Clemas & Co TENNANT T2 Operator's Manual
  1. Manuals
  2. Brands
  3. Clemas & Co Manuals
  4. Scrubber
  5. TENNANT T2
  6. Operator's manual

Clemas & Co TENNANT T2 Operator's Manual

Scrubber dryer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TENNANT T2
SCRUBBER DRYER
OPERATOR MANUAL
Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury,
Gloucestershire, GL20 8NB.
Tel: 01684 850777
Fax: 01684 850707
Email:
info@clemas.co.uk
Web:
www.clemas.co.uk

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TENNANT T2 and is the answer not in the manual?

Questions and answers

Related Manuals for Clemas & Co TENNANT T2

Summary of Contents for Clemas & Co TENNANT T2

  • Page 1 TENNANT T2 SCRUBBER DRYER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.uk...

  • Page 2: Table Of Contents

    P.O. Box 6 5400 AA Uden- -The Netherlands europe@tennantco.com www.tennantco.com Specifications and parts are subject to change without notice. Original instructions, copyright E2008 Tennant Company. All rights reserved. Printed in the Netherlands. Tennant T2 (07- -08) Home Find... Go To..

  • Page 3: Safety Precautions

    In an area where flammable liquids/vapors Put scrub head in the lowered position. or combustible dusts are present. Set parking brake if equipped. Unless trained and authorized. Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 4: Safety Labels

    Located at bottom side of recovery tank. Power Before Working On Machine. WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks And Open Flame Away. Keep Battery Compartment Open When Charging. Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 5: Machine Components

    28. Battery Compartment MACHINE OPERATION SYMBOLS 2% (1°) Maximum Battery Discharge Main Power Grade Level Indicator I/O Key Switch Solution Flow Brush Motor Parking Brake Control Circuit Breaker (option) Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 6: Machine Installation

    1. Park the machine on a level surface and remove the key. 2. Carefully install the batteries into the battery compartment as shown (Figure 1). 3. Connect the battery cables as shown (Figure 1). Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 7: How The Machine Works

    Used for stripping of floor finish to prepare the floor for recoating. Heavy Duty Stripping Pad (Black) - - Used for aggressive stripping of heavy finishes/sealers, or very heavy duty scrubbing. FIG. 4 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 8 4. Turn the brush motor hub until the slot with the spring clip is visible through the scrub head window (Figure 10). FIG. 7 Spring Clip FIG. 10 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 9 Loosen the control console height adjustment knob and lift or lower the console to a comfortable operating height. Tighten knob to lock in position (Figure 15). FIG. 13 FIG. 15 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 10: Machine Operation

    17). The vacuum motor will automatically turn on. FIG. 20 6. To stop scrubbing, release the triggers, raise the scrub head and the squeegee and turn the key to the off position. FIG. 17 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 11 (Figure 21). If the red light appears, the scrubbing function will shut off automatically. This protects the batteries from total discharge. Recharge the batteries immediately. FIG. 23 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 12: Draining Tanks

    NOTE: When using a bucket to drain the machine, do not use the same bucket to fill the solution tank. 2. Open the recovery tank cover and rinse out the tank (Figure 25). FIG. 27 FIG. 25 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 13: Charging Batteries

    2. Park the machine on a flat, dry surface and turn the key off. 3. If charging wet (lead acid) batteries check the fluid level before charging (See BATTERY MAINTENANCE). Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 14 Contact Service Center Internal short circuit -- blown output fuse Replace battery charger Red Light Flashing Safety timer exceeded maximum charging Repeat charging cycle. If error repeats, time replace batteries Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 15: Machine Maintenance

    FIG. 35 3. Remove and clean the float shut--off screen located in the recovery tank (Figure 36). FIG. 39 FIG. 36 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 16 (See BATTERY MAINTENANCE). 3. Check for loose battery cable connections. 4. Inspect and clean the recovery tank cover seal (Figure 45). Replace if damaged. FIG. 42 FIG. 45 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..
  • Page 17 Open Flame Away. Keep Battery Compartment Open When Charging. 2. Clean the batteries to prevent battery corrosion. Use a scrub brush with a mixture of baking soda and water (Figure 50). FIG. 47 Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 18: Transporting Machine

    4. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 5. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 19: Troubleshooting

    Recharge batteries. Short run time Batteries not fully charged Fully recharge batteries Defective batteries Replace battery Service batteries See BATTERY MAINTENANCE Faulty battery charger Repair or replace battery charger Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

  • Page 20: Machine Specifications

    * Measured A- -weighted emission sound pressure level, per ISO 11201, in accordance with ISO 4871. Uncertainty value is 2 decibels. MACHINE DIMENSIONS 486mm 1093 mm 1128 mm 763 mm Tennant T2 (07- -08) Home Find... Go To.. Home Find... Go To..

Table of Contents