Wireless Remote Control; Operating Range For The Remote Control; Handling The Remote Control - NEC MultiSync LCD5710 User Manual

Wireless Remote Control

1
POWER button
Switches the power on/off.
* If Power Indicator is not glowing, then no controls will work.
2
INPUT button
Selects from input signal, [RGB1], [RGB2], [RGB3], [DVD/HD],
[VIDEO] or [VIDEO<S>].
[VIDEO<S>] is enabled by selecting the "SEPARATE" mode in the
OSM or by having the "S-VIDEO" cable connected with the
"S-VIDEO" signal present and selecting "PRIORITY" MODE.
See page 24.
3
AUDIO INPUT button
Selects from input audio signal, [AUDIO1], [AUDIO2], [AUDIO3].
4
SIZE button
Selects picture size, [FULL], [NORMAL], [WIDE] and [ZOOM].
See page 17.
5
PICTURE MODE button
Selects from picture mode, [HIGHBRIGHT], [STANDARD], [sRGB],
[CINEMA]. See page 17.
HIGHBRIGHT: for moving images such as DVD
STANDARD: for images
sRGB: for text based images
CINEMA: for movies.
6
MUTE button
To switch the mute function on/off.
7
VOLUME UP button
Increases the audio output level.
8
VOLUME DOWN button
Decreases the audio output level.
9
PIP (Picture In Picture) button
ON/OFF button: Toggle switches between PIP, POP, side-by-side
(aspect) and side-by-side (full). See page 21.
INPUT button: Selects the "picture in picture" input signal.
CHANGE button: Replaces to the main picture and sub picture.
NOTE: The PIP function does not support 1080i input signals. If a
1080i signal is used for PIP, then the sub picture on the screen will
be blank. The PIP function will work with 1080p signals.
10
STILL button
ON/OFF button: To switch the still picture mode on/off.
CAPTURE button: Captures the new picture.
NOTE: Still does not work when pixel clock is greater than 108MHz
and also not work for 1080i.
01_English 7
11
DISPLAY button
To switch the information OSM on/off. See page 17.
12
AUTO SETUP button
To enter the auto setup menu. See page 21.
13
MENU button
To switch the menu mode on/off.
14
UP button
Acts as button to move the highlighted area up to select the
adjustment with OSM menu.
Small screen which adjusted "PIP" mode moves up.
15
DOWN button
Acts as button to move the highlighted area down to select the
adjustment with OSM menu.
Small screen which adjusted "PIP" mode moves down.
16
MINUS button decrease
Acts as (-) button to decrease the adjustment with OSM menu.
Small screen which adjusted "PIP" mode moves left.
17
PLUS button increase
Acts as (+) button to increase the adjustment with OSM menu.
Small screen which adjusted "PIP" mode moves right.
18 SET button
Acts as SET button with OSM menu.
19 EXIT button
Turn to previous menu with OSM menu.
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor's
remote sensor during button operation.
Use the remote control within a distance of about 7 m/23 ft. from
the front of the LCD monitor's remote control sensor and at a
horizontal and vertical angle of within 30° within a distance of about
3 m/10 ft.

Handling the remote control

* Do not subject to strong shock.
* Do not allow water or other liquid to splash the
remote control. If the remote control gets wet,
wipe it dry immediately.
* Avoid exposure to heat and steam.
* Other than to install the batteries, do not open the remote
control.
Caution: Important, the remote control system may not function
when direct sunlight or strong illumination strikes the
remote control sensor of the LCD monitor, or when
there is an object in the path.
English-7
10/8/06, 11:12