Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 3: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 4 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. EMISSION WARRANTY The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power...
Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Child Seat Tether Installation Warning Anchorage Anti-Lock Brake Brake System System Brake Fluid -...
Page 6 Introduction Vehicle Symbol Glossary Power Windows Power Window Front/Rear Lockout Interior Luggage Child Safety Door Compartment Lock/Unlock Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Battery Avoid Smoking, Battery Acid Flames, or Sparks Explosive Gas Fan Warning Power Steering...
Page 7: Instrumentation
Instrumentation Instrument Driver air bag cluster (pg. 88) (pg. 8) Headlamp control (pg. 18) Instrument panel dimmer control (pg. 19) Turn signal Speed controls control (pg. 53) (pg. 51) Wiper/washer control (pg. 51) * if equipped...
Page 8 Instrumentation Climate control system (pg. 20) Audio system (pg. 24) Foglamp control* (pg. 19) Traction Overdrive off Rear Auxiliary power point control switch switch defroster* (pg. 60) (pg. 111) (pg. 117) (pg. 19)
Page 9: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster 60 70 RPMX1000 80 100 120 1 10 km/h SELECT/RESET 0 0 0 0 0 FUEL DOOR SERVICE CHECK BRAKE THEFT ENGINE FUEL FUEL SOON Optional instrument cluster RPMX1000 120 140 km/h SELECT/RESET 0 0 0 0 0 FUEL DOOR...
Page 10: Controls And Features
Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Page 11: Driving
Instrumentation The Service Engine Soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Page 12 Instrumentation Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap (if equipped) Momentarily CHECK illuminates when the FUEL ignition is turned to the ON position to ensure your bulb is working.
Page 13 Instrumentation O/D off (if equipped) Illuminates when the Transmission Control Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation.
Page 14 Instrumentation Brake system warning Momentarily illuminates BRAKE when the ignition is turned to the ON position to ensure the circuit is functional. Also illuminates if the parking brake is engaged. If brake warning lamp does not illuminate at these times, seek service immediately. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately.
Page 15: Fuel Gauge
Instrumentation GAUGES Base instrument cluster gauges 60 70 RPMX1000 80 100 120 1 10 km/h SELECT/RESET 0 0 0 0 0 FUEL DOOR SERVICE CHECK BRAKE THEFT ENGINE FUEL FUEL SOON Optional instrument cluster gauges RPMX1000 120 140 SELECT/RESET km/h 0 0 0 0 0 FUEL DOOR SERVICE...
Page 16: Engine Coolant Temperature Gauge
Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 17 Instrumentation Odometer Registers the total kilometers (miles) of RPMX1000 the vehicle. SELECT/RESET 0 0 0 0 0 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer at the top of the scale or in the red zone may damage the engine. •...
Page 18 Instrumentation Trip odometer Registers the kilometers (miles) of RPMX1000 individual journeys. Press and release the reset button until a “T” appears in the display SELECT/RESET (this represents the 0 0 0 0 0 trip mode). Press and hold the button for three seconds to reset.
Page 19: Controls And Features
Controls and features HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps).
Page 20 Controls and features Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: • Parking lamps • Low beams Press the foglamp control to activate the foglamps. The foglamp indicator light will illuminate. When the highbeams are activated, the foglamps will not operate.
Page 21 Controls and features • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position.
Page 22 Controls and features The air conditioning compressor can operate in all modes except . However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
Page 23 Controls and features cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.
Page 24 Controls and features cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired. •...
Page 25: Using Your Audio System
Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Single CD DISC VOL PUSH ON FM 1 MUTE TAPE AUTO DOLBY B NR SEEK TUNE SCAN BASS TREB FADE SIDE 1-2 COMP SHUFFLE Volume/power control Press the control to VOL - PUSH ON turn the audio system on or off.
Page 26 Controls and features AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play.
Page 27 Controls and features Tune adjust for CD changer (if equipped) • Press to select SEEK SEEK the previous disc in TUNE TUNE the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.
Page 28 Controls and features Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three SEEK SEEK seconds or more and you press , the TUNE TUNE...
Page 29 Controls and features Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 30 Controls and features 2. Press the AUTO control. AUTO 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 31 Controls and features Press the TREB control then press: • to decrease the treble output and • to increase the treble output. Speaker balance adjust Speaker sound FADE distribution can be adjusted between the right and left speakers. Press the BAL control then press: •...
Page 32 Controls and features • To begin CD play (if TAPE CD(s) are loaded), press the CD control. The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last. With the dual media audio system, press the CD control to toggle between single CD and CD changer play (if equipped).
Page 33 Controls and features Eject function Press the EJ control to stop and eject a tape. Press the EJ control to stop and eject a CD. Dolby noise reduction Dolby noise reduction operates in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback.
Page 34 Controls and features Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Setting the clock To set the hour, press and hold the CLK AUTO control and press SEEK: •...
Page 35 Controls and features The CLK button will allow you to switch AUTO between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
Page 36 Controls and features Volume/power control Press the control to turn the audio system on or off. PUSH ON Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 37 Controls and features Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 38 Controls and features the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing. • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay.
Page 39 Controls and features 4. Press and hold a memory preset control. The playing media will mute momentarily. When the sound returns, the station is held in memory on the control you selected. The display will read SAVED. Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations.
Page 40 Controls and features If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs. NO CD will display if the CD control is activated when there is not a CD present in the audio system.
Page 41 Controls and features choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2.
Page 42 Controls and features Auto eject Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD.
Page 43 Controls and features When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK. SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system. SHUFFLE TRK plays all the tracks on the current disc in random order.
Page 44 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the FADE right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Page 45 Controls and features When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF. SELECT HOURS, SELECT MINUTES— Allows you to adjust the hours and minutes. Refer to Setting the clock. TRAFFIC ON/OFF— Traffic announcements can be programmed as local or distant.
Page 46 Controls and features When in this mode, traffic announcements will interrupt radio and CD play. • Press the MENU control until TRAFFIC is displayed. • Press the SEL control to engage the feature. The display will read TRAFFIC ON. This feature also allows you to control the volume of traffic announcements.
Page 47 Controls and features Show This feature allows you to select the type of MENU RDS broadcast information the radio will regularly show in the display. With RDS activated, press the MENU MENU control until SHOW is displayed. Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display).
Page 48 Controls and features • JAZZ CLUB—jazz club with clearly reflected sounds • HALL—rectangular concert hall capacity of about 2 000 • CHURCH—church with a high vault • STADIUM—outdoor stadium with a capacity of about 30 000 Press the DSP control again to access the occupancy modes.
Page 49 Controls and features Troubleshooting the CD player (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty.
Page 50 Controls and features Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation.
Page 51 Controls and features • Terrain.Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.
Page 52 Controls and features TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers.
Page 53 Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. For manual transmission, you must depress the ignition release lever. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Page 54 Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 55 Controls and features If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your...
Page 56 Controls and features To set a lower set speed • Press and hold COAST. Release the RESUME control when the desired speed is ACCEL reached or • Press and release COAST COAST to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or •...
Page 57 Controls and features Pressing OFF will erase the previously programmed set speed. To return to a previously set speed • Press RESUME. For RESUME to operate, RESUME the vehicle speed must be faster than ACCEL 48 km/h (30 mph). COAST INTERIOR LAMPS Map lamps (if equipped) If equipped with a...
Page 58 Controls and features • Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press the top portion of the driver window control completely down and release quickly.
Page 59 Controls and features POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Move the mirror selector control all the way to the left to adjust the left mirror or all the way to the right to adjust the right mirror. 2.
Page 60 Controls and features The transmission will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again. The O/D OFF indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode.
Page 61 Controls and features AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The power point is an additional power source for electrical accessories.
Page 62 Controls and features CONVERTIBLE (IF EQUIPPED) Do not store articles behind rear seat. Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered. Lowering the convertible top The convertible top can be lowered with the side windows either up or down.
Page 63 Controls and features 6. Push the convertible top switch on the console in front of the armrest and hold until the top is completely stored. 7. Disengage the parking brake. Installation of the boot 8. Push boot rearward and engage boot under the body molding at the rear and sides.
Page 64 Controls and features 11. To remove unfasten the snaps and the boot tongue. 12. Pull forward and lift off. Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged.
Page 65 Controls and features REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 66 Controls and features Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within three seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps and the chime may sound, reminding you to properly close all doors.
Page 67 Controls and features Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the START/RUN or ACC position.
Page 68 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Page 69 Controls and features Automatic arming The vehicle is armed immediately after switching the ignition to the 3 (OFF) THEFT position. The light in the instrument cluster will flash every two seconds when the vehicle is armed. Automatic disarming Switching the ignition to the 4 (ON) position with a THEFT coded key disarms the vehicle.
Page 70 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key ignition key is an approved Ford coded key ignition key. If your keys are lost or stolen you will need to do the following: •...
Page 71 Controls and features Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one second).
Page 72 Controls and features INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle.
Page 73 Controls and features Keep vehicle doors and luggage compartment locked and keep keys out of a child’s reach. Unsupervised children could lock themselves in an open trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
Page 74: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 75 Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 76 Seating and safety restraints The control is located on the front outboard corner of the driver’s seat. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Page 77 Seating and safety restraints The rotating boot on the front seat belt is designed to allow rear seat entry/exit. To enter the rear seat: 1. Remove seat belt from seat belt holder on top of front seat. 2. Rotate the safety belt boot rearward.
Page 78 Seating and safety restraints To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 79 Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Energy Management Feature • This vehicle has a safety belt system with an energy management feature at the front passenger seating position to help further reduce the risk of injury in the event of a head-on collision.
Page 80 Seating and safety restraints Combination lap and shoulder belts Before fastening the safety belt, make sure the shoulder belt passes through the belt holder on the top of the seatback. Coupe shown, convertible is similar and safety belt must also pass through the belt holder.
Page 81 Seating and safety restraints suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. The safety belt system can also be made to lock manually by quickly pulling on the shoulder belt.
Page 82 This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Page 83 Seating and safety restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Page 84: Belt Minder
Seating and safety restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning buckled before the ignition light illuminates1-2 minutes switch is turned to the ON and the warning chime position... sounds 4-8 seconds. The driver’s safety belt is The safety belt warning buckled while the indicator...
Page 85 3 of 4 fatal crashes occur within 25 far” miles of home. “Belts are Ford designs its safety belts to enhance uncomfortable” comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 86 Seating and safety restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 87 Seating and safety restraints 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.
Page 88 (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a...
Page 89 This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 90 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer.
Page 91 Seating and safety restraints Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury. Do not modify the front end of the vehicle.
Page 92 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 93 Seating and safety restraints considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control.
Page 94 Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. •...
Page 95 Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards.
Page 96 Seating and safety restraints provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the...
Page 97 Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 98 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions If you must use a forward facing child seat in the front seat (reminder - children 12 years old and under should always be properly restrained in the rear seat) the shoulder belt must...
Page 99 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 100 Seating and safety restraints 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child...
Page 101 Seating and safety restraints The tether anchors in your vehicle are either located under a cover marked with the child tether anchor symbol (shown with title) or are under a flap in the convertible top boot. The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap...
Page 102 Seating and safety restraints 5. Clip the tether strap to the anchor as shown. For Convertible only: The tether anchors on the convertible are located on the lower backside of the seatback. 4. Access tether anchors located behind the seatback and pull away vinyl cover to expose anchors.
Page 103 Seating and safety restraints If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.
Page 104 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 105 Starting Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than 10 minutes at high engine RPM.
Page 106: The Vehicle
Starting 3. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely. This condition may occur when: •...
Page 107 Starting STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 108 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.
Page 109 Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 110 Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Page 111 Driving stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Hydraulic brake booster system (Hydroboost) The Hydroboost system receives fluid pressure from the power steering pump to provide power assist during braking.
Page 112 Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Page 113 Driving reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly.
Page 114 Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 115: Roadside Emergencies
Driving 2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N (Neutral). 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Page 116 Driving Driving with an automatic overdrive transmission with console gearshift and O/D off switch Your automatic overdrive transmission provides fully automatic operation in either D (Overdrive) or with the O/D OFF switch depressed. Driving with the gearshift lever in D (Overdrive) gives the best fuel economy for normal driving...
Page 117 Driving Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park).
Page 118 Driving (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
Page 119 Driving To return to (Overdrive) mode, press the transmission control switch. The O/D OFF indicator will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired.
Page 120 Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1.
Page 121: Parking Your Vehicle
Driving • Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will greatly reduce clutch life. Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph).
Page 122 Driving 4. Turn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse You must be at a complete stop to shift into R (Reverse).
Page 123 Driving 6. Slowly release the clutch pedal. Removing key from ignition • Turn the ignition key to position 3 (OFF). • Push the release lever forward and rotate the key towards you and remove. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface.
Page 124 Driving • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification.
Page 125 Driving • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the certification label.
Page 126 Driving tongue load of 45 kg (100 lbs.). Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). Towing a trailer places an additional load on your vehicle’s engine, transaxle, brakes, tires and suspension.
Page 127 Driving Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Page 128 Driving Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. •...
Page 129 If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 130: Roadside Emergencies
• for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60 000 km (36 000 miles), whichever comes first on Ford and Mercury vehicles, and four years or 80 000 km (50 000 miles) on Lincoln vehicles Roadside assistance will cover: •...
Page 131 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB...
Page 132 Roadside emergencies After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located on the left side of the trunk behind teh left rear tail light and the trunk liner.
Page 133: Passenger Compartment Fuse Panel
Roadside emergencies Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Cartridge...
Page 134 Roadside emergencies OWNERS MANUAL FUSE INFO The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Cigar Lighter Engine Controls — Not Used RH Low Beam Headlamp Instrument Cluster, Traction Control Switch Starter Motor Relay GEM, Interior Lamps Engine C ontrols —...
Page 135 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Electronic Flasher Power Mirror Switch, GEM, Anti-Theft Relay, Power Door Locks, Door Ajar Switches Convertible Top Switch Instrument Cluster and Engine Control Memory — Not Used A/C Clutch, Defogger Switch Climate Control Blower Motor Luggage Compartment Lid Release...
Page 136 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 137 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description Relay 1 — Fog Lamp Interrupt Relay 2 — Int. Wiper Relay 3 — Wiper HI/LO Relay 4 — Starter Relay 5 —...
Page 138 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 30A** Rear Window Defrost Control 40A** Power Windows, Power Locks — Not Used 20A* Fuel Pump — Not Used 20A* Horn 20A* Anti-Lock Brake System 30A* Power Seats — Not Used 20A* Generator...
Page 139 Roadside emergencies If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: •...
Page 140 Roadside emergencies 3. Remove the spare tire, jack and lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the tire you are changing.
Page 141 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with...
Page 142 Roadside emergencies To remove the anti-theft lug nut: 1. Insert the key over the locking lug nut. Make sure you hold the key square to the lug nut. If you hold the key at an angle, you could damage the key and the lug nut. 2.
Page 143 Roadside emergencies shift firmly. This operation is considered normal and will not effect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation to its optimum shift feel. 1. Use only a 12–volt supply to start your vehicle.
Page 144 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 145 Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.
Page 146 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery.
Page 147 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using...
Page 148: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 149 Maintenance and care 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First).
Page 150 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 151 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Windshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8.
Page 152 Maintenance and care 4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Windshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9.
Page 153 Maintenance and care 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
Page 154 Maintenance and care • 3.8L V6 engine • 4.6L SOHC V8 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated.
Page 155 If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Page 156 Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. • 3.8L OHV V6 engine • 4.6L SOHC V8 engine 1.
Page 157: Capacities And Specifications
Maintenance and care 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 158 In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification . Refer to Lubricant specifications in the Capacities and specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 159 Maintenance and care The level of coolant should be maintained at the “cold full” of “cold fill range” level in the coolant reservoir. If the level falls below, add coolant per the instructions in the Adding Engine Coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration.
Page 160 Maintenance and care When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” as listed on the engine coolant reservoir. • Refer to the scheduled maintenance guide for service interval schedules.
Page 161 Maintenance and care The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir.
Page 162 • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). If equipped with the 3.8L V6 engine, to avoid scalding hot steam or coolant from...
Page 163 Maintenance and care Engine coolant refill procedure-3.8L V6 engine Use the following procedure when refilling the cooling system of a vehicle equipped with a 3.8L V6 engine. Failure to follow this warning may result in damage to the engine and engine cooling system.
Page 164 Maintenance and care 13. Reinstall the radiator cap. 14. Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool). 15. If necessary, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level”...
Page 165 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored).
Page 166 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 167 Maintenance and care • refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
Page 168 Maintenance and care 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir. If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at...
Page 169 Maintenance and care Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking.
Page 170 Maintenance and care a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. You can check the fluid without driving if the ambient temperature is above 10°C (50°F). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature.
Page 171 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 172 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 173 Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting...
Page 174 Maintenance and care 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute.
Page 175 Maintenance and care WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted...
Page 176 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 177 Maintenance and care Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
Page 178 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). •...
Page 179 If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford.
Page 180 Maintenance and care Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 181 Maintenance and care • If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.
Page 182 Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed.
Page 183 Maintenance and care soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.
Page 184 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...
Page 185 Maintenance and care Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty. Octane recommendations Your vehicle is designed to use “Regular” unleaded (R+M)/2 METHOD gasoline with pump (R+M)/2 octane rating of 87.
Page 186 Canada, look for fuels that display the Auto Makers’ Choice logo. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 187 Maintenance and care Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver.
Page 188 Maintenance and care For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium —...
Page 189 Maintenance and care Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy.
Page 190 Maintenance and care • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance •...
Page 191 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 192 Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the...
Page 193 Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: •...
Page 194 Maintenance and care Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly.
Page 195 Maintenance and care To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 196 Maintenance and care 3. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly. 4. Pull headlamp assembly forward disengaging the lamp from the rear snap retainers to expose the back of the bulb. 5.
Page 197 Maintenance and care Replacing foglamp bulbs The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope.
Page 198: Map Lamp
Maintenance and care Interior bulbs Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Map lamps For bulb replacement, see a qualified service technician or your dealer. Using the right bulbs Replacement bulbs are specified in the chart below.
Page 199 Maintenance and care AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Headlamp vertical aim adjustment 1.
Page 200: Customer Assistance
7. Close the hood and turn off the lamps. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 201 Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), Lacquer Touch-up Paint (ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring.
Page 202 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry...
Page 203 Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water.
Page 204 Maintenance and care • Do not spray with cold water to avoid cracking the engine block or other engine components. • Never apply anything to the drive belt (including belt dressing). • Cover the highlighted areas to prevent water damage when cleaning the engine. •...
Page 205 Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
Page 206 Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 207: Capacities And Specifications
If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter as shown on the engine decal. REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High Performance Fill to line on...
Page 208 Fill 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Ensure the correct automatic transmission fluid is used.
Page 209: Lubricant Specifications
Capacities and specifications Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. LUBRICANT SPECIFICATIONS Item Ford part name Ford part Ford number specification Brake fluid High Performance...
Page 210: Engine Data
Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water.
Page 211: Vehicle Dimensions
Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions Coupe mm (in) Convertible mm (in) (1) Overall length 4 653.3 (183.2) 4 653.3 (183.2) (2) Overall width 1 856.7 (73.1) 1 856.7 (73.1) (3) Overall height 1 348.7 (53.1) 1 351.3 (53.2) (4) Wheelbase 2 573.0 (101.3) 2 573.0 (101.3)
Page 212: Certification Label
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway MFD. BY FORD MOTOR CO. IN U.S.A. Traffic Safety DATE: XXXXX GVWR:XXXXXXXXXXXX FRONT GAWR: XXXXXX/XXXXXXX Administration REAR GAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL Regulations require MOTOR VEHICLE SAFETY, BUMPER, AND THEFT PRE-...
Page 213: Customer Assistance
Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 214 Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs.
Page 215 Customer assistance Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 216 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business) •...
Page 217 • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 218 Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Page 219 • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve...
Page 220 Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 221 CAMVAP decisions are fast, fair, and final; the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces, except Quebec. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.
Page 222 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 223 Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs;...
Page 224 Customer assistance Not all accessories are available for all models. Vehicle Security Styled wheel locks Vehicle security systems Comfort and convenience Ash Cup Cargo nets Cargo organizers Dash trim Electrochromic mirror with compass Electrochromic mirror with compass and temperature display Engine block heaters Travel equipment Auto headlamps with daytime running lights (DRL)
Page 225 Customer assistance Front end covers (full and mini) Lubricants and oils Molded splash guards Seat belt extenders Tonneau covers (mini) Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
Page 226 Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that,...
Page 227 Customer assistance California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 29 000 km (18 000 miles), whichever occurs first: 1.
Page 228: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 229: Index
Index Axle lubricant Air bag supplemental specifications . 208–209 restraint system ..88 refill capacities ..206 and child safety traction lok .... 122 seats ......90 description ....88 disposal ....93 driver air bag ..91 Battery ..... 171 indicator light ..
Page 230 Speed control) ..53 instrument panel .. 204 Customer interior ... 204–205 Assistance ....129 mirrors ....201 Ford accessories for plastic parts ..201 your vehicle ..221 safety belts .... 204 Ford Extended Service washing ....199 Plan ......212 waxing ....
Page 231 Index The Dispute refill capacities ..206 Settlement service Board ..... 216 points ..... 150–151 Utilizing the starting after a Mediation/Arbitration collision ....130 Program ....219 Engine block heater ....... 106 Engine oil ....151 checking and Daytime running lamps adding ....
Page 232 Index fuel pump shut-off driving with a heavy switch ....130 load ......122 gauge ....... 14 location ....122 improving fuel GVWR (Gross Vehicle economy ....186 Weight Rating) ..122 low fuel warning calculating ..... 122 light ......11 definition ....
Page 233 Index Instrument panel interior cleaning ....204 lamps ....56, 197 cluster ....8, 204 replacing lighting up panel and bulbs ....192–196 interior ..... 19 Lane change indicator location of (see Turn signal) ..51 components ....8 Lights, warning and indicator ......
Page 234 Index fluid, refill capacity ....206 Manual fluid, transmission .... 119 specifications 208–209 fluid capacities ..206 lubricant specifications ..209 reverse ....121 Radio ......24 Mirrors Relays ...... 131 cleaning ....201 Remote entry side view mirrors system ....64–65 (power) ....
Page 235 Index Safety seats for snow tires and children ...... 95 chains ....179 tire grades ..... 176 Seat belts (see Safety treadwear ....175 restraints) ....76 Towing ..... 124 Seats ......73 recreational child safety seats ..95 towing ....127 cleaning ..
Page 236 Index Vehicle loading ..122 Windows power ....... 56 Ventilating your vehicle ...... 107 Windshield washer fluid and wipers checking and adding fluid ......157 Warning chimes ..13 checking and cleaning ....174 Warning lights (see operation ....51 Lights) ......
Page 240: Filling Station Information
Washer Concentrate. Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used.
Page 241 Filling station information MERCON V are not interchangeable. DO NOT mix MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface.

This manual is also suitable for:

Mustang gt 2001

Ford Mustang 2001 Owner's Manual

Quick Links

Related Manuals for Ford Mustang 2001

Summary of Contents for Ford Mustang 2001

This manual is also suitable for:

Table of Contents