Toshiba MMD-VNK502HEXE Installation Manual page 31

Air to Air Heat Exchanger with DX Coil Unit
Checking the Settings of the Indoor units
Before handing the system over to the customer, check the addresses and settings of the indoor units, then fill in
the check sheet below. When you have installed a group control system, fill in the check sheet for each system and
for each indoor unit. (You can enter the settings of 4 indoor units in to one check sheet.)
NOTE
For maintenance after installation, fill in the check sheet and hand over this Installation manual to the customer.
Indoor unit settings check sheet
Indoor unit Indoor unit
Model name Model name
Check the addresses of the indoor units. (For details, see "Advanced control" in this manual.)
(Code: [12] for the system, [13] for indoor units, and [14] for groups)
Line Indoor Group Line Indoor
Settings Settings
Did you change the setting for the lighting-up hours of the Filter Sign?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Lighting-up hours of the Filter Lighting-up hours of the Filter
Sign Sign
(Code: [01]) (Code: [01])
No change No change
None [0000] None [0000]
150H [0001] 150H [0001]
2500H [0002] 2500H [0002]
5000H [0003] 5000H [0003]
10000H [0004] 10000H [0004]
Did you change the setting for the single operation of the Air to Air Heat Exchanger with direct expansion coil?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Single operation of the Air to Air Single operation of the Air to Air
Heat Exchanger with direct Heat Exchanger with direct
expansion coil expansion coil
(Code: [31]) (Code: [31])
No change No change
No [0000] No [0000]
Yes [0001] Yes [0001]
Did you change the setting for the imbalance ventilation operation?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Imbalance ventilation operation Imbalance ventilation operation
(Code: [48]) (Code: [48])
No change No change
Normal [0000] Normal [0000]
SA (High) > [0001] SA (High) > [0001]
EA (Low) EA (Low)
active active
SA (Low) < [0002] SA (Low) < [0002]
EA (High) EA (High)
active active
* "High" may be "Extra High". * "High" may be "Extra High".
59-EN
Installation Manual
Indoor unit Indoor unit
Model name Model name
Group Line Indoor Group Line Indoor
Settings Settings
Lighting-up hours of the Filter Lighting-up hours of the Filter
Sign Sign
(Code: [01]) (Code: [01])
No change No change
None [0000] None [0000]
150H [0001] 150H [0001]
2500H [0002] 2500H [0002]
5000H [0003] 5000H [0003]
10000H [0004] 10000H [0004]
Single operation of the Air to Air Single operation of the Air to Air
Heat Exchanger with direct Heat Exchanger with direct
expansion coil expansion coil
(Code: [31]) (Code: [31])
No change No change
No [0000] No [0000]
Yes [0001] Yes [0001]
Imbalance ventilation operation Imbalance ventilation operation
(Code: [48]) (Code: [48])
No change No change
Normal [0000] Normal [0000]
SA (High) > [0001] SA (High) > [0001]
EA (Low) EA (Low)
active active
SA (Low) < [0002] SA (Low) < [0002]
EA (High) EA (High)
active active
* "High" may be "Extra High". * "High" may be "Extra High".
Air to Air Heat Exchanger with DX Coil Unit
Indoor unit
Model name
Check the addresses of the indoor units. (For details, see "Advanced control" in this manual.)
(Code: [12] for the system, [13] for indoor units, and [14] for groups)
Line Indoor Group
Settings
Did you change the setting for the nighttime heat purge operation?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Nighttime heat purge operation Nighttime heat purge operation
(Code: [4C]) (Code: [4C])
No change
Nighttime [0000]
heat purge
OFF
Start after [0001]-
[0048]
the setting
value x 1
hour(s)
Group
Did you change the setting for the linked operation with external devices?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Setting of the linked operation Setting of the linked operation
with external devices with external devices
(Code: [4E]) (Code: [4E])
No change
ON/OFF [0000]
linked
ON linked [0001]
OFF linked [0002]
Did you change the setting for changing the ventilation mode?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Changing the ventilation mode Changing the ventilation mode
(Code: [EA]) (Code: [EA])
No change
[0002]
Heat
exchange
mode
[0003]
Automatic
mode
Compatible with RBC-AMT32E Compatible with RBC-AMT32E
Did you change the setting for changing the ventilation FAN speed?
If you did not, put a tick against "No change". If you did, put a tick against the item you selected.
(For details, see "Advanced control" in this manual.)
Changing the ventilation FAN Changing the ventilation FAN
speed speed
(Code: [EB]) (Code: [EB])
No change
High [0002]
Low [0003]
Imbalance [0004]
* "High" may be "Extra High". * "High" may be "Extra High".
Compatible with RBC-AMT32E Compatible with RBC-AMT32E
– 30 –
Indoor unit Indoor unit
Model name Model name
Line Indoor Group Line Indoor Group
Settings Settings
Nighttime heat purge operation
(Code: [4C])
No change No change
Nighttime [0000] Nighttime [0000]
heat purge heat purge
OFF OFF
Start after [0001]- Start after [0001]-
[0048] [0048]
the setting the setting
value x 1 value x 1
hour(s) hour(s)
Setting of the linked operation
with external devices
(Code: [4E])
No change No change
ON/OFF [0000] ON/OFF [0000]
linked linked
ON linked [0001] ON linked [0001]
OFF linked [0002] OFF linked [0002]
Changing the ventilation mode
(Code: [EA])
No change No change
[0002] [0002]
Heat Heat
exchange exchange
mode mode
[0003] [0003]
Automatic Automatic
mode mode
Compatible with RBC-AMT32E
Changing the ventilation FAN
speed
(Code: [EB])
No change No change
High [0002] High [0002]
Low [0003] Low [0003]
Imbalance [0004] Imbalance [0004]
* "High" may be "Extra High".
Compatible with RBC-AMT32E
Installation Manual
Indoor unit
Model name
Line Indoor Group
Settings
Nighttime heat purge operation
(Code: [4C])
No change
Nighttime [0000]
heat purge
OFF
Start after [0001]-
[0048]
the setting
value x 1
hour(s)
Setting of the linked operation
with external devices
(Code: [4E])
No change
ON/OFF [0000]
linked
ON linked [0001]
OFF linked [0002]
Changing the ventilation mode
(Code: [EA])
No change
[0002]
Heat
exchange
mode
[0003]
Automatic
mode
Compatible with RBC-AMT32E
Changing the ventilation FAN
speed
(Code: [EB])
No change
High [0002]
Low [0003]
Imbalance [0004]
* "High" may be "Extra High".
Compatible with RBC-AMT32E
EN
60-EN