Page 1
Automatic Lift Fryer MODELS BLF-F, & BLF-FC Service Manual Serial Numbers 121836 and higher...
Page 2
All labor necessary to repair or replace factory defective parts will be performed, without charge, to the end user, by service personnel of a BKI Authorized Distributor during the first ninety days after the date of installation of the new equipment.
PERFECTION IN FRYING! The BKI name and trademark on this unit assures you of the finest in design and engineering -- that it has been built with care and dedication -- using the best materials available. Attention to the operating instructions regarding proper installation, operation, and maintenance will result in long lasting dependability to insure the highest profitable return on your investment.
Automatic Lift Fryer Introduction Safe Work Practices Keep The Casters Locked To avoid spilling shortening, keep the casters locked. If any shortening spills near your fryer, clean it up immediately. Noncombustible Floors Only Make sure your floor is noncombustible. Do not operate your fryer on floors that are wood, carpeted or have rubber mats.
Page 6
If you lose or damage your mitts, you can buy new ones at your local restaurant equipment supply store or from your local BKI Distributor. Always wear non-skid shoes when working around the fryer or any other equipment that uses shortening. Never wear loose clothing such as neckties or scarves while operating your fryer.
Page 7
Automatic Lift Fryer Introduction Keep this manual with the Equipment This manual is an important part of your equipment. Always keep it near for easy access. If you need to replace this manual, contact: Technical Services Department P.O. Box 80400 Simpsonville, S.C.
Page 8
Automatic Lift Fryer Introduction Be Prepared for Emergencies Be prepared for fires, injuries, or other emergencies. Keep a first aid kit and a fire extinguisher near the equipment. You must use a 40-pound Type BC fire extinguisher and keep it within 25 feet of your equipment.
National Electrical Code, ANSI NFPA 70-20XX. This unit, when installed by an authorized BKI service agent, must be wired for use in accordance with all applicable local, state, and federal codes. For specific electrical requirements and connections refer to the...
Automatic Lift Fryer Installation Initial Test and Adjustment 1. Fill pot with shortening to about one inch below the mark. Use only high-quality shortening that has low moisture content, a high smoke point and no additives. Overfilling the fryer pot with shortening could lead to serious injury. Ensure that the fryer pot is filled with shortening only to the fill mark when shortening is hot.
Use the information in this section to identify replacement parts. To order replacement parts, call your local BKI sales and service representative. Before calling, please note the serial number, model number and voltage on the rating tag affixed to the unit.
Page 13
Automatic Lift Fryer Replacement Parts Figure 1. Door Assembly Table 1. Door Assembly Parts ITEM # PART # DESCRIPTION F0083 THREAD INSERT 10-24 STEEL H0010 HINGE, LH PIN HALF N0165 DECAL, NOTICE LOST MANUAL N0175 DECAL, SLIPPING ADMONITIONS N0176 DECAL, INSTR & SAFETY MANUAL N0527 DECAL, SAFETY INSTR FRYERS P0022...
Page 24
Automatic Lift Fryer Replacement Parts Figure 10. Terminal Block Assembly Table 10. Terminal Block Assembly Parts ITEM # PART # DESCRIPTION TB0044-N TERM BLOCK TAGS "N" TB0049 TERM BLOCK 2 POLE JUMPER TB0048 TERM BLOCK GROUND BLOCK TB0047 TERM BLOCK END PLATE WAP TB0046 TERM BLOCK, WDU10 #102030 TB0044-G...
Refer to the table below to find the wiring diagram associated with your unit. Wiring Diagram Figure # Page # Domestic BLF-F 208V/220V/240V Figure 14 European BLF-F 220V/380V, 230V/400V, 240V/415V Figure 15 Domestic BLF-FC 208V/220V/240V Figure 16 European BLF-FC 220V/380V, 230V/400V, 240V/415V Figure 17...