carefully and follow the operating ● procedures described. Pay special attention to the warnings contained In the manual and on all labels. Never operate this vehicle with the canopy frame removed. ● Always wear the seat belt, helmet and eye protection when driving.
Serial Number Locations This vehicle has 2 serial numbers:The frame number and Engine serial number. The frame number is located on the frame near right front wheel place. Frame Number...
Page 12
Serial Number Locations The engine serial number is located on the right side of the engine crankcase. Engine Serial Number...
Page 13
Ignition Switch Key/Fuel Cap Key Right Glove Compartment Key Four keys come with this vehicle. Keep the spare in the safe place. Note: Some models with just one type of Fuel Cap Key key for the whole vehicle. Right Glove Compartment Key →2PCS Ignition Switch Key→2PCS...
Page 14
Location Of Parts (1) 1.Right Head Pillow 2.Right Seat 3.Right Tail /Brake Light 4.Left Head Pillow 5. Left Seat 6.Left Tail /Brake Light...
Page 15
Location Of Parts (2) 07.Seat Belts 08.Cargo Bed 09.Headlights 10.Battery 11.Steering Wheel 12.Cab Frame 13.hands Bars 14.Bumper 15.Tool or Parts Box (Under the operator’s seat)
Page 16
Location Of Parts (3) 16.Under-Hood 17.Hands Bars 18.Fuel Tank Cap 19.Muffler& Spark Arrester 20. Latch Handles...
Page 17
Location Of Parts(4) 21.Right Glove Compartment 22. Auxiliary Outlet 23.Speedometer 24. Center Glove Compartment 25.Shifting The Automatic Transaxle 26.Ignition Switch 27.Steering Wheel 28.Brake Pedal 29.Throttle Pedal...
Features And Controls Fuel Lever Inspection/Refilling Check if fuel is sufficient. If the fuel gauge pointer is E(flash).refill nonleaded gasoline as soon as possible. (Refilling Method) 1.Turn the tank cap counterclockwise with hand to open the cap. 2.Use only nonleaded gasoline. OPEN CLOSE 3.Turn the fuel tank cap clockwise to tighten...
Features And Controls Indicator Lights The indicator lights on the console display: 1. Lower Gear 2. High Gear 3.Neutral Gear 4.Reverse Gear 5. Parking Gear 6. High Beam Indicator Light 7. FI System Indicator Light 8.Lock:( Differential Lock Indicator Light )9.Battery Low Voltage Indicator Light 10. High Coolant Temperature Indicator Light 11.
Page 32
Features And Controls Instruments and Indicators 1.Speedometer 2. Km/h or Mph 3. Clock 4. 4WD 5.Fuel Gauge 6.ODO Meter 7. Adjust Button 8.Engine Tachometer...
Page 33
Features And Controls Operation Instruction for Multi-meter Button A (MODE) Button B (SET)
Page 34
Features And Controls Operation Instruction for Multi-meter Press and hold button A until 2 seconds over. Shift the unit mph or km/h Button A (MODE)
Page 35
Features And Controls Operation Instruction for Multi-meter Press and hold button B until 2 seconds over. Shift function to ODO or TRIP Button A (SET)
Page 36
Features And Controls Operation Instruction for Multi-meter Press and hold button A and B until 2 seconds over. Simultaneously to reset to zero when at TRIP function. Button B (SET) Button A (MODE)
Page 37
Features And Controls Operation Instruction for Multi-meter Press and hold button A and B until 5 seconds over . when at ODO function then you can see clock position is flash word . Button B (SET) Button A (MODE)
Page 38
Features And Controls Operation Instruction for Multi-meter When you seeing clock position is flash word . You can start setting hour item. Press button B adjust correct hours then Press button A you can see minute position is flash. adjust correct minute. Waiting for 2second .finish times setting.
Features And Controls Auxiliary Outlet The 12-volt receptacle has spade connections on the back that may be used to power an auxiliary light or other optional accessories or lights. The connections are behind the console,under the hood. Auxiliary Outlet...
Features And Controls Seat Removal • Pull up on front of seat it toward the front of vehicle. • Install the seat by sliding the tabs into the rear of the seat base. • Push down firmly on the front of the pins are fully seated into the grommets.
Page 41
Features And Controls Pillows adjust If you want to adjusting your pillows. Remove the three bolts and adjusting you need pillow position . Tighten three bolts.
Features And Controls Gear Selector Maintaining shift linkage adjustment is 1.Lower Gear important to assure proper 2.High Gear transmission function . 3.Neutral Gear See your dealer if you experience any 4.Reverse Gear shifting problems. 5.Parking Gear To change gears,stop the vehicle and with the engine idling, move the lever to the desired gear.
Page 43
Features And Controls Switches Ignition Switch The ignition switch is a three-position,key- operated switch, The key can be removed from the switch when it is in the OFF position. Electrical circuits are on Electrical equipment can be used. OFF: Engine off .All electrical circuits are off except Acc.12V START: Electrical starter is engaged by holding ignition switch key in this...
Page 44
Features And Controls Switches Light Switch • The ignition switch key must be in the ON position to operate the headlights. • The switch has 4 positions. 1:Light off -At this position , light is turn off. 2: Position light - At this position , light is turn off 3.LO Headlight Beam- When you select this position .
Page 45
Features And Controls Switches Drive Select Switch The 2WD/4WD allows the operator to operate the vehicle in either two-wheel drive (rear wheel) or four wheel drive(all wheels) For normal riding on flat, dry, hard surfaces, two-wheels drive should be sufficient. In situations when additional traction is necessary, four-wheel drive would be the desired choice.
Page 46
Features And Controls Differential Lock lever and indicator The vehicle is equipped with a lockable differential that allows the operator to choose between an open differential or a closed differential in low traction situations. To lock the differential push and turn the switch to the 4WD lock position.
Page 47
Features And Controls Brake Pedal(1) Depress the brake pedal to slow or stop or stop the vehicle. Throttle Pedal(2) Push the pedal down to increase engine speed .Spring pressure returns the pedal to the rest position when released. Always check that the throttle pedal returns normally before starting the engine.
Page 48
Features And Controls Parking Brake Release(3) To release the parking brake, pull the release handle Spring pressure helps return the lever to the released position .make sure the parking brake lever is functioning properly before each operation.
Page 49
Features And Controls Cargo Bed (Lift and lower the cargo bed) To lift Push the cargo bed release lever to right side, then slowly lift up cargo bed until it stop. To lower Lower the cargo bed slowly to its original position and be sure the it is locked into place.
Page 50
Features And Controls Cargo Bed(Open and close the tailgate 1) To open---(1) Unlock the latches,and then lower the tailgate. Latch(x2) Pull...
Page 51
Features And Controls Cargo Bed(Open and close the tailgate 2) To close Place the tailgate in the original position ,and then hook the latches.
Page 52
Features And Controls Under-Hood (To Open) Unhook the hood latches and 3 and then slowly tilt the hood up until it stops. Latch x2...
Page 53
Features And Controls Under-Hood (To Close) Lower the hood slowly to its original position and then hook the hood latches . Latch x2...
Page 54
How to operate Daily Safety Checks Check the following items each day before operation. 01.Fuel---------------------Enough fuel in tank,no leaks. 02.Engine Oil-------------Oil lever between lever holes(when engine is cold),no leaks. 03.Tires --------------------Air pressure(when cold)and check tires cracks, damage or abnormal wear.Check for any imbedded stones or other foreign particles in tread.
Page 55
How to operate Driving Safely(Driving procedures) 1.Sit in the driver’s seat and fasten the seat belt. 2.Wear the helmet and eye protection when driving. 3.After staring the engine and allowing it to warm up,shift the transmission into gear. 4.Check your surroundings and determine your path of travel. 5.Release the parking brake.
Page 56
How to operate Start the Engine WARNING Never run the vehicle in a closed area, such as a garage Exhaust gases contain carbon monoxide, a colorless, odorless, poisonous gas. Breathing exhaust gas leads to carbon monoxide poisoning, asphyxiation, and death. 1.Wear the seat belts, helmets and eye protections.(both operator and passenger) 2.Set the parking brake.
Page 57
How to operate Start the Engine CAUTION Do not run the starting attempt. The starter motor may overheat causing severe starter motor damage. Allow 15 seconds between starting attempts to allow the starter motor to cool. Braking/Stopping Always allow plenty of room and time to stop smoothly. Sometimes quick stops are inevitable’...
How to operate Parking Parking involves flowing the previous rules for braking;then : 1.After the vehicle stops,shift into neutral gear. 2.Set the parking brake. 3.Turn off the ignition key. 4.If you have to park on the hill,shift to low range,set the parking brake,and block the wheel on the downhill side.
Page 59
How to operate Driving Uphill whenever travel straight uphill, follow these precautions: 1.Always travel straight uphill. 2.Avoid steep hills(15° maximum) 3.Keep both feet on the floor. 4.Proceed at a steady rate of speed and throttle opening. NEVER OPERATE UP OR DOWN HILLS STEEPER THAN 15°...
How to operate Crossing Water UXV700i can only operate in water up to its floorboard.Stay away from fast moving rivers. This vehicle’s tires can be buoyant.In deep water,the vehicle may lose traction due to floating. 1.Physically check the depth and current of the water, especially if you can not see the bottom.Also,check for boulders,logs,or any other hidden obstacles.
How to operate Driving in Reverse Follow these guidelines when operating in reverse: 1.Back slowly. 2.Apply the brakes lightly for stopping. 3.Avoid turning at sharp angles. 4.Always avoid backing downhill. 5.Never open the throttle suddenly while backing. 6. Always inspect left and right fields of vision before backing.
Emission Control System Crankcase Emission Control System This engine is equipped with a closed crankcase system . Blow-by gases forced back to the combustion chamber by the intake system. The system does not allow the blow-by gases to enter the atmosphere. Exhaust Emission Control System The emissions from the exhaust of this vehicle are controlled by engine design,including factory-set fuel delivery and ignition.KYMCO Exhaust...
Page 63
Emission Control System Spark Arrester Your UXV 700i has a spark arrester. The spark arrester be installed and functional when the vehicle operated on public lands. Clean method Remove method Use the iron brush cleaning remove 3 bolts carbon on the spark arrester...
Maintenance And Lubrication Engine Oil Always check and change the oil at the OWNER MANUAL standard intervals. The oil tank is located under the seat. 110 F 1.Position the vehicle on the surface. 2.Start the engine and let it idle for 20~30seconds. 3.Stop the engine and remove the seat.
Page 65
Maintenance And Lubrication Engine Oil 1.Engine oil level measurement A. Place the machine on a level place. B. Warm up the engine for several minutes and stop it. C. Check the oil level through the inspection window. D. The oil level should be between the maximum (H) and minimum (L) marks. If the level is low, add oil to raise it to the proper level.
Page 66
Maintenance And Lubrication (2) oil drain bolt Engine oil replacement and oil filter cleaning 1. Place the machine on a level place. 2. Warm up the engine for several minutes and stop it. 3. Place a container under the engine. 4.
Page 67
Maintenance And Lubrication NOTE: Skip steps E to I if the oil filter cartridge is not being replaced. Remove the oil filter cartridge with an oil cartridge wrench. oil filter cartridge remove lock...
Page 68
Maintenance And Lubrication Changing the rear gear box oil Recommended oil : SAE 80 Oil quantity : 1. Place the vehicle on the a level surface. Periodic oil change 2. Place a container under the rear gear box 0.23L to collect the used oil. 3.Remove the rear gear box oil drain bolt(1) and rear gear box oil filler cap (2).
Page 69
Maintenance And Lubrication Changing the front gear box oil 1. Place the vehicle on the a level surface. 2. Place a container under the front gear box to collect the used oil. 3.Remove the front gear box oil drain bolt(1) and front gear box oil filler bolt (2).
Page 70
Maintenance And Lubrication BRAKE FLUID INSPECTION Check if the fluid level is below the lower level mark through the inspection window. WARNING POTENTIAL HAZARD Brake fluid contacting the skink or eyes. WHAT CAN HAPPEN May cause irritation. HOW TO AVOID THE HAZARD Avoid contacting brake fluid with the skin or eyes.
Page 71
Maintenance And Lubrication Air Cleaner Remove the center cover fasteners. Remove gear selector screw and center cover.
Page 72
Maintenance And Lubrication Air Cleaner Remove air cleaner cover. Remove air filter element.
Page 73
Maintenance And Lubrication Air Cleaner Using high pressure air to clean air filter element . Inspect the air filter element and replace it if damaged.
Maintenance And Lubrication Battery Remove 1. Make sure the ignition switch is OFF. 2. Remove the under-hood hook & bolts. 3. Remove the battery cover screws. 4. Disconnect the negative ( ) terminal lead (1) from the battery first, then disconnect the positive (+) terminal lead (2).
Maintenance And Lubrication Fuse Replacement (1) (2) (3) (4) (5) (6) The fuse box stored in the battery compartment. To replace a fuse: 1. Make sure the ignition switch is OFF. 2. Remove the under-hood hook& pu bolts. 3. Open the fuse box cap. 4.
Page 76
Maintenance And Lubrication Cooling System Inspection NOTE: A permanent type of antifreeze is installed in the 1. Remove the under-hood hook& pu bolts. cooling system when shipped.It is colored green 2. Check the coolant level in the coolant and contains ethylene glycol.It is mixed.It is mixed reservoir when the engine is cold as the at 50% with water and has a freezing point of coolant level will vary with engine...
Maintenance And Lubrication Wheel Installation Wheel Removal When reinstalling a wheel, tighten the wheel nuts in 1.Elevate the wheel by placing a suitable a crisscross(rather than a circular)pattern. stand under the frame. Be sure the tapered a side of the wheel nuts(1)face 2.Remove the nuts from the wheel.
Page 78
Maintenance And Lubrication NOTE: WARNING The arrow mark on the tire must point POTENTIAL HAZARD toward the rotating direction of the wheel. Installing wheels improperly. WHAT CAN HAPPEN A wheel may come loose, possibly leading to an accident. HOW TO AVOID THE HAZARD Carefully follow the instructions in this Owner's Manual when installing.
Maintenance And Lubrication Spark Plug Inspection Before installing the spark plug, measure the The spark plug is an important engine electrode gap with a feeler gauge and adjust to component and is easy to inspect. specification. The condition of the spark plug can indicate the condition of the engine.
Maintenance And Lubrication Tool Kit The tool kit put down location at Right Glove Compartment . The tool kit includes the following items: (1) Hexagon wrench (3) (5) (1) (2) (2) Spark plug wrench (3) 8/12;10/14;17/19 mm wrench (4) Screwdriver (5) Screwdriver handle (6) Tool bag (7)Air pressure gauge...
Specifications UXV700 i (OFF ROAD) MODEL DIMENSIONS: OVERALL LENGTH 113 in(2870 mm) OVERALL WIDTH 59.06 in(1500 mm) OVERALL HEIGHT 72.84 in(1850 mm) SEAT HEIGHT 31.69 in(805 mm) WHEELBASE 75.20 in(1910 mm) GROUND CLEARANCE 12.21 in(310 mm) MINMUN. TURNING RADIUS 181.10 in(4600 mm) BASIC WEIGHT: WITH OIL AND FULL FUEL TANK 650kg...
Page 82
Specifications UXV700 i (OFF ROAD) MODEL ENGINE GEAR BOX: CAPICITY/EXCHANGE/TYPE 2.9L/2.4L/5W-30 FRONT GEAR BOX: CAPICITY/EXCHANGE/TYPE 270ML/250ML/SAE80# REAR GEAR BOX CAPICITY/EXCHANGE/TYPE 250ML/230ML/SAE80# AIR FILTER: SPONGE ELEMENT FUEL: TYPE UNLEADED GASOLINE FUEL TANK CAPACITY 8.32 gal (32 L) THROTTLE BODY: TYPE/MANUFACTURER PTA1/KYMCO SPARK PLUG: TYPE/MANUFACTURER CR7E-NGK...
Page 83
Specifications MODEL UXV700 i (OFF ROAD) TRANSMISSION: PRIMARY REDUCTION SYSTEM V-BELT SHAFT DRIVE SECONDARY REDUCTION SYSTEM TRANSMISSION TYPE: TIRE: TYPE TUBELESS SIZE(FRONT) 25x 8-12, 26X9-14 SIZE(REAR) 25x10-12, 26X11-14 WHEEL MATERIAL STEEL or alluminum PRESSURE FR/RR 0.7/0.98(kgf/cm2) OR 10/14 psi BRAKES: SYSTEM FRONT AND REAR UNIFIED TYPE(FRONT)
Page 84
Specifications UXV700 i ( OFF ROAD) MODEL WHEEL TRAVEL: FRONT WHEEL TRAVEL 190mm REAR WHEEL TRAVEL 190mm ELETRICAL: IGNITION SYSTEM DC, ECU AUTOMATIC CONTROL GENERATOR SYSTEM A.C.MAGNETO BATTERY TYPE MF-VTX20L BATTERY CAPACITY 12V18AH HAEDLIGHT TYPE: BULB VOLTAGE WATTAGE X QUANTITY: HAEDLIGHT: 12V35/35W*2 REAR LIGHT...
Page 85
Specifications MODEL UXV700 i (OFF ROAD) SPECIFIED FUSES: MAIN FUSE FAN MOTER IGNITION LIGHT DC12VPOWER FUEL SPARE...
Page 93
By KWANG YANG Motor Co., Ltd. First Edition, JUN 2013 All rights reserved. Any reproduction or unauthorized use without the written permission of KWANG YANG Motor Co., Ltd. is expressly prohibited. T200 -UBADAA -US-A5...
Need help?
Do you have a question about the UXV 700i and is the answer not in the manual?
Questions and answers
Where is engine fan located?
Where is the engine fan located?
How to adjust my carberator , it’s to rich in fuel.