Page 1
Service SA12 / F1N, /N1G, /S1G, /U1B Manual Super Audio CD Player SUPER AUDIO CD PLAYER SA-12S1 VIDEO DISPLAY PLAY STOP PAUSE SOUND MODE REPEAT STANDBY POWER OPEN/CLOSE TABLE OF CONTENTS SECTION PAGE 1. Technical specifi cations ......................... 1 2. Warnings and laser safety......................3 3.
Page 2
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
Page 3
1. Technical specifi cations SACD/CD Audio characteristics Super Audio CD Channels 6 channels (Max.) 2 channels Frequency range 2 Hz - 100 kHz 2 Hz - 20 kHz Frequency characteristics 2 Hz - 50 kHz (-3 dB) 2 Hz - 20 kHz Dynamic range 114 dB more than 100 dB...
Page 4
SCART CONNECTOR SCART II (connected to TV) Pin signals: 1 Output Audio R 1.8 Vrms 2 Input Audio R 3 Output Audio L 1.8 Vrms Audio GND Blue/Chroma GND 6 Input Audio L 7 Bi-dir Blue out/Chroma in 0.7 Vpp +/- 0.1 V into 75 Ohm (*) 8 Output Function switch <...
Page 5
Warnings and laser safety Warning and laser safety WARNING WAARSCHUWING All ICs and many other semi-conductors are Alle IC’s en vele andere halfgeleiders zijn susceptible to electrostatic discharges (ESD). gevoelig voor elektrostatische ontladingen Careless handling during repair can reduce (ESD). life drastically.
Page 6
2.2 LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. LASER DEVICE UNIT Type: Semiconductor laser GaAlAs Wave length: 650 nm (DVD) 780 nm (VCD/CD) Output Power: 7 mW (DVD)
Service hints, Taking the disc out DAC PCB Service hints 3.1.1 Switched Mode Power Supply Unit PZ03 This power supply unit is not repairable and must be exchanged completely in case of failure. A new power supply can be ordered with codenumber QW12922150 (3104 129 22150).
Page 8
3.1.4. Mechanical- and dismantling instructions...
Page 9
3.2 Taking the disc out. 1. Remove the top cover with 8 screws. 2. Remove the both side covers with 8 screws. 3. Remove the 8 screws of front panel and unfasten 2 screws of front legs. 4. Pull out the front panel. 5.
Page 10
How to confi rm the software and the version. 11111111.008/ 22222222.008: Displayed on TV screen as background of marantz is OK, after entering version. If a power supply is turned on, with <STOP> and <NEXT> of a player pushed, a change of NTSC mode and PAL mode can be performed.
Page 11
English English English Japanese Español Español Español English Français Français Français Español Português Português Português Français Italiano Italiano Russian Português Deutsch Russian Japanese Russian Nederlands Deutsch Korean Korean Suomeksi Greek Chinese Chinese Dansk Japanese Bahamas Indonesia Bahamas Indonesia Norsk Korean Khmer Khmer Svenska...
Page 12
Diagnostic software, trouble shooting and test instructions Due to the complexity of the SACD player, the time to find a PLAYER SCRIPT INTERFACE defect in the player can become long. To reduce this time, the player has been equipped with Diagnostic and Service 5.2.1 Description software (DS).
Page 13
Step Description Executing nucleus Press OPEN/CLOSE and STOP, and turn on the player. Display shows "FP SEGMENT". Press PLAY to execute this nucleus. Otherwise press NEXT and go to step 7. 502 Starbursts are visible. Press PLAY. Horizontal bars are visible. Press PLAY. Vertical bars are visible.
Page 14
RC KEY CODE RC KEY NAME TV POWER ONLY FOR TV SACD POWER STOP SOUND MODE PLAY REVERSE PAUSE SLOW FORWARD PREVIOUS RESUME NEXT MENU DISC MENU SYSTEM LEFT RIGHT DOWN RETURN ZOOM ANGLE SHUFFLE SUBTITLE AUDIO DISPLAY REPEAT A-B SCAN VOL + ONLY FOR TV...
Page 16
5.2.3 Errorlog Error Error name Explanation Number Explanation: 0109 S2B_SBC_NO Requested subcode item could The application errors will be logged in the NVRAM. The T_FOUND not be found. maximum number of error bytes that will be visible is 16. The 010A S2B_TRAY Tray could not be opened or...
Page 17
SMA error codes Error Error name Explanation Number 0000 SMA_TIMEO Data coming from disc not in UTERROR time. Reason: damaged disc or engine problem. 5.2.4 Reprogramming of region code Caution This information is confidential and may not be distributed. Only a qualified service person should reprogram the mono board.
Page 18
5.3.2 ERROR HANDLING Host Decoder Tests [01] [xx yy] Nuclei Each nucleus returns an error code. This code contains six Number numerals, which means: Checksum Flash Checks the FLASH checksum. Flash Write Access 1 Checks whether the first [ XX YY ZZ ] FLASH can be written.
Page 19
[xx yy] Nuclei [xx yy] Nuclei Number Number Pink Noise On Generates internally on the Line1 Lifetime Log Ends the lifetime log. The in- Sti5505 a pink noise audio signal that will be formation is displayed on the local display and is passed to all the DACs were it is converted to an send to the serial port.
Page 20
PLAY for confirming that the test is correct. PREV when the [xx yy] Nuclei test is not ok. NEXT is pressed in order to abort to the Number nucleus at any time; the nucleus is not tested successfully. 1202 Write Read Fast SDRam Low The following two The confirmation can also be send through the serial port for individual memory tests will be executed at the automated verification.
Page 21
Grooves Menu [xx yy] Nuclei 1. Inside of the Disc [612] Number 2. Middle of the Disc [613] 1410 Scart Low Steers pin 16 on the scart connector 3. Outside of the Disc [614] with the value low (0 to 2 V). 1411 Scart Medium Steers pin 16 on the scart connec- Laser Menu...
Page 22
→ Nuclei Error Codes 5. Pink Noise → 6. Sine Generate 7. Digital Board Version [108] In the following tables the error description of the error codes 8. Flash Checksum [100] will be described. 9. Flash1 Write Access [101] 10. Flash2 Write Access [102] 5.4.1 Host Decoder Nuclei...
Page 23
5.4.2 NVRAM Nuclei Error code Error description 11500 Test succeeded. 11501 Set-up of I2C failed. Error code Error description 11502 The selection of the clock source failed. 40000 Test succeeded. 11504 The demute of the audio failed. 40001 I2C access failed. 11600 Test succeeded.
Page 24
Error code Error description Error code Error description 50502 Test failed. 50504 Not all keys were pressed. 60900 Test succeeded. 60901 Basic Engine returned error number 0xXX. 50600 Test succeeded. 60902 Parity error from Basic Engine to Serial. 50601 I2C connection failed. 60903 Communication time-out error.
Page 26
Test instructions SACD mono board Error code Error description 131300 Test succeeded. 5.5.1 General 131301 I2C bus busy before start. 131302 I2C access failed. Impedance of measuring-equipment should be > 1MΩ Most tests have to be done by software commands. 131400 Test succeeded.
Page 27
5.5.3 Reset circuitry PM3394B Reset of Sti5505: ch1: freq= 16.9MHz In power down mode STB_CONT is high; the clock is disabled in order to reduce the power consumption. When STB_CONT goes low, STB_CONTD goes high and enables the 27 MHz clock. Check that this clock is present and stable before the RESETn is de-asserted.
Page 28
PM3394B PM3394B ch1: freq= 8.50MHz ch1: freq= 50.0MHz CH1 1.00 V~ MTB50.0ns ch1+ CH1 1.00 V~ MTB20.0ns ch1+ ST_CLK CL 06532152_020.eps CL 06532152_021.eps MACE CLK 051200 051200 Memories 5.5.5 Tests with diagnostic software program The SACD diagnostic program is included in the SACD Flashes application software.
Page 29
S2B bus The S2B is the interface between the digital part and the front PM3394B end. This bus links the STi5505 and the MACE2. The S2B ch1: freq= 24.6MHz echo command permits to check the communication between those devices. Ref.# Command Name Remark S2b Echo Write and read back...
Page 30
Signal Test type Level Frequency Signal Test type Level Frequency point point PCM_Ce_Lf_Fu F659 No signal LVTTL N/A PCM_LsRs_Fur F504 LVTTL N/A signal PCM_LsRs_Fur F504 No signal LVTTL N/A SPDIF F644 Data strea SPDIF F644 Data stream Press “STOP” to switch off the sine wave. PM3394B PM3394B ch1: freq= 2.79MHz...
Page 31
Ref.# Command Remark PM3394B Name Pink Noise ON Play the pink noise at the audio outputs Then measure the following signals Signal Test type Level Frequency point SCLK_AV F637 Clock LVTTL 3.072MHz < 0.02% LRCLK_AV F641 Clock LVTTL 48 kHz <...
Page 32
Chrominance C_VID Blue B_VID Measured at F665 Measured at F653 PM3394B PM3394B CH1 200mV~ MTB20.0us ch1+ CH1 200mV~ MTB20.0us ch1+ C_VID B_VID CL 06532152_033.eps CL 06532152_036.eps 051200 051200 Red R_VID Switch off the colour bar with the following command: Measured at F646 Ref.# Command Name Remark Value Colour bar Off...
Page 33
5.5.7 SERVO TESTS Signal Test type Level Frequency point General start-up measurements: DSD_PCM(1) F006 Signal : High LVTTL N/A DSD_PCM(4) F007 Data stream LVTTL N/A Reset the Basic Engine part DSD_PCM(5) F008 Signal : High LVTTL N/A DSD_PCM(2) F009 Data stream LVTTL N/A Ref.
Page 34
Disc Motor: Before switching on the disc motor, check the following test PM3394B points: Name Testpoint Value Stby F357 high Stby-out F355 Moto1 F361 3V±0.3 Switch the Discmotor on/off with next commands: Ref. # Command Name Remark BeDiscmotorOn Discmotor on BeDiscmotorOff Discmotor off Check the following signals when discmotor has been...
Page 35
Ref. # Command Remark PM3394B Name BeTrayIn Tray in BeTrayOut Tray out Measure the driver outputs of the BA5938FM for the tray closed. Name Testpoint Value Vo2 - F116 4.3V±2.0V Vo2 + F111 4.3V±2.0V Measure again the driver outputs while the tray is opening. Name Testpoint Value...
Page 36
PM3394B V filament Display V filament Key-matrix Buffer µProcessor Supply : RC-6 +5Vstby +12V RC-Eye -40V CH1 2.00 V~ MTB 500ns ch1+ CL 06532152_048.eps 051200 Figure 5-10 Check for laserlight. Functionality description: Switch the focus off The essential component of the display PCB is the uP (slave).
Page 37
Reset Key-matrix Check next reset timing with an oscilloscope at pin 10 of the Connect a extra 10k( pull-up to pin 36 en 37 of the uP and (processor. check next matrix scanning at these pins. PM3392A PM3392A ch1: low =-46.9mV ch1: high= 5.09 V STOP CH1 2.
Trouble shooting AV Board Testing of A/V board can be done using diagnostic software “Player script”. Mono board is used to generate a sound with the sound tests PINKNOISE ON and SINE ON. A VIDEO signal is generated with COLOUR-B ON. Functional control of scart switching is also possible.
Page 40
NO SOUND ON AUDIO CINCH 1402 TV- & AUX SCART To put set in “Player script”, press keys Diagnostic Software STOP+OPEN/CLOSE simultaneously and switch on. Proceed until display shows “ ”. SINE ON Press PLAY to execute test. Display shows " ".
Page 41
VIDEO PART NO PICTURE CVBS & Y/C OUT To put set in “Player script”, press keys STOP+OPEN/CLOSE simultaneously and switch mains on. Diagnostic Software Proceed until display shows “ ". COLOUR-B ON Press PLAY to execute. Check supply voltages +8Vstby, –8Vstby, +12Vstby, +6Vstby.
Page 42
PM3392A PM3392A 200mV~ MTB20.0us ch1+ 200mV~ MTB20.0us ch1+ TP 1 : video B TP 6 : Y_ENC PM3392A PM3392A 200mV~ MTB20.0us ch1+ 500mV~ MTB20.0us ch1+ TP 2 : video G TP 19 : CVBS_OUT PM3392A PM3392A 200mV~ MTB20.0us ch1+ 50mV~ MTB20.0us ch1+ TP 3 : video R...
Page 43
NO PICTURE SCART SCART SWITCHING To put set in “Player script”, press keys Diagnostic Software STOP+OPEN/CLOSE simultaneously and switch mains on. Proceed until display shows “ ". COLOUR-B ON Press PLAY to execute. Check RGB at testpoints 1-3 Check HSYNC at pin 14 of IC 7316 (testpoint 24). Check RGB at output of RGB video processor 7316 PICTURE TV? testpoints 25.
Page 44
Trouble shooting DAC Board TROUBLESHOOTING DAC BOARD Testing of DAC board can be done using diagnostic software “Player script”. Mono board is used to generate a sound with the sound test SINE ON. DAC''s & Filters To put set in “Player script”, press keys STOP+OPEN/CLOSE simultaneously and switch player on.
Page 45
Testing of I2C communication to DAC board can be done using diagnostic software. DAC BOARD I2C COMMUNICATION See MENU MODE INTERFACE to put set in DSW mode Diagnostic Software Select 2: Dac Board menu Internal : CLK SEL = H Clock Internal External: CLK SEL = L (0V) Clock External...
Page 90
8. Exploded view and Parts list 5 1 1 0 W 0 0 1 3 X 6 ( M) 5 4 0 5 0 0 5 Dx 8 3 ( M) 0 0 1 D 5 1 2 7 0 1 0 Dx 7 5 1 2 7 3 X 8 (M) 0 7 2 G...
Page 91
9965 000 10850 TERMINAL EW-2560T-LH-B YT02011300 SPEAR PARTS 001S PACKING CASE 413K801010 C-CH J653 9965 000 10850 TERMINAL EW-2560T-LH-B YT02011300 002S CUSHION 413K809010 LEE-CH 008S ACCESSORY BOX 413K801210 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 92
QT19400710 3139 194 00710 SUSPENSION (YELLOW) QT19400710 3139 194 00620 SUSPENSION (BLUE) QT19400620 3139 194 00620 SUSPENSION (BLUE) QT19400620 3139 197 60060 CLAMPER ASSY QT19760060 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 93
3139 198 80010 SWITCH, OTHERS QT19880010 4822 532 13097 RING, RUBBER QP53213097 3139 194 00270 TRAY, PLASTIC QT19400270 3139 197 50060 MOTOR ASSY DC <=37.5W QT19750060 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 94
Circuit-, IC descriptions and list of abbreviations SAA7399 (MACE2) General. • Sledge stepper motor support. Mace2 is a name used for the successor of the ACE1 IC. The The Digital Servo block. term MACE (mini-ACE) is used because MACE2 does not have a decoder on board.
Page 95
– Defect detector: Holds the focus and/or radial control correct the loop gain. Since this decreases the optimal signal on disc dropouts. performance, the gain control should only activated shortly – Speed control: Used during access. With radial actuator (for instance when starting a new disc). feed forward.
Page 96
In the sledge jump mode maximum power (user measured before the injection point. The injected signal is programmable) is applied to the sledge in the correct shaped by H/1+H . This measured signal is multiplied by a direction, while the actuator becomes idle. phase shifted version of the injected signal.
Page 97
9.14 Laser Low Power (LLP). The LLP output can be used by write-able systems to switch the laser back to read power when the light spot goes off- track while writing discs. To prevent that the neighbour tracks are damaged when the spot goes off-track the laser has to be switched very fast to the safe read power.
Page 98
in which the pattern recorded in the previous stage is read the input LPF's, the OPC pre-processor and the EFM back. detector. During this read phase the OPC block stores A1, A2 and The sequencer controls the timing of all the hardware actions CALF samples from exact the same location where during in the OPC hardware.
Page 99
DVDALAS2plus Advanced Analogue TZA1033 DVD Signal Processor and Laser Supply GENERAL DESCRIPTION FEATURES The DVDALAS2 is an analogue preprocessor and laser Operates with DVD-ROM,DVD-RAM, DVD+RW, supply circuit for DVD / CD read only players. The device DVD-RW, CD-ROM and CD-RW media contains data amplifiers, several options for radial tracking Operates up to 64x CD-ROM and 8x DVD-ROM and focus control.
Page 100
DVDALAS2plus Advanced Analogue DVD TZA1033 Signal Processor and Laser Supply DEVICE BLOCK DIAGRAM Diode Ampli?ers Balanced Processing Data & header Interface Header Land Servo Signals Push Pull Land/Groove D1-D6 Swap Offset Mute compensations 3 Beam Tracking V & I references Rext Dual Laser Supply...
Page 101
DVDALAS2plus Advanced Analogue DVD TZA1033 Signal Processor and Laser Supply PINNING Name Description CD-A CD pick up input A CD-B CD pick up input B CD-C CD pick up input C CD-D CD pick up input D CD-REF CD pick up reference voltage CD-E CD pick up input E CD-F...
Page 102
DVDALAS2plus Advanced Analogue DVD TZA1033 Signal Processor and Laser Supply Name Description SIDA Serial host interface data input SICL Serial host interface clock input SILD Serial host interface load VDDA1 Analog Supply voltage 1 (RF input) VDDA2 Analog Supply voltage 2 (RF internal) VDDA3 Analog Supply voltage 3 (RF output stage) VDDA4...
Page 104
BA6856FP: 3 PHASE MOTOR DRIVER FOR DVD PLAYERS Features /3-phase, full-wave pseudo linear driving system built-in power save built-in therma shut down circuit built-in current limit circuit built in Hall bias circuit built in FG-output (3-phase parallel output) with switching function of regular/ reverse rotations blockdiagram BA6856FB DRIVER...
Page 105
pin description PIN No PIN NAME DESCRIPTION N.C. Not connected N.C. Not connected Output 3 for motor N.C. Not connected Output 2 for motor N.C. Not connected Output 1 for motor Ground Hall input Amp1. positive input Hall input Amp1. negative input Hall input Amp2.
Page 106
SAA7335 DSP for CD and DVD-ROM systems FEATURES Compatibility with CD-I, CD-ROM, MPEG-video DVD-ROM and DVD-video applications Designed for very high playback speeds Typical CD-ROM operation up to n = 12, DVD-ROM to n = 1.9, maximum rates (tbf) In DVD modes double-pass C1-C2 error correction is used Matched filtering, quad-pass error correction which is capable of correcting up to 5 C1 frame errors and (C1-C2-C1-C2), overspeed audio playback function...
Page 107
SAA7335 DSP for CD and DVD-ROM systems ORDERING INFORMATION PACKAGE TYPE NUMBER NAME DESCRIPTION VERSION SAA7335GP LQFP100 plastic low profile quad flat package; 100 leads; body 14 x 14 x 1.4 mm SOT407-1 BLOCK DIAGRAM handbook, full pagewidth SRAM 32 KBYTES DEMODULATOR PLL BIT HF input...
Page 108
SAA7335 DSP for CD and DVD-ROM systems PINNING SYMBOL TYPE DESCRIPTION supply analog ground 1 SSA1 analog current reference input for ADC REFLo analog low reference input for ADC REFHi analog high reference input for ADC VREF analog negative input HFIN analog positive input supply...
Page 109
SAA7335 DSP for CD and DVD-ROM systems SYMBOL TYPE DESCRIPTION sub-CPU data bus bit 1 input/output (parallel) − n.c. not connected, reserved sub-CPU data bus bit 0 input/output (parallel) supply digital supply voltage 4 DDD4 supply digital ground 4 SSD4 sub-CPU write enable input (active LOW) sub-CPU read enable input (active LOW) sub-CPU address latch enable input...
Page 110
SAA7335 DSP for CD and DVD-ROM systems SYMBOL TYPE DESCRIPTION supply digital ground 7 SSD7 RAMAD7 RAM address bit 7 output RAMAD8 RAM address bit 8 output RAMAD9 RAM address bit 9 output − n.c. not connected, reserved RAMAD10 RAM address bit 10 output RAMAD11 RAM address bit 11 output RAMAD12...
Page 111
SAA7335 DSP for CD and DVD-ROM systems handbook, full pagewidth V SSA1 RAMAD1 I ref RAMAD0 REFLo V SSD6 REFHi V DDD6 VREF RAMDA0 HFIN RAMDA1 V SSA2 n.c. AGCOUT RAMDA2 V DDA2 RAMDA3 V DDD1 RAMDA4 V SSD1 RAMDA5 RAMDA6 SAA7335 MOTO1...
Page 112
SAA7335 DSP for CD and DVD-ROM systems 1. The coincidence counter: this is used to detect the FUNCTIONAL DESCRIPTION coincidence of successive syncs. It generates a sync Analog front-end coincidence signal if 2 syncs are 588 ±1 EFM clocks apart. This block converts the HF input to the digital domain using an 8-bit ADC proceeded by an AGC circuit to obtain the 2.
Page 113
SAA7335 DSP for CD and DVD-ROM systems The sequence for a write data command (1 data byte) is as Microcontroller interface follows: The SAA7335 has two microcontroller interfaces, one Send START condition serial I C-bus and one parallel (8051 microcontroller compatible).
Page 114
Am29LV160BT/Am29LV160BB 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Sector Erase Flash Memory DISTINCTIVE CHARACTERISTICS Single power supply operation Top or bottom boot block configurations available — Full voltage range: 2.7 to 3.6 volt read and write operations for battery-powered applications Embedded Algorithms —...
GENERAL DESCRIPTION The Am29LV160B is a 16 Mbit, 3.0 Volt-only Flash The host system can detect whether a program or memory organized as 2,097,152 bytes or 1,048,576 erase operation is complete by observing the RY/BY# words. The device is offered in 48-ball FBGA, 48-ball pin, or by reading the DQ7 (Data# Polling) and DQ6 BGA, 44-pin SO, and 48-pin TSOP packages.
PRODUCT SELECTOR GUIDE Family Part Number Am29LV160B Ordering Part Number: =3.0–3.6 V = 2.7–3.6 V Max access time, ns (t Max CE# access time, ns (t Max OE# access time, ns (t Note: See “AC Characteristics” for full specifications. BLOCK DIAGRAM –...
Page 118
MT48LC1M16A1 S - 512K x 16 x 2 banks SYNCHRONOUS DRAM FEATURES PIN ASSIGNMENT (Top View) • PC100 functionality • Fully synchronous; all signals registered on positive 50-Pin TSOP edge of system clock • Internal pipelined operation; column address can be changed every clock cycle DQ15 •...
Page 119
16Mb: x16 SDRAM GENERAL DESCRIPTION (continued) sequence. Accesses begin with the registration of an AC- but it also allows the column address to be changed on every TIVE command, which is then followed by a READ or clock cycle to achieve a high-speed, fully random access. WRITE command.
Page 120
16Mb: x16 SDRAM FUNCTIONAL BLOCK DIAGRAM 1 Meg x 16 SDRAM BANK0 ROW- MEMORY ADDRESS 2,048 ARRAY LATCH (2,048 x 256 x 16) DQML, DQMH 256 (x16) CONTROL LOGIC CAS# SENSE AMPLIFIERS RAS# I/O GATING DQM MASK LOGIC DATA OUTPUT MODE REGISTER REGISTER DQ0-...
Page 121
16Mb: x16 SDRAM PIN DESCRIPTIONS Input Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on the positive edge of CLK. CLK also increments the internal burst counter and controls the output registers. Input Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal. Deactivating the clock provides PRECHARGE POWER-DOWN and SELF REFRESH operations (all banks idle), ACTIVE POWER-DOWN (row ACTIVE in either bank) or CLOCK SUSPEND operation (burst/access in progress).
Page 122
STi5505 (Rev. Ax) DVD BACKEND DECODER WITH INTEGRATED HOST PROCESSOR PRODUCT PREVIEW INTEGRATED 32-BIT RISC HOST CPU DESCRIPTION The STi5505 provides a very highly integrated back- - 2KBYTES INSTRUCTION CACHE, 2KBYTES DATA CACHE/SRAM end solution for DVD and combo DVD-DVB (Set Top Box) applications.
Page 123
STi5505 (Rev. Ax) I - GENERAL DESCRIPTION The performance offered by the ST20 CPU and its width/memory size compromise. associated hardware (decoders, encoder, periphe- The algorithm is lossless and uses "on-the-fly" rals...) allows an integrated and unified DVD or decoding to reduce the memory requirements to DVD-DVB software solution.
Page 124
STi5505 (Rev. Ax) I - GENERAL DESCRIPTION (continued) The encoder handles interlaced and non-interlaced The main features of the decoder core are : mode. - Decodes 5.1 Dolby AC-3 Digital surround, It can perform Closed Captions, CGMS or Teletext - Output to 6 channels. Downmix modes : 1, 2, 3 encoding and allows Macrovision 7.01/6.1 copy or 4 channels for MPEG and AC-3 streams, protection.
Page 125
STi5505 (Rev. Ax) I - GENERAL DESCRIPTION (continued) allows to transfer packets between the Set Top Box The main features of the DVD interface are : and external units, either for recording or playback - DVD, VCD and CD-DA compatible, purposes.
Page 127
STi5505 (Rev. Ax) II - PIN DESCRIPTION (continued) II.2 - Pin List Name Type Function SUPPLIES 1, 18, 34, 67, 75, 86, 95, Power Supply 102, 110, 119, 130, 139, 149, 159, 171, 184, 208 4, 19, 35, 68, 77, 87, 96, Ground 103, 111, 120, 131, 140, 150, 160, 172, 185, 200...
Page 128
STi5505 (Rev. Ax) II - PIN DESCRIPTION (continued) II.2 - Pin List (continued) Name Type Function EXTERNAL INTERRUPTS 23, 25 IRQ[0:1] External Interrupts PROGRAMMABLE I/O AND ALTERNATE FUNCTION (see Device Configuration Chapter) PIO0 [0] General Purpose I/O or PARA_SYNC (DVD//Front End) or Sc1Data (Smart Card 1 Data I/O) PIO0 [3] General Purpose I/O or PARA_REQ (DVD//Front End)
Page 129
STi5505 (Rev. Ax) II - PIN DESCRIPTION (continued) II.2 - Pin List (continued) Name Type Function SDRAM INTERFACE 78-81, 69, 70-74, 82, 83 AD[0:11] SDRAM Address Bus 92-94, 97-101, 106-109, DQ[0:15] SDRAM Data (Lower Byte) 112-115 84, 85 SDCS[0:1] SDRAM Chip Selects SDCAS SDRAM CAS SDRAS...
Page 130
STi5505 (Rev. Ax) III - FUNCTIONAL DESCRIPTION High memory bandwidths up to 200 Mbytes/s can III.1 - Functional Modules be supported by the SDRAM EMI. Figure 1 shows the subsystem modules that make up the STi5505. These modules are outlined below. The STi5505 internal memory interconnect pro- vides buffering and arbitration of memory access requests to sustain very high throughput of memory...
Page 131
STi5505 (Rev. Ax) III - FUNCTIONAL DESCRIPTION (continued) and allows Macrovision The block also handles overspeed processing for 7.01/6.1 copy protection. all systems. The capturing of CD-DA sectors is based on a flywheel tiner to improve robusters by III.11 - MPEG-2 Audio / Dolby AC-3 Decoder concealing erros in the subcode stream.
Page 132
ST24E32 ST25E32 32K SERIAL I C EEPROM with EXTENDED ADDRESSING NOT FOR NEW DESIGN COMPATIBLE with I C EXTENDED ADDRESSING TWO WIRE SERIAL INTERFACE, SUPPORTS 400kHz PROTOCOL 1 MILLION ERASE/WRITE CYCLES, OVER the FULL SUPPLY VOLTAGE RANGE 40 YEARS DATA RETENTION SINGLE SUPPLY VOLTAGE ±...
Page 133
ST24E32, ST25E32 Figure 2A. DIP Pin Connections Figure 2B. SO Pin Connections ST24E32 ST24E32 ST25E32 ST25E32 V CC V CC V SS V SS AI01202B AI01203C Table 2. Absolute Maximum Ratings Symbol Parameter Value Unit °C Ambient Operating Temperature ±40 to 125 °C Storage Temperature ±65 to 150...
Page 134
9.24 Description of Furore IC 9.24.1 General Description FURORE-IC is a one-chip design containing all the hardware required for SACD processing. It is intended to interface to the Sti family (Sti5505/Sti5508) DVD video decoders. The FURORE-IC contains a memory interface to support one 4M*16 SDRAM or one 1M*16 SDRAM device.
Page 135
RESETn is an asynchronous reset and should be low for at 9.24.6 Pin description least 1 period of DSD_CLK. General-purpose in/outputs. Four general purpose input and output signals are available. IC-Pin_no Name Type Function H_DQ[13] I/O5 Data bus H_DQ[12] I/O5 Data bus VCC_IO 3.3V power supply IO...
Page 136
IC-Pin_no Name Type Function adcrefl APIO ADC decoupling low. (via 100nF to VSS) vssrefadc VSSCO VSS of Reference Ladder of ADC ( not to the substrate) PCM_LeRi_in PCM data Left/Right PCM_CeLf_in PCM data Centre/LFE PCM_LsRs_in PCM data lift/Right surround PCM_wclk_in PCM word clock PCM_dclk_in PCM data clock...
Page 137
IC-Pin_no Name Type Function DSD_PCM_0 DSD data output signal. On 64 * Fs Stereo : Left channel (channel 0) MCA5/6 : front left ( channel 0) OR From PCM switch matrix DSD_PCM_1 Stereo : right channel (channel 1) MCA 5/6 : front right ( channel 1) OR From PCM switch matrix DSD_PCM_2 Stereo...
Page 138
IC-Pin_no Name Type Function GND_CORE Ground(core) PCM_dclk_Out PCM data clock Tst(1) internal pull up for both test pins Tst(0) IC testpins tst(1:0) 11 : Functional behaviour 10 : RAM test 01 : scan shift 00 : scan normal Boundary scan Data Input. Boundary scan Mode select Boundary scan Clock O10put...
Page 139
DISCS Filter switch position Position 1 position 2 position 3 SACD (DSD) All channels: Normal* L and R: Custom* Other channels: Normal All channels: Custom CD (PCM) All channels : Custom * Normal: output via 1 filter stage (3rd order filter) Custom: output via 2 filter stage (6th order filter) 9.25.3 Description of DAC CS4397 CS4397...
Page 140
Pin Function Pin Name Description Reset input (Low active) M4(AD0/CS) Chip address bit0 for I2C M3(AD1/CDIN) Chip address bit1 for I2C M2(SCL/CCLK)) Serial clock for I2C M0(SDA/CDOUT) Serial data for I2C DGND Digital ground Digital power supply +3.3V Digital power supply +3.3V DGND Digital ground MCLK...
Page 141
9.25.4 Description of I2C controller PC8574 PC8574 Block Diagram Pin Configuration V DD INTERRUPT LP FILTER LOGIC PCF8574 PCF8574 INPUT I C BUS FILTER CONTROL SHIFT 8 BIT REGISTER PORT V SS WRITE pulse READ pulse V DD POWER-ON V SS RESET Pin Function SYMBOL...
Page 142
9.26 IC description of Linear power supply PQ15RW11 Pin Configuration PQ15RW11 1 DC input(Vin) 2 DC output(Vo) 3 GND 4 Output voltage adjustment terminal(Vadj) Block Diagram Input Output Specific IC Output voltage adjustment terminal TA7317P CL 06532152_102.eps 131200...
Page 143
9.27 List of abbreviations CALF_MACE Central aperture low frequency control signal to MACE CAS[1:0]ND DRAM column address strobe +12VSTBY +12V power supply present during CASN SDRAM column address strobe standby CE_ROM1N Chip enable flash eprom IC7401 Filtered 3V3 power supply to CE_ROM2N Chip enable flash eprom IC7451 IC7207(MACE servo processor)
Page 144
HPSW Control signal to swith HF signal RASN SDRAM row address strobe path Read enable input of HD61 HSYNC Horizontal synchronization output REFCOS Position Control Sledge external I2C_DAC Control signal to enable/disable the cosine offset compensation/stepper I2C bus to the DAC PCB motor cosine output Interrupt request REFSIN...
Page 145
TRAY2 Tray motor control signal 2 from servo processor to power driver TRAYSW Tray switch control signal to servo processor TRST Boundary scan test port reset TXD_BE Transmitted data basic engine serial interface (S2B) TXD_SER Transmitted data service serial interface VCC_FUR Filtered power supply 3V3 to FURORE IC...
10. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : ASSIGNMENT OF COMMON PARTS CODES. RESISTORS The suppliers and their type numbers of fusible resistors : 1) GD05 × × × 140, Carbon film fixed resistor, ±5% 1/4W are as follows; : 2) GD05 ×...
Page 147
4822 122 33777 47pF 5%NP0 63V QP12233777 2300 4822 126 14305 100nF 10% X7R 16V 0603 CER QP12614305 2533 4822 122 33777 47pF 5%NP0 63V QP12233777 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 148
4822 051 30471 470R00 5% 0.062W QP05130471 2821 4822 126 14305 100nF 10% X7R 16V 0603 CER QP12614305 3123 4822 051 30103 10k00 5% 0.062W QP05130103 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 149
QP05130331 3326 4822 051 30479 47R00 5% 0.062W QP05130479 3205 4822 051 30103 10k00 5% 0.062W QP05130103 3327 4822 051 30682 6k80 5% 0.062W QP05130682 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 150
3903 4822 051 30339 33R00 5% 0.062W QP05130339 3608 4822 117 13632 100k 1% 0603 0.62W QP11713632 3904 4822 051 30339 33R00 5% 0.062W QP05130339 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 151
9322 144 59668 IC SM MT48LC1M16A1TG-7S QA14459668 5900 4822 157 11717 BLM31P500SPT QP15711717 7452 4822 130 60511 BC847B QP13060511 5901 4822 157 11717 BLM31P500SPT QP15711717 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 152
4822 051 20471 470R00 5% 0.1W QP05120471 2412 N 4822 124 40433 47µF 20% 25V QP12440433 3333 N 4822 117 10353 150R 1% 0.1W QP11710353 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 153
4822 051 20472 4k70 5% 0.1W QP05120472 3436 N 4822 117 10353 150R 1% 0.1W QP11710353 3612 N 4822 117 10833 10k 1% 0.1W QP11710833 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 154
3003 F,U,S 4822 051 20008 0R00 JUMP. (0805) QP05120008 7402 N 4822 130 42804 BC817-25 QP13042804 3004 F,U,S 4822 051 20008 0R00 JUMP. (0805) QP05120008 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 155
4822 117 10833 10k 1% 0.1W QP11710833 7018 F,U,S 4822 130 60511 BC847B QP13060511 3117 F,U,S 4822 117 10833 10k 1% 0.1W QP11710833 7019 F,U,S 4822 130 60511 BC847B QP13060511 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 156
4822 242 10756 DSS306-92Y5S221M100 QP24210756 5007 F,U,S 4822 242 10756 DSS306-92Y5S221M100 QP24210756 SWITCHED MODE POWER SUPPLY UNIT (PZ03) PZ03 3104 129 22150 POWER SUPPLY UNIT QW12922150 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 157
9965 000 06703 CHIP 1.2k ±1% 1/10W NI01122110 F821 4822 070 38001 FUSE T800mA 250V FS10080850 R804 9965 000 06704 CHIP 2.2k ±1% 1/10W NI01222110 BS LISTED NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 158
4822 124 90051 ELECT. 220µF M 25 V ARA OA22702550 C212 N 4822 124 80123 ELECT. 220µF 16V ARS OA22701640 C212 S 4822 124 80123 ELECT. 220µF 16V ARS OA22701640 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 159
9965 000 10845 FILM 1800pF J 100V NH OF15182550 C517 U FILM 560pF ±5% 100V OF55561540 C701 S 9965 000 10845 FILM 1800pF J 100V NH OF15182550 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 160
4822 051 20228 CHIP 2.2Ω ±5% 1/10W NI05022110 CD46 U 9965 000 01567 ELECT. 100µF 10V ARA OA10701050 R158 4822 051 20228 CHIP 2.2Ω ±5% 1/10W NI05022110 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 161
4822 051 30102 CHIP 1kΩ ±5% 1/16W NN05102610 R511 4822 051 20102 CHIP 1kΩ ±5% 1/10W NI05102110 RD51 4822 116 82487 CHIP 0Ω ±5% 1/16W NN05000610 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 162
4822 130 32362 DIODE 1SS176 MA165 1SS254 HD20002000 Q404 4822 130 63928 CHIP TRS. 2SA1312 B HX113121B0 30V 0.1A Q405 4822 130 63929 CHIP TRS. 2SC3324 B HX333241B0 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 163
RY43 4822 051 30121 CHIP 120Ω ±5% 1/16W NN05121610 CHIP 10kΩ ±5% 1/16W NN05103610 L622 9965 000 06669 RELAY ED2-12NU LY20120620 RY45 4822 051 30103 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 164
4822 130 80326 L.E.D. LT3D8B RED 3O HI10062320 RY44 4822 051 30121 CHIP 120Ω ±5% 1/16W NN05121610 SY40 9965 000 10847 PUSH SW. SPPH430100 SP02022310 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.