Sony STR-DA5300ES Service Manual page 28

STR-DA5300ES
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT],
[MUSIC], [MOVIE] button in order, the message "MENU SPECIALIZED!" appears.
2. Press the button of the remote commander, the message "<<< SPECIAL >>>" appears.
M m
3. Press the button of the remote commander, the item is appears.
,
4. Each time the button of the remote commander is pressed, the item is switched in order as follows.
M m
Some items can change the content. Display the cursor by pressing the
by pressing the button of the remote commander, and fix the content by pressing the
M m
you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in
order again, the message "MENU SPECIALIZED OFF" appears.
Items
Video factory menu
Video calibration
(Video factory menu)
DDR access check
(Video factory menu)
Auto cal mic test
FL display fonts test
FL display test
HDCP key read
DSP SRAM check
FAROUDJA update
Model version display
Video Ucom version display
FAROUDJA version display
GUI CG-ROM version display
DSP Ucom version display
DSP serial flash version display
DSP parallel flash version display
DSP halt
DSP RAM
28
Display
<VIDEO FACTORY MENU>
V.CALIBRATION START?
DDR CHECK [XX] sec
SPEAKER OUT [XXXXX]
FL FONT [0x ** = X]
ALL ON
HDCP KEY READ [XXX]
<DSP SRAM CHECK>
[ENTER] button of the remote
r
commander
SRAM1 [XX] SRAM2 [XX]
FAROUDJA UPDATE [XXX]
##### *** vX. XX @@@@
Video Ucom Ver X. XX
FAROUDJA Ver X. XX
GUI CGROM Ver X. XX
DSP Ucom Ver X. XX
DSP SFLASH Ver X. XX
DSP PFLASH Ver X. XX
DSP HALT [XXX]
[*****]=XXXXXXXX
button of the remote commander, and changing the content
,
<
Remark
Menu mode to enter video calibration menu and DDR access check menu
If the [ENTER] button of the remote commander is pressed, entering the
menu, and operating two the following menu become possible
Procedure:
1. "DVD" is selected by using [INPUT SELECTOR] dial.
2. Connect a color pattern generator to the COMPONENT VIDEO
ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) on the A-
VIDEO board, DVD/BD VIDEO IN jack (J6201) on the A-VIDEO
board, DVD/BD S VIDEO IN jack (J6901) on the S-VIDEO board and
EXT VIDEO IN jack (J6904).
3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by automatic
operation in pressing the [ENTER] button of the remote commander, and
corrects reference value.
In a measurement once, only one of NTSC/PAL/HD can be measured
"Check XXXX V-IN" at display:
Video signal necessary for the measurement while measuring it last time
was not detected and it became an error
Confirm the input of the video of the terminal connection etc. , and
measure the [ENTER] button of the remote commander again pressing
XX: Time to do access check on DDR (for design evaluation)
XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from
speaker
**: 20 to FE, X: character
Each time DISPLAY button to change as follows
all on t test pattern 1 t test pattern 2 t all off t all on
XXX: ON or OFF
XX: OK or NG
OK: success access SRAM, NG: fail access to SRAM
XXX: ON or OFF
#####: Model
***: Destination
X.XX: System controller software version
@@@@: Sum value of flash memory in the system controller
X.XX: Video system controller software version
X.XX: Video Processor software version
X.XX: CG-ROM software version
X.XX: DSP controller version
X.XX: Serial flash software version
X.XX: DSP parallel flash version
XXX: ON or OFF
Mode that refers to internal RAM of DSP (for design evaluation)
button of the remote commander when