Jacobsen Eclipse 2 Technical Manual

Jacombsen eclipse 2

Hide thumbs Also See for Eclipse 2:

Technical manual (171 pages)

Technical manual (174 pages)

100

Table of Contents

Quick Links

Chapters

Table of Contents

Need help?

Do you have a question about the Eclipse 2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Jacobsen Eclipse 2

Page 1 63344 – Eclipse 2 118, 18” 15 Blade Reel, Battery Pack 63336 – Eclipse 2 118F, Floating 18” 11 Blade Reel, Gen-Set 63345 – Eclipse 2 118F, Floating 18” 11 Blade Reel, Battery Pack 63337 – Eclipse 2 118F, Floating 18” 15 Blade Reel, Gen-Set 63346 –...
Page 2: Service Parts
Jacobsen Dealer. Suggested Stocking Guide To Keep your Equipment fully operational and productive, Jacobsen suggests you maintain a stock of the more commonly used maintenance items. We have included part numbers for additional support materials and training aids. To order any of the following material: 3.
Page 3: Table Of Contents
Table of Contents 1 SAFETY 8 FLOATING HEAD REEL ADJUSTMENTS Operating Safety ..... . 4 General ......40 Important Safety Notes .
Page 4: Safety
Only accessories Section 5.9 . attachments approved by Jacobsen. 20. Before you clean, adjust or repair this equipment, 7. Stay alert for holes in the terrain and other hidden stop the engine, disconnect the spark plug wire, and hazards.
Page 5: Important Safety Notes
Adjustments and maintenance should always be performed by a qualified technician. If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the latest methods to service this equipment and can provide prompt and efficient service.
Page 6: Specifications
SPECIFICATIONS SPECIFICATIONS PRODUCT IDENTIFICATION _________________________________________________ ® ® 63334......Eclipse 118 base unit with 18 in. 63349......Eclipse 122F base unit with (457 mm) 11 blade reel and floating 22 in. (457 mm) 11 blade InCommand™ control system. reel and InCommand™ control Gen-Set power module.
Page 7: Mower
SPECIFICATIONS MOWER __________________________________________________________________ Reel........7, 9, 11, or 15 blades, hardened Low Profile ....1/8” - 7/32” (3.2 - 5.6 mm) cut high manganese carbon steel. Tournament....3/32” - 5/32” (2.4 - 4 mm) cut Reel Diameter ....5 in. (127 mm) Super Tournament ..
Page 8: Battery Power Module
For optimum range and performance These batteries have the same dimensions and amp- use batteries that equal or exceed the Amp-hour rating hour ratings, but have not been tested by Jacobsen, and listed. no recommendation is stated or should be implied.
Page 9: Accessories & Support Literature
ACCESSORIES & SUPPORT LITERATURE _____________________________________ Contact your area Jacobsen Dealer for a complete listing of accessories and attachments. CAUTION Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the equipment. Accessories Solid Rollers Lapping Compound (180 grit) ........
Page 10: Declaration Of Conformity
Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des Herstellers ▪ Jacobsen, A Textron Company Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo completo del fabbricante ▪...
Page 11 Plaats en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la déclaration ▪ Jacobsen, A Textron Company Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪ A nyilatkozat kelte (hely és idő) ▪ Luogo e data della dichiarazione ▪...
Page 12 Comunidade. VP of Engineering Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze Jacobsen, A Textron Company dosarul tehnic şi este stabilită în Comunitate. 11524 Wilmar Blvd, Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá...
Page 13: Decals
DECALS DECALS DECALS _________________________________________________________________ Familiarize yourself with the following decals. They are critical to the safe operation of the mower. REPLACE DAMAGED DECALS IMMEDIATELY. DANGER To prevent injury, disengage all drives, engage parking brake, turn off key switch and disconnect power connector before working on machine emptying...
Page 14 DECALS Familiarize yourself with the following decals. They are critical to the safe operation of the mower. REPLACE DAMAGED DECALS IMMEDIATELY. Read the manual before adjusting front roller weight. 4172240 Key Switch Off Position Run Position Energize Unit 4265172 Reel Switch 4265170 Disengaged Parking...
Page 15 DECALS To Engage Traction. 1. Slide bail to the left. 2. Squeeze bail to handle.
Page 16: Controls
CONTROLS CONTROLS ICONS ___________________________________________________________________ O.P.C. Traction Parking Brake Throttle Drive Power Off Fast Slow Engaged Disengaged Power On Slide Bail Left Power Up Squeeze bail to handle WARNING Never attempt to operate the machine unless you have read the Safety and Operation Manual, the Parts and Maintenance Manual and know how to operate all controls correctly.
Page 17: Lcd Display
CONTROLS LCD DISPLAY _____________________________________________________________ The LCD displays current functional values for the operation of the Eclipse mower and sounds one of three types of audible alerts. The LCD operates in one of two modes, Operator Mode (Default), and Maintenance Mode. Use of Maintenance mode requires a four digit pin number.
Page 18 CONTROLS Operator Mode is used by the operator for system voltage information, travel speed, FOC setting, reel speed, and total hours on mower. Press the orange buttons (K and L) on the front handle cover to toggle between the different displays. Operator Mode is view only, only screen illumination mode can be changed.
Page 19 CONTROLS Maintenance Mode is used to set and adjust all functional values for the Eclipse Mower. LCD displays available in Maintenance Mode are, maintenance hours, backlap, system voltage, travel speed, set FOC, reel speed, traction motor current draw, reel motor current draw, total motor current draw, set mow speed, set reel speed, set power source, set number of reel blades, calibrate speed paddle, calibrate bail lever, set display units, and factory reset.
Page 20 NOTE: The default PIN for Maintenance Mode is 6789. The Maintenance Mode PIN can be customized to a setting of your choice. Please contact your Jacobsen Dealer or Jacobsen Technical Support (1800-848-1636 Option 2) for complete instructions. Maintenance Hours - System can track up to 999.9 hours for maintenance purposes.
Page 21 CONTROLS Display Description Gen-Set Power Module - Used to indicate the gen-set power module is installed on the mower. This setting is used by system controllers and does not affect operation of mower. Do not operate mower with incorrect power module setting. Press the black button (J) to toggle between the power module settings.
Page 22: Frequency Of Cut
CONTROLS FREQUENCY OF CUT ______________________________________________________ The FOC (Frequency of cut) is the distance, in inches Adjust FOC with Reel Speed Setting (mm), the machine travels forward between reel blades 1. Using the FOC charts, determine the maximum mow contacting the bedknife. The FOC can be adjusted either speed and fixed reel speed required for the desired by changing the Fixed FOC setting or by changing the FOC.
Page 23 CONTROLS 15 Blade Reel FOC Table Product No 63339, 63341, 63335, 63337, 63348, 63350, 63344, 63346 (Standard Reel) Reel RPM Speed 1800 1850 1900 1950 2000 2050 2100 2150 2200 2.00 0.078 0.076 0.074 0.072 0.070 0.069 0.067 0.065 0.064 (3.22) (1.987) (1.933)
Page 24 CONTROLS 11 Blade Reel FOC Table, Product No. 63334, 63336, 63338, 63340, 63347, 63349, 63343, 63345 (Standard Reel) Reel RPM Speed 1800 1850 1900 1950 2000 2050 2100 2150 2200 0.107 0.104 0.101 0.098 0.096 0.094 0.091 0.089 0.087 (3.22) (2.709) (2.636) (2.567)
Page 25 CONTROLS 9 Blade Reel FOC Table, Product No. 63340, 63349 (Optional Reel) Reel RPM Speed 1800 1850 1900 1950 2000 2050 2100 2150 2200 0.130 0.127 0.124 0.120 0.117 0.114 0.112 0.109 0.107 (3.22) (3.311) (3.222) (3.137) (3.057) (2.98) (2.908) (2.838) (2.772) (2.709)
Page 26 CONTROLS 7 Blade Reel FOC Table, Product No. 63342, 63351 (Standard Reel) and 63340, 63349 (Optional Reel) Reel RPM Speed 1800 1850 1900 1950 2000 2050 2100 2150 2200 0.168 0.163 0.159 0.155 0.151 0.147 0.144 0.140 0.137 (3.22) (4.258) (4.142) (4.033) (3.93)
Page 27: Gas Power Module Controls
CONTROLS GAS POWER MODULE CONTROLS ___________________________________________ M. Engine Switch – The engine switch enables and disables the engine ignition system. The engine switch must be in the ON position for the engine to run. Turning the engine switch to the OFF position stops the engine.
Page 28: Operation
OPERATION OPERATION DAILY INSPECTION________________________________________________________ 2. Make sure the mower is adjusted to the required cutting height. CAUTION 3. Make sure the machine is lubricated and the The daily inspection should be performed only with transport tires are properly inflated. the parking brake engaged, and power connector 4.
Page 29: Operating Procedures
Each condition will require certain adjustments or are extremely sharp and can cause serious injuries. precautions. Only use accessories and attachments approved by Jacobsen. 7. Be aware of mower discharge direction and never direct discharge of material toward bystanders. Never allow anyone near the machine while in operation.
Page 30: Starting/Stopping
OPERATION STARTING/STOPPING _____________________________________________________ 1. Prepare power module to energize unit. Battery Power Module: Disconnect battery charger and connect power connector. Gen-Set Power Module: a. Check oil level and fuel supply then open fuel valve lever (P). b. Move the choke lever (N) to the CLOSED position.
Page 31: Mowing
OPERATION MOWING _________________________________________________________________ 4. To assure complete, even cutting, overlap swaths by 1 to 2 in., (25 to 50 mm), then make one or more WARNING passes around the perimeter of the green to clean ragged edges and separate the putting green To prevent serious injuries, keep hands, feet, and surface from the apron.
Page 32: Transport Wheels (Optional)
OFF, and disconnect power connector. Transport wheels are optional accessories available through your Jacobsen Dealer. Traction wheels are recommended when not using the Mower Caddy to move the mower from green to green. 1. Push and hold the kickstand against the ground then pull the mower handle, by the lift point, back until the mower rests on the stand (S).
Page 33: Grass Catcher
OPERATION GRASS CATCHER _________________________________________________________ 1. When the basket is about two thirds (2/3) full of grass clippings, move the mower off the green. WARNING 2. Stop on a flat surface, disengage O.P.C. bail, To prevent serious injury, always disengage engage parking brake, turn key switch OFF, and O.P.C.
Page 34: Adjustments (All Units)
1. Adjustments and maintenance should always be machine. performed by a qualified technician. If proper adjustment cannot be made, contact an authorized 4. Do not change speed limit settings or overspeed the Jacobsen Dealer. drive motors. 2. Replace, adjust, worn damaged components.
Page 35: Handle
ADJUSTMENTS (ALL UNITS) HANDLE _________________________________________________________________ 1. To adjust the angle of the handle bar (F), loosen screw (D) on both sides of the mower and adjust the handle bar to the desired position. 2. After adjusting handle bar, adjust bracket (E) so that the handle bar just rests on the bottom of the slot in bracket.
Page 36: Front Roller Weight
ADJUSTMENTS (ALL UNITS) FRONT ROLLER WEIGHT ___________________________________________________ The weight on the front roller is adjustable. Adjust the front roller weight as required to meet your turf needs. CAUTION To prevent injury or property damage, place mower on kickstand or support mower handle before removing battery pack.
Page 37: Torque Specification
All torque values included in these charts are approximate and are for reference only. Use of these torque values is at your sole risk. Jacobsen is not responsible for any loss, claim, or damage arising from the use of these charts.
Page 38: Fixed Head Reel Adjustments
1. Adjustments and maintenance should always be machine. performed by a qualified technician. If proper adjustment cannot be made, contact an authorized Do not change speed limit settings or overspeed the Jacobsen Dealer. drive motors. 2. Replace, adjust, worn damaged components.
Page 39: Bedknife Adjustment
FIXED HEAD REEL ADJUSTMENTS BEDKNIFE ADJUSTMENT ___________________________________________________ a. Slide a feeler gauge or shim stock 0.001 - 0.003 NOTICE in., (0.025 - 0.075 mm) between the reel blade and the bedknife. Do not turn the reel. Before tipping mower back for adjustments, the fuel b.
Page 40: Floating Head Reel Adjustments
1. Adjustments and maintenance should always be machine. performed by a qualified technician. If proper adjustment cannot be made, contact an authorized Do not change speed limit settings or overspeed the Jacobsen Dealer. drive motors. 2. Replace, adjust, worn damaged components.
Page 41: Bedknife Adjustment
FLOATING HEAD REEL ADJUSTMENTS BEDKNIFE ADJUSTMENT ___________________________________________________ 1. Read Section 8.2 before making the adjustment. full length of the reel, when the paper is held at 90° to the bedknife. 2. Start adjustment at the leading end of the reel, followed by the trailing end.
Page 42: Cutting Height
FLOATING HEAD REEL ADJUSTMENTS CUTTING HEIGHT _________________________________________________________ Note: Always make the reel to bedknife adjustment 6. Place gauge (E) across bottom of front and rear before adjusting height of cut. (Sections 8.2 and 8.3). rollers near one end of roller. 7.
Page 43: Battery Power Module
BATTERY POWER MODULE BATTERY POWER MODULE SAFETY __________________________________________________________________ Batteries contain dilute sulfuric acid which can result in severe burns. Hydrogen gas is formed within a battery during the charging cycle. Hydrogen in concentrations of 4% and higher are explosive and can be ignited by open flame or an electrical spark. A battery explosion will cause sulfuric acid and battery components to be thrown over a large area with considerable force.
Page 44: Maintenance
BATTERY POWER MODULE MAINTENANCE ___________________________________________________________ Tool List Before charging batteries Insulated wrench, 3/8” Inspect the connector housings of the battery charger Insulated wrench, 11/32” and battery pack for dirt or debris. It is suggested to apply Standard Screwdriver white lithium grease to both terminals to prevent corrosion.
Page 45: Battery Charger
If a new fuse is required, order part number R IA a in fi re , re 4102780 from your Jacobsen Dealer. There is one spare s iz p la n ti p ro ty p...
Page 46: Battery Installation
BATTERY POWER MODULE BATTERY INSTALLATION __________________________________________________ If the batteries have been cleaned and any acid in the battery tray area neutralized, no corrosion to the surrounding area should be present. Any corrosion found should be immediately removed with a putty knife and a wire brush.
Page 47: Replacing Battery Pack
BATTERY POWER MODULE REPLACING BATTERY PACK________________________________________________ The battery pack (A) is designed to be easily lifted out and replaced. This allows the mower to quickly return to service should the batteries become discharged or fail. Additional battery packs are available as an accessory. See Section 2.7 CAUTION To prevent injury or property damage, place mower...
Page 48: Gen-Set Power Module
To order replacement engine manuals contact the engine manufacturer. During the break-in period, Jacobsen recommends the following: The proper break-in of a new engine can make a considerable difference to the performance and life of the 1.
Page 49: Engine Oil Change
GEN-SET POWER MODULE 10.3 ENGINE OIL CHANGE ______________________________________________________ Perform initial oil change after the first 20 hours of Use only SAE 10W30 engine oils with API classification operation. Change oil every 100 hours thereafter. SG.SF/CC.CD. 1. To change engine oil, attach a 7/16 in. (11 mm) i.d. hose (A) to oil drain valve (B).
Page 50: Fuel
GEN-SET POWER MODULE 10.5 FUEL ____________________________________________________________________ Handle fuel with care - it is highly flammable. Use an • Store fuel according to local, state or federal approved container, the spout must fit inside the fuel filler ordinances and recommendations from your fuel neck.
Page 51: Maintenance
If proper adjustments cannot be made, contact an Authorized 4. Use the illustrations in the Parts Catalog as Jacobsen Dealer. reference for the disassembly and reassembly of 2. Inspect the equipment on a regular basis, establish components.
Page 52: Backlapping And Grinding
MAINTENANCE 11.4 BACKLAPPING AND GRINDING _____________________________________________ Check for damage to the bedknife and reel blades. Refer to (Section 6.2). 1. Determine if backlapping or grinding will restore the proper cutting edge. 2. For optimum performance use a bedknife grinder to touch-up the blade then reassemble and adjust the bedknife to the reel as described in (Section 6.2).
Page 53: Storage
MAINTENANCE 11.5 STORAGE ________________________________________________________________ General to slow self discharge. The batteries should be tested or recharged at thirty day intervals. 1. Wash the mower thoroughly and lubricate. Repair and paint damaged or exposed metal. Battery Power Module After Storage 2. Inspect the mower, tighten all hardware, replace 1.
Page 54: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING 12.1 GENERAL________________________________________________________________ The troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed information, contact your area Jacobsen Dealer. Symptoms Possible Causes Action Unit does not have Power Connector Disconnected Connect Power Connector...
Page 55: Maintenance & Lubrication Charts
MAINTENANCE & LUBRICATION CHARTS MAINTENANCE & LUBRICATION CHARTS 13.1 GENERAL ________________________________________________________________ The mower was designed for minimum lubrication. Over 2. Lubricate with grease that meets or exceeds NLGI greasing will produce high loads on the bearings; Grade 2 LB specifications. Apply grease with a thereby reducing the performance of the machine.
Page 56: Lubrication Chart
MAINTENANCE & LUBRICATION CHARTS 13.3 LUBRICATION CHART _____________________________________________________ - Reel Roller Bearing - Reel Motor Bearing Housing - Right Side Traction Drum Bearing Housing - Left Side Traction Drum Bearing Housing - Reel Bearing Housing - Pulley Shaft Bearing - Hub Pulley Shaft Assembly ●...
Page 57: Parts Catalog
Screw, 1/4-20 x 2” Hex Head 14.2 TO ORDER PARTS _________________________________________________________ 1. Write your full name and complete address on the 5. Send or bring the order to an authorized Jacobsen order. Distributor. 2. Explain where and how to make shipment.
Page 58: Handle Covers
ECLIPSE Serial No. All 1.1 Handle Covers DRY ERASE MARKER ONLY 4265170 ® 4265171 4265172...
Page 59 REFERENCE SW2, See 19.1 4131618 • Key • Nut, Face 4130132 Switch, Rocker REFERENCE SW1, See 19.1 4253330 Cover, Upper Console 4260810 Decal, Eclipse 2 4265172 Decal, Key Switch 4265171 Decal, Reel 4265170 Decal, Parking Brake 402056 Screw, #8-32 x 3/8” Slotted 4253310...
Page 60: Handle Assembly
ECLIPSE Serial No. All 2.1 Handle Assembly...
Page 61 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 4256578 Handle 4136328 Plate, Tilt 434029 Screw, 1/4-20 x 1” Hex Socket 453023 Flat Washer, 1/4 446130 Lockwasher, 1/4 Heavy 443102 Nut, 1/4-20 Hex 4136325 Bail 4147696 Handle, Overmolded Includes Decal 4260432 Hand Throttle Potentiometer REFERENCE R1, See 19.1 454020...
Page 62: Handle To Frame Mount
ECLIPSE Serial No. All 3.1 Handle to Frame Mount Eclipse 118 and 118F 63334 63343 63335 63344 63336 63345 63337 63346 Eclipse 122, 122F, and 126 Handle Assembly 63338 63347 63339 63348 63340 63349 63341 63350 63342 63351...
Page 63 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 2811559 Bolt, Handle Mount 447224 Lockwasher, 5/8 Internal Tooth 443828 Nut, 5/8-18 Hex Jam 4257813 Handle Stop, Right Side 4257814 Handle Stop, Left Side Eclipse 118, 118F Left Side 2809900 Torsion Spring, Handle Eclipse 122, 122F, 126 Right Side 2809900...
Page 64: Power Module Mounting Plate
ECLIPSE Serial No. All 4.1 Power Module Mounting Plate Gen-Set Battery 19 20 4172240 Fixed Head Frame Shown. Floating Head Similar...
Page 65 Screw, 1/2-13 x 1-3/4” Hex Head 344132 Washer, 1/2 443118 Nut, 1/2-13 Hex 444758 Locknut, 1/2-13 Hex Center 364164 Spring, Extension 400404 Screw, 1/2-13 x 1” Hex Head 4264210 Decal, Jacobsen 306998 Lockwasher, #10 Int/Ext Tooth > Change from previous revision...
Page 66: Frame
ECLIPSE Serial No. All 5.1 Frame Eclipse 118, 122 and 126 63334 63343 63335 63344 63338 63347 63339 63348 63342 63351 ® A Textron Company CHARLOTTE, NC MADE IN U.S.A. YEAR OF PRODUCTION: Manufactured under one or more of the following U.S. patents: xxxxxxx xxxxxxx xxxxxxx xxxxxxx xxxxxxx xxxxxxx Eclipse...
Page 67 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes Eclipse 118, 122, and 126 4253156 Frame, L.H. Side Fixed Head Eclipse 118F and 122F 4253154 Frame, L.H. Side Floating Head Eclipse 118, 122, and 126 4253155 Frame, R.H. Side Fixed Head Eclipse 118F and 122F 4253157...
Page 68: Lower Unit
ECLIPSE Serial No. 63334 - All Serial No. 63342 - All Serial No. 63348 - All 6.1 Lower Unit Serial No. 63335 - All Serial No. 63343 - All Serial No. 63351 - All Serial No. 63338 - All Serial No. 63344 - All Fixed Head Units Serial No.
Page 69 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes Reel and Bedknife Assembly See 7.1 400264 Screw, 3/8-16 x 1-1/4” Hex Head 446142 Lockwasher, 3/8 Heavy 400258 Screw, 3/8-16 x 3/4” Hex Head 3001610 Block, Bedknife Adjuster 366726 Bolt, 5/8-11 Special 366653 Spacer, 7/8 x 3/8 x 1/8”...
Page 70: Reel
ECLIPSE Serial No. 63334 - All Serial No. 63342 - All Serial No. 63348 - All 7.1 Reel Serial No. 63335 - All Serial No. 63343 - All Serial No. 63351 - All Serial No. 63338 - All Serial No. 63344 - All Fixed Head Units Serial No.
Page 71 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes See Chart Reel 4105281 Bearing Housing 366650 • Grease Seal 545940 • Bushing 500534 • Bearing Cup and Cone 4179720 Bearing Housing 366650 • Seal 545940 • Bushing 500534 • Bearing Cup and Cone 4128725 •...
Page 72: Grass Shield And Roller Brackets
ECLIPSE Serial No. 63334 - All Serial No. 63342 - All Serial No. 63348 - All 8.1 Grass Shield and Roller Brackets Serial No. 63335 - All Serial No. 63343 - All Serial No. 63351 - All Serial No. 63338 - All Serial No.
Page 73 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes Used on 63334, 63343, 63335, and Grass Shield, 18 Inch 4139661 63344 Used on 63338, 63347, 63339, and 4139660 Grass Shield, 22 Inch 63348 4139662 Grass Shield, 26 Inch Used on 63342 and 63351 4127335 •...
Page 74: Floating Head Reel Connection
ECLIPSE Serial No. 63336 - All Serial No. 63345 - All 9.1 Floating Head Reel Connection Serial No. 63337 - All Serial No. 63346 - All Serial No. 63340 - All Serial No. 63349 - All Floating Head Units Only Serial No.
Page 75 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 4175221 Rear Roller - 18” Used on 63336, 63345, 63337, 63346 1004990 Rear Roller - 22” Used on 63340, 63349, 63341, 63350 4175220 • Shaft, 18” Used on 63336, 63345, 63337, 63346 3010422 •...
Page 76: Outer Reel Assembly
ECLIPSE Serial No. 63336 - All Serial No. 63345 - All 10.1 Outer Reel Assembly Serial No. 63337 - All Serial No. 63346 - All Serial No. 63340 - All Serial No. 63349 - All Floating Head Units Only Serial No. 63341 - All Serial No.
Page 77 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes Used on 63336, 63345, 63337, and 4175221 Rear Roller, 18” 63346 Used on 63340, 63349, 63341, and 1004990 Rear Roller, 22” 63350 Used on 63336, 63345, 63337, and 4175220 • Shaft, 18” Roller 63346 Used on 63340, 63349, 63341, and 3010422...
Page 78: Inner Reel Assembly
ECLIPSE Serial No. 63336 - All Serial No. 63345 - All 11.1 Inner Reel Assembly Serial No. 63337 - All Serial No. 63346 - All Serial No. 63340 - All Serial No. 63349 - All Floating Head Units Only Serial No. 63341 - All Serial No.
Page 79 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes Used on 63336, 63345, 63337, and 4170204 Frame, 18” Reel 63346 Used on 63340, 63349, 63341, and 5002577 Frame, 22” Reel 63350 400192 Screw, 5/16-18 x 1-1/2” Hex Head 446142 Lockwasher, 3/8 Heavy 4225504 15 Blade, 18”...
Page 80: Differential And Rollers
ECLIPSE Serial No. All 12.1 Differential and Rollers...
Page 81 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 1000024 18” Smooth Roller 132655 22” Smooth Roller 1000027 26” Dimpled Roller 366699 • Differential Gear Bushing 366698 • Drum Bushing 366701 • Grease Seal 366700 • Grease Seal 241836 • Differential Gear 319085 •...
Page 82: Parking Brake And Wheels
ECLIPSE Serial No. All 13.1 Parking Brake and Wheels...
Page 83 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 1000476 R.H. Hub 338766 • Bearing 366705 • Grease Seal 164056 Brake Band 132663 Brake Mounting Bracket 132658 Seal Housing 365753 • Grease Seal 4128725 • Grease Fitting 164063 Brake Mounting Bracket 1000477 L.H.
Page 84: Belts And Drive Motors
ECLIPSE Serial No. All 14.1 Belts and Drive Motors Fixed Head Frame Shown. Floating Head Similar...
Page 85 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 446116 Lockwasher, #10 2000148 Bracket, Bearing 2811070 Belt, Polychain, 80 Tooth 2811223 Pully, 18 Tooth 2811107 Pully, 112 Tooth 3001273 Shaft 4140154 Floating Head Pulley Cover 4199640 Cover, Belt 2811106 Belt, 130 Tooth 2811108 Pulley, 23 Tooth 4256571...
Page 86: Harness Routing
ECLIPSE Serial No. All 15.1 Harness Routing SW1Reel Switch F230 Amp Fuse SW2 Ignition J14 CAN Diagnostic Connector Switch R1 Hand Throttle Potentiometer R2 Rotary Switch J1 and J2 Controller J6 and J7 Connection Reel Motor Controller J8 and J9 J10 and J11 Connection Traction Motor...
Page 87 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 4254330 Harness, Main 4262910 • 30 Amp Mini Fuse REFERENCE F1, See 19.1 4253190 Controller, Reel Motor REFERENCE U1, See 19.1, 4.1 4261770 Motor, Brushless Bi-Directional REFERENCE M1, See 19.1, 6.1, 9.1 4253190 Controller, Traction Motor REFERENCE U2, See 19.1, 4.1...
Page 88: Genset Power Source
ECLIPSE Serial No. 63334 - All Serial No. 63337 - All Serial No. 63341 - All 16.1 Genset Power Source Serial No. 63335 - All Serial No. 63338 - All Serial No. 63336 - All Serial No. 63339 - All 63305 Serial No.
Page 89 Screw, 5/16-24 x 7/8” Hex Socket 446136 Lockwasher, 5/16 Heavy 450697 Screw, M5-.8 x 16 mm Hex Socket 450409 Lockwasher, M5 800646 Screw, 5/16-24 x 1-1/4” Hex Socket 4182386 Decal, Jacobsen 450700 Screw, M5-.5 x 30 mm Hex Socket > Change from previous revision...
Page 90: Battery Power Source
ECLIPSE Serial No. 63343 - All Serial No. 63347 - All Serial No. 63341 - All 17.1 Battery Power Source Serial No. 63344 - All Serial No. 63348 - All Serial No. 63345 - All Serial No. 63349 - All 63306 Serial No.
Page 91 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 2809837 Spring, Extension 444708 Locknut, 1/4-20 Center 443102 Nut, 1/4-20 Hex 446130 Lockwasher, 1/4 Heavy 441604 Carriage Bolt, 1/4-20 x 1” 400108 Screw, 1/4-20 x 3/4 Hex Head 443106 Nut, 5/16-18 Hex 446136 Lockwasher, 5/16 Heavy 452006...
Page 92: Battery Case
ECLIPSE Serial No. All 18.1 Battery Case To Battery Gauge STOP 4170001 Battery Post Style Terminal Hardware See Above Battery and Battery Monitor Connections...
Page 93 ECLIPSE Item Part No. Qty. Description Serial Numbers/Notes 68668 Battery Case Does Not Include Batteries 4105660 • Screw, 5/16-18 x 1-1/4” Nylon 452004 • Flat, Washer 1/4 4105800 • Fuse, 50A Reference F1, See 19.1 447214 • Lockwasher, 5/16 Internal 443106 •...
Page 94: Electrical Schematic
ECLIPSE Serial No. All 19.1 Electrical Schematic Battery Pack (Battery) Engine Control J23- + (Hybrid Genset) J23- – Battery Gauge Ignition Coil Spark Plug Engine Red/Yel Red/Yel J23- + On/Off J23- – Switch Generator Generator (Hybrid Genset) Red/Blu Red/Wht Start J1-2 +48V Traction Motor J1-1...
Page 95 ECLIPSE Optional Work Light Light Switch Work Light J15-1 J15-2 J9-1 J12-1 +48V Input Phase A Phase A J9-2 J12-2 Phase B Phase B J12-3 Phase C Phase C Gn/Ye J12-4 Gn/Ye Traction Shield Shield Motor Traction Controller Motor J8-1 Motor Motor Tach Case...
Page 96 Illustration Number See 18.1 12 Volt SLA Battery Obtain batteries localy or See 18.1 12 Volt SLA Battery through your Jacobsen Dealer See 18.1 12 Volt SLA Battery Battery Power Module Only See 18.1 12 Volt SLA Battery Not Shown...
Page 97 * Refer to the Operator’s manual or the Parts & Maintenance Manual for the correct hydraulic oil requirements for your machine. Jacobsen offers a High Usage Parts Catalog illustrating commonly used Parts through easy to read line Drawings. See your local Jacobsen Dealer for a copy.
Page 98 INDEX 1000024.......81 304745....71 367164 ....69 4131369 ....71 1000027.......81 306998......65 367512 ......69 4131370 ....71 1000476.......83 308028......81 367554 ......85 4131371 ...... 79 1000477.......83 308030......81 395367 ......81 4131373 ...... 79 1000480.......79 315298......79 395418 ......81 4131618 ...... 59 1002224.......77 319085......81 395419 ......
Page 99 INDEX 4203300...... 75 4265710 ...... 65 450409 ......89 4208861...... 96 4273518 ...... 67 450419 ......93 4223946...... 71 4324900 ...... 71 450697 ......89 422504......61 434003 ......81 450700 ......89 4225502...... 71 434011 ......85 452004 ....59 4225504......
Page 100 Equipment from Jacobsen is built to exacting standards ensured by ISO 9001 and ISO 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by Genuine Jacobsen Parts provide reliable, high-quality product support.

Jacobsen Eclipse 2 Technical Manual

Table of Contents

1 Safety

2 Specifications

3 Decals

4 Controls

5 Operation

6 Adjustments (All Units)

7 Fixed Head Reel Adjustments

8 Floating Head Reel Adjustments

9 Battery Power Module

10 Gen-Set Power Module

11 Maintenance

12 Troubleshooting

13 Maintenance & Lubrication Charts

Parts Catalog 14

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Jacobsen Eclipse 2

Summary of Contents for Jacobsen Eclipse 2

This manual is also suitable for:

Table of Contents