Ford 2001 Mercury Cougar Owner's Manual

page of 298

/ 298
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

www.carburetor-manual.com

Would you like some Free Manuals?

http://carburetor-manual.com/free-shop-manual-club-t-13.html

Also visit

http://freeshopmanual.com

for more Free Manuals

Also Visit my website for 7 FREE Download Manuals starting

with this one.

"The ABC's of Carburetion"

Click Here Now

file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

Table of Contents

Summary of Contents for Ford 2001 Mercury Cougar

Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 Ford Motor Company. Ford may change the contents without notice and without incurring obligation. Copyright E 2000 Ford Motor Company...
Page 3: Introduction
Introduction CALIFORNIA Propositon 65 Warning Warning: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of...
Page 4 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 5 Introduction Vehicle symbol glossary These are some of the symbols you may have on your vehicle. Safety Alert See Owner's Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti Lock Brake System Brake Fluid -...
Page 6 Introduction Vehicle symbol glossary Child Safety Door Panic Alarm Lock/Unlock Engine Oil Engine Coolant Engine Coolant Do Not Open When Hot Temperature Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Emission System Level Engine Air Filter...
Page 7 Instrumentation Page 24, 25 Page 87 Page 86 Headlamp control/ Turn signal/ Hazard flasher Foglamp control* high beams control Page 25 Page 8 Page 88 Panel dimmer Instrument Windshield wiper/ control cluster washer control Page 206 Page 128 Page 85 Hood release Air bag system Ignition switch...
Page 8 Instrumentation Page 26 On various models the appearance Trip computer and location of some items may differ from those shown here. Page 106 However, the page references Anti theft system given still apply. status indicator Page 12 Traction control system * Page 28 Rear window defroster control Page 29...
Page 9: Instrumentation
Instrumentation INSTRUMENT CLUSTER LIGHTS AND CHIMES Check engine Your vehicle is equipped with a computer that monitors the engine's emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 10 Instrumentation The check engine" indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine's emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Page 11 Instrumentation If the check engine" light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Page 12: Controls And Features
Instrumentation Air bag readiness Briefly illuminates when the ignition is turned on. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Foglamps Illuminates when foglamps are switched on. Refer to Foglamp control in the Controls and features chapter for notes on use.
Page 13: Seating And Safety Restraints
Instrumentation High beams Illuminates when the headlamp high beams are on. Traction control system (if equipped) Illuminates to indicate the system is functioning to regulate tire traction. The control will toggle this feature on or off, but the feature defaults to on after each cycle of the ignition key.
Page 14 Instrumentation Charging system Illuminates when the ignition is turned on and the engine is off. The light also illuminates when the battery is not charging properly and the vehicle may require electrical system service. Engine oil pressure Illuminates when the ignition is turned on and the engine is off.
Page 15 Instrumentation Low coolant (if equipped) Briefly illuminates when the ignition is turned on and the engine is off. Illuminates when the engine coolant level is low. If a valid signal is received, the light will remain on until the ignition is cycled. Refer to the Maintenance and care chapter to check the engine coolant level.
Page 16: Driving
Instrumentation O/D off indicator (automatic transaxle only) Illuminates and remains illuminated when the transaxle control switch on the end of the gearshift lever is pressed and overdrive is turned off. Indicates the status of the transaxle and will flash steadily if a malfunction is detected.
Page 17 Instrumentation Testing the warning and indicator lights Turn the ignition key to the on position without starting the engine. The following warning and indicator lights should illuminate: charging system, safety belt (does not illuminate, if the driver's safety belt is fastened), low coolant, engine oil pressure, check engine, air bag readiness, traction control, brake system and ABS.
Page 18 Instrumentation Headlamps on warning chime Sounds when the headlamps are on, the ignition is off (and the key is not in the ignition) and the driver's door is open. Key-in-ignition warning chime Sounds when the key is left in the off/lock or accessory position and the driver's door is open.
Page 19 Instrumentation INSTRUMENT CLUSTER GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area. If it enters the red section, the engine is overheating. Stop the vehicle, turn off the engine and let the engine cool.
Page 20 Instrumentation Tachometer Indicates the engine speed in revolutions per minute (rpm). Trip odometer Registers the distance traveled on individual journeys. Refer to Trip computer in the Controls and features chapter. Speedometer Speedometer Indicates the current vehicle speed. On Cougar S vehicles, the speedometer registers up to 160 mph.
Page 21 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 22 Routine service should be performed by an authorized Ford or Lincoln/Mercury Dealer. The light should be switched off by your Ford or Lincoln/Mercury Dealer after completing the service. To reset the light, hold the SELECT and UNITS buttons on the trip computer for 5 seconds.
Page 23 Instrumentation Frost warning Illuminates when ambient air temperatures are between 0ºC (32ºF) and 4ºC (39ºF). The yellow sign warns of possible ice on the roads. Danger of ice warning Illuminates when 0ºC (32ºF) and below. The red sign warns of an increased danger of icy roads.
Page 24 Instrumentation Washer fluid warning Indicates that the washer fluid reservoir is low. Refill as soon as possible. If a valid signal is received, the light will remain on until the ignition is cycled. Door ajar Illuminates when the ignition is switched on and any door or liftgate is open.
Page 25: Controls And Features
Controls and features INSTRUMENT PANEL CONTROLS Headlamp control Lamps off. Turn one position clockwise: Parking lamps, instrument panel lamps, license plate lamps and tail lamps on. Turn two positions clockwise: Headlamps on.
Page 26 Controls and features Foglamp control (if equipped) Pull the control toward you while the headlamps are on to turn the foglamps on. Push the control in to turn off the foglamps. Daytime running lights (DRL) (Canadian vehicles only) The DRL system turns the headlamps on, with a reduced light output, when: •...
Page 27 Controls and features Trip computer Press the SELECT button to change between temperature, average speed, tripmeter, distance to empty or fuel consumption. Press the UNITS button to toggle between English or Metric units. Press the RESET button to set the function to zero (if resetable).
Page 28 Controls and features Tripmeter Shows how far you have traveled since last reset. Distance to empty Shows the approximate distance you can drive with the fuel remaining in the tank. Average fuel economy Shows the average fuel economy since last reset. Digital clock Switch the ignition on: The clock can be set to either 12 or 24 hour...
Page 29 Controls and features Traction control system (if equipped) This system helps prevent wheel spin to improve tire traction. The control will toggle this feature on or off, but the feature defaults to on after each cycle of the ignition key. The light in the control illuminates when the system is switched off.
Page 30 Controls and features Climate controls Your vehicle is equipped with a manual heating and air conditioning system. Vents Adjust as necessary. Low airflow: rotate vent clockwise. High airflow: rotate vent counterclockwise.
Page 31 Controls and features Temperature Controls the temperature of the airflow inside the vehicle. Fan speed Controls the volume of air circulated in the vehicle. Mode selector Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor (if equipped) will operate in all modes except .
Page 32 Controls and features • MAX A/C (if equipped): Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers.
Page 33 Controls and features • : Distributes outside air through the instrument panel registers and the floor ducts. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Page 34 Controls and features • : Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield when temperature is set to full hot and fan speed is set to 4. If the temperature is about 4°C (39°F) or higher, the air conditioner (if equipped) will automatically...
Page 35 Controls and features • Don't put objects under the front seat that will interfere with airflow to the back seats. • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood).
Page 36 Controls and features AUDIO SYSTEM Anti-theft protection panel (if equipped) To deter would be thieves, Ford audio units have a removable front panel without which the unit will not work. Avoid touching the contacts on the back of the panel and do not use excessive force to refit it.
Page 37 Radio reception To gain the best reception, always tune to the strongest station signal available. The following tips will help you gain the best reception from your Ford audio system. AM reception Under most conditions, strong signals provide stable sound quality and little signal disturbance.
Page 38 Controls and features PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD Volume/power control Press for on/off. This button can also operate the unit for up to one hour with the ignition turned off. The radio automatically switches off after one hour. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control.
Page 39 Controls and features AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode Tis control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 40 Controls and features Tune adjust Tune adjust in radio mode • Press A to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. •...
Page 41 Controls and features Seek function The seek function control works in radio, tape or CD mode. Seek function radio mode Press A to find the next listenable station down the frequency band. Press " to find the next listenable station up the frequency band. Seek function in tape mode Press A to listen to the previous selection on the tape.
Page 42 Controls and features Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode Press A to find the next listenable station down the frequency band. Press " to find the next listenable station up the frequency band.
Page 43 Controls and features Scan function The scan function works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode.
Page 44 Controls and features Scan function The scan function works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode.
Page 45 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you...
Page 46 Controls and features These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner of your original presets. To deactivate autoset and return to your audio system's maually set memory stations, press the AUTO control again.
Page 47 Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • A to shift the sound to the front • " to shift the sound to the rear. Tape/CD select •...
Page 48 Controls and features Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track.
Page 49 Controls and features Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the noise reduction. Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby" and the double D symbol trademarks of Dolby Laboratories Licensing Corporation.
Page 50 Controls and features Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Mute button Press the control to mute the playing media.
Page 51 Controls and features The AM/FM stereo/cassette with premium sound is compatible with a CD changer. Automatic Fade/Balance CD control Waveband/ music search control AutoStore selector Bass/ Scan Tape Treble tuning control control buttons Station preset On/Off and SEEK buttons Volume tuning MENU control...
Page 52 Controls and features The AM/FM stereo/single CD player with premium sound is compatible with a CD changer. CD eject Fade/Balance CD control Waveband/ control AutoStore selector Scan Bass/Treble Clock tuning control Station preset On/Off and SEEK buttons Volume tuning MENU control control button...
Page 53 Controls and features On/off Press for on/off. This button can also operate the unit for up to one hour with the ignition turned off. The radio automatically switches off after one hour. Volume control The display indicates the level selected. Bass/Treble control Press BASS/TREBLE"...
Page 54 Controls and features Fade/Balance control Press FADE/BAL" once for fade (front to rear) or twice for balance (left to right), and use the volume control for sound system adjustment. The display indicates the level selected. The fade function is applicable to vehicles with front and rear speakers only.
Page 55 Controls and features Band selector (AM/FM) • Press repeatedly during radio reception to select AM, FM1, FM2 or AutoStore (see AutoStore selector). The display indicates the selection made. • Press during tape or CD playback to return to radio reception. AutoStore selector AutoStore selects six strong FM station signals and stores them on...
Page 56 Controls and features Station preset buttons Select a waveband (FM or AM) and tune to the station required. Press and hold one of the preset buttons. When sound returns, the station has been stored. 24 preset frequencies can be stored - six on each of the AM, FM1, FM2 and AutoStore bands.
Page 57 Controls and features Automatic Volume Control (AVC) Press the MENU button repeatedly until a display like the one shown opposite appears. Then use the SEEK button to turn this function on (AVC + 1" to AVC + 7") or off (AVC OFF").
Page 58 Controls and features Fast forward/rewind • Press button fully in for fast forward. • Press and release button to end fast forward and restart the tape. • Press button fully in for rewind. • Press and release button to end rewind and restart the tape. If the beginning of the tape is reached, press both buttons part way in to restart...
Page 59 Controls and features Tape side selection During tape playback, press both buttons partially in to change the tape side being played. Tape eject Press both buttons fully in to eject the cassette and restore radio reception. To pause tape playback Press AM/FM to pause tape playback and restore radio reception, or the CD button for CD...
Page 60 Controls and features Automatic Music Search (AMS) Press AMS to turn this function on or off. With this feature activated, press either A or " buttons (as appropriate), to obtain the previous or next track on the tape. Cassette care and maintenance For best possible sound quality, use tape cassettes that are clean and in good condition.
Page 61 Controls and features MENU button (main features) – tape Use the MENU button to access main menu features, and the SEEK button for adjustment. Dolby Br noise reduction Press the MENU button repeatedly until a display like the one shown opposite appears.
Page 62 Controls and features AM/FM stereo/single CD player with premium sound CD Playback (8cm and 12cm CDs can be played) CD playback starts and radio reception is interrupted, when a CD is inserted into the entry slot. PLAY CD" appears in the display. Press CD to start playback from a CD already in the audio unit.
Page 63 Controls and features Fast forward/reverse Press and hold SEEK or SEEK " to search backwards or forwards across the tracks on the disc. Scan mode Press the SCAN button. Each track is played in turn for a short period. During this scan, SCAN" appears in the display.
Page 64 Controls and features CD care and maintenance For best possible sound quality, use CDs that are clean and in good condition. CD error codes Codes may be shown in the audio unit display that indicate errors with the CD unit. These codes are as follows: Display Description/rectification...
Page 65 Controls and features Random track playback (SHUF) Press the MENU button repeatedly until a display like the one shown opposite appears. Then use the SEEK button to turn this function on (SHUF ON") or off (SHUF OFF"). With the function on, the elapsed time indicator is replaced by SHUF"...
Page 66 Controls and features Automatic Volume Control Press the MENU button repeatedly until a display like the one shown opposite appears. Then use the SEEK button to turn this function on (AVC + 1" to AVC + 7") or off (AVC OFF"). •...
Page 67 Controls and features Random track playback (SHUF) Cassette and CD radio units Press the MENU button repeatedly until a display like the one shown opposite appears. Then use the SEEK button to turn this function on (SHUF ON") or off (SHUF OFF").
Page 68 Controls and features Automatic Volume Control (AVC) Cassette and CD radio units Press the MENU button repeatedly until a display like the one shown opposite appears. Then use the SEEK button to turn this function on (AVC ON") or off (AVC OFF"). •...
Page 69 Controls and features PREMIUM AM/FM STEREO IN DASH SIX CD RADIO Volume/power control Press the control to turn the audio system on or off. Push on Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal"...
Page 70 Controls and features AM/FM select The AM/FM select control works in radio and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 71 Controls and features Tune adjust for CD mode • Press A to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.
Page 72 Controls and features Seek function in CD mode • Press A to seek to the previous track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing.
Page 73 Controls and features Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 74 Controls and features Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control.
Page 75 Controls and features CD select CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
Page 76 Controls and features Load The load feature allows you to load single CDs into the player internal to the radio. This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the door has been opened by the player.
Page 77 Controls and features Auto load This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio. Press and hold the LOAD control until AUTOLOAD # is displayed. The CD door will open. Load the desired disc, one at a time.
Page 78 Controls and features Auto eject Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD.
Page 79 Controls and features Shuffle feature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode. When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK. SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system.
Page 80 Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system's treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Page 81 Controls and features Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available.
Page 82 Controls and features When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF. SELECT HOURS, SELECT MINUTES Allows you to adjust the hours and minutes. Refer to Setting the clock. TRAFFIC ON/OFF Traffic announcements can be programmed as local or distant.
Page 83 Controls and features RDS features: Once the RDS feature is on, press the RDS control to scroll through the following selections: Traffic announcements This feature allows you to hear traffic announcements while in CD mode. These announcements are broadcast by traffic capable RDS stations.
Page 84 Controls and features Program type This feature allows you to search for RDS stations selectively by their program type. Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections:...
Page 85 Controls and features Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display). RDS clock feature Refer to Setting the clock for information.
Page 86 Controls and features STEERING COLUMN CONTROLS Ignition 1. Ignition off, steering wheel locked. On vehicles with automatic transaxles, the ignition key can return to this position only if the gearshift lever is in P (Park). 2. The accessory position. Steering unlocked, radio operational.
Page 87 Controls and features 3. Ignition switched on, all electrical circuits operational. Warning and indicator lights illuminate. This key position is for normal driving. 4. Starter motor activated. Release the key as soon as the engine starts. Tilt steering Pull the locking lever on the steering column cover up to adjust the steering column position.
Page 88 Controls and features Multi-function switch The turn signal functions are available only with the ignition switch on. Right turn signal Move the lever up. Left turn signal Move the lever down.
Page 89 Controls and features Flash-to-pass Pull the lever toward you and release quickly for flash to pass" operation. High beam headlamps Push the lever toward the instrument panel. Windshield wipers and washer Wipers Lift the windshield wiper lever to the desired speed interval. •...
Page 90 Controls and features Intermittent wiper control Rotate the variable intermittent wiper control to the desired speed. 1 = Short time interval 6 = Extended time interval Washer Pull the lever toward the steering wheel. The washer operates in conjunction with the windshield wipers.
Page 91 Controls and features Speed control (if equipped) Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control on • Press On. Vehicle speed cannot be controlled until the vehicle is travelling at or above 48 km/h (30 mph).
Page 92 Controls and features To turn speed control off Press Off. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press + and release. For speed control to operate, the speed control must be on and the vehicle speed must be greater than 48 km/h (30 mph).
Page 93 Controls and features To set a higher speed • Press and hold +. Release when the desired set speed is reached, or • press and release +. Each press will increase the set speed by 1.6 km/h (1 mph) or •...
Page 94 Controls and features To disengage speed control • Lightly depress the brake or clutch pedal. Disengaging the speed control will not erase the previously programmed set speed. To return to a set speed • Press =. For = to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 95 Controls and features Reading lamps (if equipped) The reading lamps are operated by separate on/off switches and can be adjusted to point in the desired direction. On Off 12 SEC Sunroof (if equipped) The electric sunroof can be Open/Lift operated only when the ignition is switched on.
Page 96 Controls and features DOOR MOUNTED CONTROLS Power mirrors The control can be swiveled and turned. Turn the control clockwise to adjust the driver's side mirror, counterclockwise to adjust the passenger side mirror. Adjust the selected mirror by moving the center control in the desired direction.
Page 97 Controls and features Power windows The windows will only operate when the ignition is switched on. Press the appropriate control to operate the power windows at each door position. Both windows can be controlled from the control on the driver's door. The passenger's door window can be operated individually with a separate door control.
Page 98: Roadside Emergencies
Controls and features Positive retention floor mat (Driver’s side only) Position the floor mat in the footwell. Place the mat eyelet over the pointed end of the retention post from the rear and rotate forward to install. Adjust the floor mat position to allow proper operation of accelerator pedal, brake pedal and clutch pedal (if...
Page 99 Controls and features LUGGAGE COMPARTMENT The luggage compartment lock has one locking position. Remote luggage compartment control Push the control located under the instrument panel by the driver's door to open the luggage compartment. To open the luggage compartment at least one door must be unlocked. Interior luggage compartment release Your vehicle is equipped with a...
Page 100 Controls and features To open the luggage compartment door (lid) from the inside, pull the illuminated T" shaped handle and push open the door (lid). The material that the handle is made of will glow in the darkness of the luggage compartment following brief exposure to ambient light.
Page 101 Controls and features On hot days, the temperature in the trunk can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat related injuries, including brain damage. Small children are particulary at risk.
Page 102 Controls and features Cargo cover Do not place objects on the cargo cover. Removing the cargo cover First, detach the lifting straps on the liftgate. Then pull it out horizontally without tilting it. Replacing the cargo cover Insert the cover horizontally, align it and push in as far as the stop.
Page 103 Controls and features REMOTE KEYLESS ENTRY SYSTEM (if equipped) If your vehicle has a remote entry system, you can lock and unlock the vehicle doors and open the luggage compartment without using a key. The remote also has a panic alarm feature.
Page 104 Controls and features Opening the luggage compartment Press the control. Sounding the panic alarm Press the control. The horn will sound and the direction indicators will flash for approximately two minutes. To deactivate the alarm, press the control again or turn the ignition key to the on position.
Page 105 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter. Do not take the front part of the transmitter apart. 2. Remove the old battery. 3. Place the positive (+) side of the new battery down.
Page 106 Controls and features ANTI-THEFT ALARM SYSTEM (if equipped) The system is available with Remote Keyless Entry. The system acts as a deterrent against unauthorized persons opening the doors, luggage compartment or hood. Activation The system is activated by pressing control once. The ignition key must be removed from the ignition and the doors, hood and liftgate fully closed, to allow activation.
Page 107 Controls and features PASSIVE ANTI-THEFT SYSTEM The Passive Anti Theft System (PATS) is an engine immobilization system. It is an additional theft protection feature which prevents the engine from being started unless a coded key is used. Automatic arming The system is armed five seconds after switching off the ignition.
Page 108 Controls and features Functional check When the ignition is switched on, the control light will illuminate for approximately three seconds to indicate that the system is operating correctly. If the control light flashes rapidly for approximately one minute and then repeatedly at irregular intervals, the system did not recognize the key code.
Page 109 Controls and features Key coding A maximum of 7 keys in all can be coded with any two coded keys. • Insert the first key in the ignition switch and turn to position 3. • Turn the key back to position 1 and remove from the ignition switch within 5 seconds.
Page 110: Seating And Safety Restraints
Seating and safety restraints HEAD RESTRAINTS Adjusting the head restraints If your vehicle is equipped with adjustable head restraints, push or pull the head restraint to raise it to the desired height. To lower, push the small catch in the collar around the stem and raise or lower the head restraint to the desired height.
Page 111 Seating and safety restraints Pull the lever on the outside of the seat to recline the seat. Pull the lever on the outside of the seatback to lean the seatback forward. Fold back the seatback until it locks with a distinct `click' and slide the seat backwards until it locks in position.
Page 112 Seating and safety restraints Power height adjustment (if equipped) The controls are located on the left front corner of the seat. Adjusting the power seats (if equipped) The controls are located on the left front corner of the seat. Move the relevant control in the respective direction to adjust the seat, seatback and lumbar as follows:...
Page 113 Seating and safety restraints Closing the liftgate To avoid injury to rear seat occupants when closing the liftgate, ensure that the head of any rear seat occupant is not in the path of the closing liftgate. Request that the occupants, especially taller occupants, lean forward and under the roof structure to avoid making contact...
Page 114 Seating and safety restraints SAFETY RESTRAINTS Important safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained.
Page 115 Seating and safety restraints Never let a passenger hold After any vehicle collision, a child on his or her lap the seat belt system at all while the vehicle is moving. The outboard seating positions passenger cannot protect the (except driver, which has no child from injury in a collision.
Page 116 Seating and safety restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly Tell Tale Label" (if applicable, located on lap portion at outboard side of seat above anchorage point) is activated and states that the retractor assembly is required to be replaced, or the seat belt assembly automatic locking retractor"...
Page 117 Seating and safety restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1. Use the shoulder belt on the outside shoulder only.
Page 118 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically prelocked. The belt will still react to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver's safety belt. When to use the automatic locking mode •...
Page 119 Seating and safety restraints Canceling automatic locking mode Unfasten the combination lap and shoulder belt and allow it to completely retract. This will cancel the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Front seat safety belt height adjustment Position the shoulder belt height adjusters so that the...
Page 120 Seating and safety restraints Safety belt warning light and warning chime Illuminates in the instrument cluster and a chime sounds to remind the driver to fasten his or her safety belt. Conditions of operation If... Then... If the driver's safety belt is not The safety belt warning light buckled before the ignition key is illuminates for one to two minutes...
Page 121 Seating and safety restraints Belt Minder The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver's safety belt is unbuckled by intermittently sounding a chime and illuminating the Safety belt warning light in the instrument cluster once the vehicle speed has exceeded 5 km/h...
Page 122 I'm not going far" 3 of 4 fatal crashes occur within 25 miles of home. Belts are uncomfortable" Ford designs its safety belts to enhance comfort. If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 123 Seating and safety restraints Reasons given... Consider... Belts wrinkle my clothes" Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. The people I'm with don't wear Set the example, teen deaths occur belts"...
Page 124 Seating and safety restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 125 Seating and safety restraints • the driver's safety belt is unbuckled. • the parklamps/headlamps are in OFF position. To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the ON position (DO NOT START THE ENGINE).
Page 126 Seating and safety restraints 6. Within seven seconds of the Safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
Page 127 Seating and safety restraints Safety belt extension assembly The safety belt may be too short even when fully extended. Approximately 20 cm (8 inches) may be added to the length of the belt with a safety belt extension (part number 611C22). Safety belt extensions are available at no cost from your dealer.
Page 128 Seating and safety restraints Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. If the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 129 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is the greatest close to the trim covering and the...
Page 130 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer.
Page 131 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions then in the front seating positions.
Page 132 Seating and safety restraints How does the front air bag system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the...
Page 133 Seating and safety restraints While the system is designed to help reduce serious injuries, it may also cause abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly...
Page 134 Seating and safety restraints The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Page 135 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Page 136 Seating and safety restraints How does the side air bag system work? (if equipped) Side air bags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side air bags are fitted on the outboard side of the seatbacks of the front seats.
Page 137 Seating and safety restraints If the air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 138 Seating and safety restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter. Routine maintenance of the air bag is not required.
Page 139 Seating and safety restraints CHILDREN AND SAFETY RESTRAINTS Rear-facing child seats or infant carriers should never be placed in the front seats. To reduce the risk of injury, make sure children sit where they can be properly restrained. Always transport children 12 years old and under in the back seat and always use appropriate child restraints.
Page 140 Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Page 141 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt positioning booster seat that is labelled as conforming to all federal motor vehicle safety standards.
Page 142 Seating and safety restraints SAFETY SEATS FOR CHILDREN Rear facing child seats or infant carriers should never be placed in the front seats. Carefully follow all of the manufacturer's instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 143 • Put the safety belt in the automatic locking mode. Refer to Using automatic locking mode in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 144 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Ford recommends that you properly secure children in the rear seat whenever possible. If you must use a forward facing child seat in the front seat, move...
Page 145 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage.
Page 146 Seating and safety restraints 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
Page 147 Seating and safety restraints Attaching child safety seats with tether straps Some child seat manufacturers make safety seats that include a tether strap which goes over the back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory.
Page 148 Seating and safety restraints 1. Position the child safety seat on the rear passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with moveable head restraints, route the tether strap under the head restraint and between the head restraint posts if you can.
Page 149 Seating and safety restraints 6. Tighten the child safety seat tether strap according to the manufacturer's instructions. 7. Once you have installed the safety seat, assure that the tether strap is fastened securely. Also, test the safety seat before you place the child in it.
Page 150 Starting IMPORTANT SAFETY PRECAUTIONS A computer system controls the engine's idle revolutions per minute (rpm). When the engine starts, the idle rpm runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your dealer or a qualified service technician.
Page 151 Starting Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. IMPORTANT VENTILATION INFORMATION If the engine is idling while the...
Page 152 Starting Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle...
Page 153 Starting PREPARING TO START THE VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting the engine, avoid pressing the accelerator pedal before or during starting.
Page 154 Starting If starting a vehicle with an automatic transaxle: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: • Make sure the parking brake is set.
Page 155 Starting STARTING THE ENGINE 1. Turn the key to the start position (4) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to the on (3) position. 2. If the engine does not start within five seconds, wait ten seconds and try again.
Page 156 Starting USING THE ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater defroster system to respond quickly. It is strongly recommended if you live in a region where temperatures reach -23ºC (-10ºF) or below.
Page 157 Driving BRAKES Your brakes are self adjusting. Refer to the Scheduled Maintenance Guide" for maintenance intervals. Anti-lock braking system (ABS) (if equipped) On vehicles equipped with an anti lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
Page 158 Driving Operation of the anti-lock Two important rules braking system when braking in emergencies with The ABS operates by detecting the ABS: onset of wheel lock up during brake applications and compensating for this tendency. The wheels are prevented from locking even when the brakes are firmly applied.
Page 159 Driving Parking brake To engage the parking brake: Pull the handle upward. To release the parking brake: 1. Pull the handle up slightly. 2. Press and hold the release button. 3. Push handle downward to the off position. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic...
Page 160 Driving TRACTION CONTROL This system prevents wheel spin at all speeds. The control will toggle this function on and off, but the feature defaults to on after each cycle of the ignition key. The traction control system controls excessive wheel spin by automatically applying and releasing the brakes in conjunction with engine torque reductions.
Page 161 Driving STEERING YOUR VEHICLE Your vehicle comes with power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle changes at a constant vehicle speed, have the power steering checked.
Page 162 Driving Vehicles equipped with an automatic transaxle are equipped with a brake shift interlock feature that prevents the gearshift lever from being moved from the P (Park) position unless the brake pedal is depressed. Putting your vehicle in gear You must push the thumb button to move the gearshift to the position you choose.
Page 163 Driving On vehicles without the opening, insert a screwdriver or similar item about 5 cm (2 inches) inward, directly below the arrow symbol located to the right of the gearshift at the base of the console. 4. Rotate the screwdriver point rearward.
Page 164 Driving Driving Understanding gearshift positions To account for customer driving habits and conditions, your 2.5 l V6 automatic transaxle electronically controls the shift feel by using an adaptive learning strategy. During the first few hundred kilometers (miles) of operation, it is normal for your transaxle to adjust.
Page 165 Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll.
Page 166 Driving Deactivate D (Overdrive) when: • driving with a heavy load. • towing a trailer up or down steep hills. • additional engine braking is desired. To return to D (Overdrive) mode, press the transaxle control switch. The O/D OFF message in the instrument cluster will extinguish.
Page 167 Driving Manual transaxle (if equipped) Vehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. Using the clutch When starting a vehicle with a manual transaxle: 1. Hold down the brake pedal. 2.
Page 168 Driving Recommended shift speeds 2.0 litre engine 5-speed transaxle shift speed schedules Recommended During acceleration: During cruise*: upshifts: Shift from km/h km/h First to second Second to third Third to fourth Fourth to fifth 2.5 litre engine 5-speed transaxle shift speed schedules Recommended During acceleration: During cruise*:...
Page 169 Driving Parking 1. Apply the brake and the clutch and shift into neutral. 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition off. Do not park your vehicle in neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake.
Page 170 Driving LOADING YOUR VEHICLE Before loading your vehicle, familiarize yourself with these terms. Base curb weight Weight of the vehicle including any standard equipment, fluids and lubricants. It does not include passengers or aftermarket equipment. Payload Combined maximum allowable weight of passengers, cargo and optional equipment.
Page 171 Driving GVWR (Gross Vehicle Weight Rating) Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver's door pillar. GAWR (Gross Axle Weight Rating) Carrying capacity for each axle system (front and rear).
Page 172 Driving Payload = GVWR minus Base curb weight To obtain the correct weight for your vehicle, take your vehicle to a shipping company or an inspection station for trucks. Do not use replacement tires with lower weight capacities than the originals because they might lower the vehicle's GVWR and GAWR.
Page 173 Driving It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 174 (1 000 lb) trailer. Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers. Trailer towing puts additional loads on your vehicle's engine, transaxle, axle, brakes, tires, and suspension.
Page 175 Driving Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle's load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while towing a trailer in this chapter.
Page 176 Driving Do not exceed the maximum loads listed on the Safety Compliance Certification Label. For load specification terms found on the label, refer to Loading your vehicle in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight.
Page 177 Driving Using a hitch Do not use hitches that: • Clamp onto the vehicle bumper. • Attach to the axle. Distribute the load so that only 10 to 15% of the total weight of the trailer is on the tongue. Tie down the load so that it does not shift and change weight on the hitch.
Page 178 Driving Using trailer brakes Use electric brakes or manual, automatic or surge type hydraulic brakes that meet federal and local regulations. Install and adjust brakes according to the manufacturer's instructions. Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system.
Page 179 Driving Driving while towing a trailer Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer. Do not drive faster than 72 km/h (45 mph) with any weight trailer while towing in hilly terrain or on hot days.
Page 180 Driving FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular, scheduled maintenance, • excessive speed, • rapid acceleration, • driving with the brake pedal depressed, • sudden stops, • extended engine idling, • use of speed control in hilly terrain, •...
Page 181: Roadside Emergencies
Roadside emergencies HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown or approaching danger. Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. FUEL PUMP SHUT-OFF SWITCH If the engine cranks, but does not start or does not start after a collision, the fuel pump shut off...
Page 182 Roadside emergencies If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service. If your engine cranks but does not start after a collision or substantial jolt: 1.
Page 183 Roadside emergencies FUSES AND RELAYS If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Page 184 Roadside emergencies Power distribution box To check or replace a fuse or a relay, remove the cover of the fuse box in the engine compartment by releasing the latch (1) and lifting A blown fuse can be identified by a break in the wire.
Page 185 Roadside emergencies Fuses in the power distribution box (engine compartment) Fuse Ampere Color Description rating Not used blue Alternator yellow Fog lamps Heated seats Not used violet Engine management yellow Hazard lamps, horn, multifunction switch Not used blue Fuel pump Not used yellow Day time running light (Canada only)
Page 186 Roadside emergencies Relays in the power distribution box (engine compartment) Relay Color Description black Fuel pump black Engine management black Air conditioning black Low beam black High beam black Horn green Starter black High speed engine cooling fan dark green Engine cooling fan Not used green...
Page 187 Roadside emergencies A blown fuse can be identified by a break in the wire. All fuses are a push fit. Relays in the passenger compartment fuse panel (below instrument panel) Relay Color Description brown Courtesy lamps green Rear window defrost green Blower motor green...
Page 188 Roadside emergencies Passenger compartment fuse panel (below instrument panel) Fuse Ampere Color Description rating brown Mirror heater black Wipers orange Power roof, power windows brown ABS/TCS blue Turn signal lamps, backup lamps, speed control, gearshift lever, A/C clutch, blower motor blue Stop lamp, speed control yellow...
Page 189 Roadside emergencies CHANGING TIRES Park your vehicle in such a position where neither the traffic nor you are hindered or endangered when changing the tire. Ensure that the vehicle is on firm, level ground. Secure your vehicle further by blocking the wheels. Activate the hazard lights.
Page 190 Roadside emergencies The temporary spare tire The vehicle may have a high pressure temporary spare tire. This spare is smaller than a regular tire and is designed for emergency use only. Vehicles with traction control (if equipped) may exhibit some unusual driving characteristics which can be avoided by switching the system off.
Page 191 Roadside emergencies Spare tire location The spare tire and tools are located under the floor cover in the luggage compartment. Removing the spare tire and tools 1. Raise the rear of the floor cover in the luggage compartment and fold it forward. 2.
Page 192 Roadside emergencies Tire changing procedure Removing a tire 1. Apply the parking brake and 1 (First) gear (manual transaxle) or the P (Park) position (automatic transaxle). 2. Activate the hazard flashers. 3. The driver and all passengers must leave the vehicle. 4.
Page 193 Roadside emergencies Replacing a tire 1. Push the spare tire onto the wheel studs. 2. Screw on the wheel nuts, ensuring the tapered end of the wheel nuts are facing the wheel, and secure in a clockwise direction. 3. Lower the vehicle and remove the jack by turning the handle counterclockwise.
Page 194 Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing, if contacted.
Page 195 Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
Page 196 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery and...
Page 197 Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jump. A spark may cause an explosion of the gases that surround the battery. • 2.0 litre engine • 2.5 litre engine...
Page 198 Roadside emergencies 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed.
Page 199 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle's battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery.
Page 200 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook up and towing procedures for your vehicle.
Page 201 Roadside emergencies TOWING YOUR VEHICLE BEHIND ANOTHER VEHICLE At times you may want to tow your vehicle behind another vehicle. Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to off. •...
Page 202 Roadside emergencies Automatic transaxle In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle can be flat towed (all wheels on the ground) under the following conditions. •...
Page 203: Maintenance And Care
• We provide you with a Scheduled Maintenance Guide" which makes tracking routine service for your vehicle easy. If your vehicle requires professional service, your Ford or Lincoln/Mercury dealership can provide necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Page 204 Maintenance and care Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: • Do not work on a hot engine. The cooling fan is automatic and may come on at any time.
Page 205 Maintenance and care Working with engine off (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly.
Page 206 Maintenance and care Working with engine on (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Page 207 Maintenance and care Opening the hood • Pull the handle (1) located under the instrument panel. • Release the safety catch by reaching under the hood (2) and pushing it up. • Raise the hood and support it with the strut (3) in the yellow colored retainer, ensuring it is secure.
Page 208 Maintenance and care 2.0 litre EFI-engine compartment Power Engine Brake Automatic steering coolant fluid cleaner transaxle reservoir reservoir reservoir dipstick (if equipped) Battery Power Windshield Engine oil Engine oil distribution washer fluid dipstick filler cap reservoir For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black.
Page 209 Maintenance and care 2.5 litre EFI-engine compartment Power Engine Brake Automatic steering coolant fluid cleaner transaxle reservoir reservoir reservoir dipstick (if equipped) Battery Power Windshield Engine oil Engine oil distribution washer fluid dipstick filler cap reservoir For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black.
Page 210 Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start up engine noises or knock may be experienced.
Page 211 Maintenance and care It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. Checking the engine oil Check the engine oil each time you fuel your vehicle. To check the oil: Do not exceed MAX! 1.
Page 212 Maintenance and care 6. If the oil level is below the minimum line, add engine oil as necessary. If the oil level is beyond the maximum line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician.
Page 213 Refer to the Scheduled Maintenance Guide" for additional information. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. Always dispose of used automotive fluids in a responsible manner. Follow your community's standards for disposing of these types of fluids.
Page 214: Capacities And Specifications
Add only DOT 3 or DOT 4 brake fluid that meets the Ford specification (see the Capacities and specifications chapter). If you use DOT 5 or any other brake fluid that is not...
Page 215 Maintenance and care Cooling system – engine coolant The importance of engine coolant Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the proper concentration and fluid level in the coolant reservoir.
Page 216 Maintenance and care Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the Scheduled Maintenance Guide". The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -34°F (-36°C).
Page 217 Maintenance and care The cooling system in your vehicle is filled with Ford Extended Life Engine Coolant F6AZ 19544 AA or equivalent meeting Ford specification WSS M97B44 D. To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: •...
Page 218 Maintenance and care • Do not use alcohol or methanol or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant.
Page 219 Maintenance and care 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn the cap counterclockwise (left) until the pressure begins to release.
Page 220 Maintenance and care Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level.
Page 221 Use of recycled engine coolant Ford Motor Company does not recommend the use of recycled engine coolant in vehicles originally equipped with orange Extended Life coolant since a recycling process that produces orange coolant is not yet available.
Page 222 Maintenance and care Disposal of used engine coolant Used engine coolant should be disposed of in an appropriate manner. Follow your community's regulations and standards for recycling and/or disposal of automotive fluids. Checking and adding power steering fluid Check the power steering fluid twice a year.
Page 223 Maintenance and care Checking and adding automatic transaxle fluid Follow the scheduled service intervals outlined in the Scheduled Maintenance Guide". Your transaxle does not consume fluid. However, it is recommended that you refer to your "Scheduled Maintenance Guide" for scheduled intervals for fluid checks and changes.
Page 224 Maintenance and care 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P(Park) and leave the engine running.
Page 225 Maintenance and care High fluid level Fluid levels above the safe range may result in transaxle failure. An Do not add if above the overfill condition of transaxle fluid crosshatched area may cause shift and/ or possible damage. High fluid levels can be caused by an overheating condition, see note.
Page 226 Maintenance and care Battery Your vehicle may be equipped with a Motorcraft maintenance free battery. The Motorcraft maintenance free battery normally does not require additional water during its life of service. However, for severe service usage or in high temperature climates, refer to the Scheduled Maintenance Guide"...
Page 227 Maintenance and care Battery replacement If your original equipment battery requires replacement while under warranty, it will be replaced with a Motorcraft service battery, identical in design technology. Like the original equipment battery, it should not require water addition during its normal life of service; however, for severe service usage or in high temperature climates, refer to the Scheduled...
Page 228 Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 229 Maintenance and care Relearning the idle function Because your vehicle's engine is electronically controlled, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the computer must relearn" its idle conditions before your vehicle can drive properly.
Page 230 Traces of grease, silicone and fuel prevent wiper blades from functioning properly. We recommend Ford cleaning solutions or equivalent to clean wiper blades. Change the wiper blades on your vehicle at least once a year. Cabin air filter replacement...
Page 231 Maintenance and care 2. Remove the plastic caps from the screws on the grille. Remove the screws. 3. Open the hood. Pull off the rubber weatherstrip at the back of the engine compartment. Remove the screws that hold the grille, separate the two halves and remove the grille.
Page 232 Title 49 Code of Federal Regulation Part 575.104(c)(2). U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
Page 233 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1 1/2) times as well on the government course as a tire graded 100.
Page 234 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 235 Maintenance and care Checking tire pressure Check the tire pressure periodically after the vehicle has been parked for at least one hour or has been driven less than 5 km ( 3 miles). Inflate the tires as necessary. To check the tire pressure, insert the tire pressure gauge into the valve.
Page 236 Maintenance and care Replacing tires Replace tires at the latest when the wear band is visible through the tire treads. A tread depth of 3 mm or less will deteriorate the rain and snow performance of the vehicle. Your vehicle might be equipped with a 17"...
Page 237 Dispose of worn tires in accordance with local environmental regulations. Refer to the tire instruction decal to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle. When purchasing replacement tires for your vehicle, consult your...
Page 238 Maintenance and care Using snow tires and chains Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires.
Page 239 Maintenance and care IMPORTANT FUEL INFORMATION Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 240 Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Make sure the fuel cap is correctly fitted after fueling. Failure to do so may cause the on board diagnostic system to illuminate the...
Page 241 Maintenance and care Choosing the right fuel Use only unleaded fuel. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty. Your vehicle was not designed to use fuel containing manganese based additives such as MMT.
Page 242 Maintenance and care Octane recommendations Your vehicle is designed to use regular gasoline with an (R+M)/2 octane rating of 87. We do not recommend gasolines labeled as regular" in high altitude areas that are sold with octane ratings of 86 or even less.
Page 243 Maintenance and care Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating.
Page 244 Maintenance and care Fuel filler cap Your fuel tank filler cap has an indexed design with a one eighth turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops.
Page 245 Maintenance and care If you must replace the fuel 4. Use one of the following filler cap, replace it with an equations to calculate fuel authorized Motorcraft part. economy. The customer warranty may be Litres used x 100 / Total kilometres void for any damage to the fuel traveled tank or fuel system if an...
Page 246 Maintenance and care EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: •...
Page 247 Maintenance and care If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emissions control, such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 248 Maintenance and care Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 249 Maintenance and care Readiness for inspection/ maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on board diagnostic (OBD II) system. If your check engine" light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter.
Page 250 Maintenance and care BULB REPLACEMENT Removing the headlamps assembly Handle a halogen headlamp bulb carefully and keep out of children's reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 251 Maintenance and care Front turn signal Turn the bulb holder counterclockwise and pull it out. Pull the bulb out and replace it (1). Turn the socket counterclockwise and pull it out. Pull the bulb out and replace it (2). Opening the headlamp assembly Release the wire clip on the rear of the headlamp assembly and remove...
Page 252 Maintenance and care Headlamps – low beam Disconnect the electrical connector, turn the bulb holder counterclockwise and replace it. Do not touch the glass part of the bulb and pay attention to the tab guides when replacing. Headlamps – high beam Replacement instructions are the same as for the low beam headlamp.
Page 253 Reinstalling the headlamp assembly Make sure the locator pin is aligned with the bushing in the fender. All bulb connectors must be correctly connected. Install in the reverse order of removal. Foglamps (if equipped) Have these lamps replaced by a Ford Dealer.
Page 254 Maintenance and care Side marker lamps 1. Push the complete light assembly to the front and pull it out. 2. Remove the socket from the assembly by turning it counterclockwise. 3. Pull the bulb out and replace it. Brake/turn signal/tail/backup lamps 1.
Page 255 Maintenance and care License plate lamp Pry out the lamp with a flat blade screwdriver. Turn the socket counterclockwise and remove it. Pull the bulb out and replace it. Luggage compartment lamp Pry out the light assembly from the holder with a flat blade screwdriver. Turn the spherical bulb under slight pressure counterclockwise and remove.
Page 256 Maintenance and care Interior lamps Switch off the interior lamps (middle switch position). Pry out the lamp assembly with a flat screwdriver, release the reflector at the side and replace the bulb. To install, fit the new bulb in reverse sequence. Reading lamps (if equipped) Open the lamp assembly.
Page 257 Maintenance and care Headlamp aiming • Your vehicle is equipped with Driver side Passenger side headlamps designed to meet Visual (R) (L) aim requirements according to FMVSS 108, table 17 2. • Your headlamps are marked VOL [visual/optical (aiming) left]. This means that the left side of the light patterns for each low beam headlamp is used to aim the lamp...
Page 258 Maintenance and care • A screen or wall with a reference line (as described below) is needed in order to adjust the vertical position of each lamp's light pattern cut off line. The cut off line is the line formed between the bright lower portion and the dark upper portion of each lamp's light pattern.
Page 259 Maintenance and care Height of low beam lamp bulb center 7.6 meters 52 mm Height of reference line on wall Fig. 3 5. Turn on the low beam headlamps. Notice that both the driver's side lamp and the passenger's side lamp create similar Center line light patterns on the wall (see Fig.
Page 260 Maintenance and care VEHICLE CARE Washing your vehicle Only use car washing areas that have environmentally friendly drainage systems. Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
Page 261 Maintenance and care During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove, and they also cause damage to the vehicle. Remove or lower any exterior accessories before entering a car wash.
Page 262 Lacquer Touch up Paint (# ALBZ 19500 XXXXA) or Exterior Acrylic Spray Lacquer (# ALAZ 19500 XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle's specific coloring.
Page 263 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • Take care when using a power washer to clean the engine.
Page 264 Maintenance and care Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum based cleaners. Cleaning the exterior lamps Wash the exterior lamps with the same detergent you use to wash the exterior of your vehicle.
Page 265 Ford recommends using the Deluxe Leather Care Kit F8AZ 196253 AA, which is available from your Ford Dealer. This mild cleaner and special pad cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 266: Customer Assistance
Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Cleaning and caring for your vehicle Refer to the Customer Assistance Guide" for a list of Ford approved cleaners, polishes and waxes.
Page 267: Capacities And Specifications
Capacities and specifications Motorcraft parts Part number 2.5 litre Component 2.0 litre engine 2.5 litre engine Cougar S AZFS 22F # 1+2** Spark plug* AWSF 32F AWSF 22FS AZFS 22FE # 3+4 Air filter FA 1612 FA 1613 FA 1611 Cabin air filter Fuel filter FG 800A...
Page 268 Capacities and specifications Capacities 2.0 litre engine 2.5 litre engine Engine oil - with filter 4.25 l (4.5 qts) 5.5 l (5.8 qts) - without 3.75 l (4.0 qts) 5.0 l (5.3 qts) Manual transaxle 2.6 l (2.7 qts) Automatic transaxle 9.6 l (10.2 qts) Power steering Fill to MAX mark...
Page 269 Capacities and specifications Lubricant specifications Ford part name Ford part Ford Item or equivalent number specification High Performance ESA M6C25 A DOT 3 Brake (North Amer C6AZ 19542 AB Fluid (North Brake fluid ica) or for DOT 3 America) or DOT...
Page 270 Capacities and specifications Engine data 2.0 litre 2.5 litre 2.5 litre Engine engine engine Cougar S Cubic capacity 1988 2495 2495 Power output kW(HP) 96(125) 125 (170) 151 (195) at rpm 5500 6250 6600 Max torque Nm (lb ft.) 176 (130) 220 (162) 229 (169) at rpm...
Page 271 Capacities and specifications Dimensions mm (inches) A = Overall length 4720 (186) B = Overall width (without mirrors) 1769 (69.6) C = Overall height (curb weight) 1325 (52.2) D = Wheelbase 2704 (106.5) E = Track front 1506 (59.3) rear 1491 (58.7)
Page 272 Capacities and specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is attached to a metal tag and is located on the front driver's side of the instrument panel. The VIN tag may be seen by looking through the windshield from the outside of the vehicle.
Page 273: Customer Assistance
To obtain information about by contacting your Ford or reimbursement, call 1 800 241 3673 Lincoln Mercury dealer. in the United States for Ford or Roadside assistance will cover Mercury vehicles; or if you own a • changing a flat tire Lincoln vehicle, call 1 800 521 4140.
Page 274 Ford Motor your dealer for complete details Company or Ford Motor Service about Ford Extended Service Plan Company (in the U.S.) and Ford of coverage options. Canada (in Canada). It provides: Also, please be aware that some •...
Page 275 Away from home If you are away from home when At home your vehicle needs service, or if you Ford Motor Company and Ford of need more help than the dealership Canada have authorized dealerships could provide after following the to service your vehicle.
Page 276 Ford, Dispute Settlement Board before Mercury and Lincoln cars and Ford, taking action under the Mercury and Lincoln light trucks Magnuson Moss Warranty Act, or to...
Page 277 The Board consists of: with warranty repairs or concerns • three consumer representatives with the vehicle's performance as designed • a Ford or Lincoln Mercury dealership representative • a request for reimbursement of consequential expenses unless a Consumer candidates for Board...
Page 278 Every effort is made to decide the • a brief summary of the action case within 40 days of the date that taken by the dealer(s) and Ford all requested information is Motor Company received by the Board. Since the •...
Page 279 Administrator directly at UTILIZING THE 1 800 207 0685. MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory related vehicle service concern have been unsatisfactory,...
Page 280 If the dealership registration regulations and where employees cannot help you, they to find unleaded fuel. can direct you to the nearest Ford affiliate office. If you cannot find unleaded fuel or can only get fuel with an anti knock...
Page 281 Ford, Lincoln Mercury finishes. For best results, use the or Ford of Canada dealer. These following or products of equivalent quality accessories have been quality specifically engineered to fulfill your automotive needs;...
Page 282 Customer assistance Comfort and convenience Travel equipment Air conditioner Console Air filtration systems Console armrest Cargo nets Daytime running lights Cargo organizers Factory luggage rack Cargo shades Factory luggage rack adapters Cargo trays Fog lights Dash trim Framed luggage covers Engine block heaters Heavy duty battery Gear shift knob...
Page 283 Customer assistance For maximum vehicle performance, Protection and appearance keep the following information in equipment mind when adding accessories or Air bag anti theft locks equipment to your vehicle: Bed mat/bedliner tailgate covers • When adding accessories, Bed mats equipment, passengers and luggage to your vehicle, do not exceed the Bedliners total weight capacity of the vehicle...
Page 284 EST., of five watts or less will not for credit card holders only. ordinarily affect your vehicle's operation.) • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
Page 285: Reporting Safety Defects (U. S. Only)
National Highway Traffic Safety Administration (NHTSA) in addition to Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 286: Index
Index Page Page Air bag disposal ... . Backup lamps ....Air bag readiness light ..Base curb weight .
Page 287 Index Page Page Children and air bags ..Electrical system ... Children and safety belts ..Emergencies, roadside ..Children and safety restraints Emission control system .
Page 288 Index Page Page Fuel gauge ....Hazard flasher control ..86, 180 Fuel pump shut off switch 97, 180 Head restraints .
Page 289 Index Page Page Jack ..... . Maintenance and care ..Jack positioning ... . Manual transaxle .
Page 290 Index Page Page Panel dimmer control ..Reading lamps ....Panic alarm ....Reading lamps, replacing bulbs .
Page 291 Index Page Page Safety defects, reporting ..Tachometer ....Safety restraint locking modes 116 Tail lamps ....Safety restraints .
Page 292 Index Page Used automotive fluids, disposal ....Vehicle care ....Vehicle Emission Control Information (VECI) .
Page 297: Filling Station Information
Fuel tank capacity Use Super Premium SAE 5W 20 Motor Oil or equivalent meeting Engine oil Ford specification WSS M2C153 H Refer to the tire instruction decal Tire size and pressure on the passenger's door Pull handle under the left side of...

Ford 2001 Mercury Cougar Owner's Manual

Quick Links

Related Manuals for Ford 2001 Mercury Cougar

Summary of Contents for Ford 2001 Mercury Cougar

Table of Contents