Table of Contents Introduction Alarm About This Manual...........7 Principle of Operation........46 Symbols Glossary..........7 Arming the alarm...........48 Parts and Accessories........7 Disarming the alarm........48 At a Glance Steering Wheel At a Glance............10 Adjusting the Steering Wheel....49 Audio Control..........49 Child Safety Wipers and Washers Child Seats............22 Booster Seats..........23 Windscreen Wipers........51...
Page 4
Table of Contents Instrument Lighting Dimmer....137 Windows and Mirrors Clock..............137 Power Windows..........75 Cigar Lighter...........138 Exterior Mirrors..........77 Ashtray.............138 Electric exterior mirrors.........77 Auxiliary Power Points........138 Auto-Dimming Mirror........79 Cup Holders............139 Rear Quarter Windows.........79 Glove Box............139 Blind Spot Monitor........80 Storage compartments......140 Instrument Cluster Map Pockets............141 Seat Back Trays..........141 Gauges...............83 Glasses Holder..........142...
Page 5
Table of Contents Fuel and Refuelling Rear view camera Safety Precautions........155 Principle of Operation........177 Fuel Quality - Petrol........155 Using the Rear View Camera....177 Fuel Quality - E85.........155 Cruise Control Fuel Quality - Diesel........155 Principle of Operation........180 Catalytic Converter........156 Using Cruise Control........180 Fuel filler flap..........156 Refuelling............158 Adaptive cruise control...
Page 7
Table of Contents Loading the compact disc changer..286 Audio introduction Unloading the compact disc Important audio information....271 changer............287 Compact disc playback......287 Audio unit overview Fast forward/reverse........287 Audio unit overview........272 Shuffle/random..........287 Compact disc track compression..288 Audio system security Compact disc track scanning....288 Security code..........275 Ejecting compact discs......289 Lost security code........275...
Page 8
Table of Contents Connectivity General Information........318 Connecting an external device....319 Connecting an external device - Vehicles With: Bluetooth.........319 Using a USB device........320 Using an iPod..........322 Navigation introduction Road Safety...........326 Navigation system Getting started..........327 Appendices Type approvals..........329 Type approvals..........329 Type approvals..........329 Type approvals..........330 Electromagnetic compatibility....331...
PARTS AND ACCESSORIES Note: Some of the illustrations in this manual may be used for different models, Now you can be sure that your Ford so may appear different to your vehicle. parts are Ford parts However, the essential information in the Your Ford has been built to the highest illustrations is always correct.
Page 10
Exterior mirror been given Ford Original Parts. The Ford logo is clearly visible on the following parts if they are Ford Original Parts. If your vehicle has to be repaired, look for the clearly visible Ford branding and make sure that only Ford Original Parts have been used.
At a Glance Instrument panel overview - left-hand drive E74123...
Page 13
At a Glance Instrument panel overview - right-hand drive E75798 Lighting controls. See Lighting Control (page 56). Air vents. See Air Vents (page 112). Direction indicators. See Direction Indicators (page 62). Telephone control buttons. See Telephone controls (page 294). Voice control buttons. See Using voice control (page 300).
Page 14
At a Glance Information display controls. See Information Displays (page 89). Wiper lever. See Windscreen Wipers (page 51). Audio unit. See Audio unit overview (page 272). Navigation unit. See separate handbook. Stability control (ESP) switch. See Using Stability Control (page 170). Start-stop switch.
At a Glance Electric child safety locks Unlocking the vehicle E78278 Pull a door handle to unlock all the doors and the luggage compartment lid and disarm the alarm. E124779 Locking the vehicle See Child Safety Locks (page 28). Keyless entry E87384 E78276 Passive locking and unlocking requires a...
Page 16
At a Glance Autowipers See Keyless Entry (page 41). Adjusting the steering wheel WARNING Never adjust the steering wheel when the vehicle is moving. E70315 High sensitivity Low sensitivity Adjust the sensitivity of the rain sensor using the rotary control. See Autowipers (page 51).
Page 17
At a Glance Automatic main beam control WARNING The system does not relieve you of your responsibility to drive with due care and attention. A manual override may be necessary if the system fails to switch the main beam on or off. The system will automatically switch on E75188 main beam if it is dark enough and no other...
Page 18
At a Glance Electric folding mirrors The system displays a yellow indicator located in the exterior mirrors. E124736 See Blind Spot Monitor (page 80). E72623 Information displays See Electric exterior mirrors (page 77). Reverse mirror dipping Depending on the selected mirror position, the relevant exterior mirror will dip whenever you select reverse gear, giving you a view of the kerb.
At a Glance Manual climate control Direct the side air vents toward the side windows. Cooling the interior quickly Defrosting and demisting the windscreen E71381 Heating the interior quickly E71382 See Manual Climate Control (page 113). Automatic climate control E71377 Recommended settings for cooling E70304 See Automatic Climate Control (page...
Page 20
At a Glance Fuel filler flap Press the start button. Stopping the engine when the vehicle is moving WARNING Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not be locked, but higher effort will be required.
Page 21
At a Glance Automatic transmission WARNING We recommend that you remove the Note: Do not press the brake pedal when fuel nozzle slowly to allow any removing the key from the ignition switch. residual fuel to drain into the fuel Selector lever positions tank.
Page 22
At a Glance S-MAX E70529 Hold the brake pedal depressed and press E99105 down the switch. Galaxy Automatic release - Drive away release (DAR) Note: On vehicles with automatic transmission, the driver's door must be closed and the driver's seatbelt must be fastened before the DAR will operate.
Page 23
At a Glance Driver alert Towing the vehicle on four wheels WARNING CAUTION The system does not relieve you of For certain engine and transmission your responsibility to drive with due combinations, it is recommended not care and attention. to tow the vehicle with the drive wheels on the ground.
Child Safety CHILD SEATS WARNINGS Do not leave unattended children in your vehicle. If your vehicle has been involved in an accident, have the child restraints checked by properly trained technicians. Note: Mandatory use of child restraints E133140 varies from country to country. Only child restraints certified to ECE-R44.03 (or later) have been tested and approved for use in your vehicle.
Child Safety Child safety seat CAUTION When using a child seat on a rear seat, make sure that the child seat rests tightly against the vehicle seat. It may be necessary to lift or remove the head restraint. See Head Restraints (page 129). Booster seat (Group 2) E68920 Secure children that weigh between 13 and...
WARNINGS Please consult your Dealer for the When using a forward facing child seat on a second or third row seat, latest details relating to Ford always remove the head restraint recommended child seats. from that seat. See Head Restraints When you are using a group 0 or 0+ (page 129).
U¹ U¹ U¹ with airbag OFF Second row seats Third row Galaxy Third row S-MAX L, UF L, UF X Not suitable for children in this mass group. U Suitable for universal category child restraints approved for use in this mass group.
Page 28
At time of publishing the recommended Group O+ ISOFIX baby safety seat is the Britax Romer Baby Safe. Please consult your Dealer for the latest details relating to Ford recommended child seats. At time of publishing the recommended Group 1 ISOFIX child seat is the Britax Romer Duo.
Child Safety Attaching a child seat with top ISOFIX ANCHOR POINTS tethers WARNING WARNING Use an anti-rotation device when Do not attach a tether strap to using the ISOFIX system. We anything other than the correct recommend the use of a top tether tether anchor point.
Child Safety CHILD SAFETY LOCKS WARNING You cannot open the doors from inside if you have put the child safety locks on. Manual child safety locks Note: On vehicles with keyless entry, use the spare key. See Keyless Entry (page 41).
Occupant protection Driver and front passenger airbags PRINCIPLE OF OPERATION Airbags WARNINGS Do not modify the front of your vehicle in any way. This could adversely affect deployment of the airbags. Original text according to ECE R94.01: Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an airbag in front of it! E74302...
Occupant protection Note: The knee airbag has a lower Curtain airbags are fitted inside the trim deployment threshold than the front panels over the front and rear side airbags. During a minor collision, it is windows. Moulded badges in the B-pillar possible that only the knee airbag deploys.
Occupant protection The driver and front passenger seat belt retractors are fitted with a seat belt pretensioner. Seat belt pretensioners have a lower deployment threshold than the airbags. During minor collisions, it is possible that only the seat belt pretensioners will deploy. Status after a collision WARNING Seat belts subjected to strain, as a...
Occupant protection The retractor for the rear centre seat belt SEAT BELT HEIGHT is located in the roof. ADJUSTMENT To fasten the seat belt: Pull the belt out steadily. It may lock if you pull it sharply or if the vehicle is on a slope.
Occupant protection Deactivating the seat belt reminder See your dealer. USING SEAT BELTS DURING PREGNANCY E71313 Fitting the passenger airbag deactivation switch WARNING If you need to fit a child restraint on a seat protected by an operational E68587 airbag in front of it, have a passenger airbag deactivation switch fitted.
Page 36
Occupant protection Turn the switch to position A. When you switch the ignition on, check that the passenger airbag deactivation warning lamp illuminates. Enabling the passenger airbag WARNING Make sure that the passenger airbag is enabled when you are not using a child restraint on the front passenger seat.
Keys and Remote Controls Note: Further remote controls may be GENERAL INFORMATION ON programmed at this stage. RADIO FREQUENCIES 4. Press any button on each additional remote control within 10 seconds of CAUTIONS each other. The radio frequency used by your remote control can also be used by Reprogramming the unlocking other short distance radio...
Keys and Remote Controls Remote control without a folding Insert a screwdriver in the position key blade shown and gently push the clip. 2. Press the clip down to release the battery cover. E128810 E87964 3. Carefully remove the cover. Press and hold the pushbuttons on the edges to release the cover.
Page 39
Keys and Remote Controls E119190 4. Carefully insert the screwdriver in the position shown to open the remote control. E125860 CAUTION Do not touch the battery contacts or the printed circuit board with the screwdriver. 5. Carefully prise out the battery with the screwdriver.
Locks Locking and unlocking LOCKING AND UNLOCKING confirmation CAUTION When you unlock the doors, the direction indicators will flash once. Check your vehicle is locked before leaving it unattended. When you lock the doors, the direction indicators will flash twice. Central locking Locking and unlocking the doors with the key...
Page 41
Locks Locking and unlocking the doors Locking and unlocking the doors and the luggage compartment lid from inside with the remote control Driver's door E87379 Unlock Lock Luggage compartment lid unlock (press twice) E71958 Locking the doors and the luggage Lock all doors compartment lid with the remote control...
Locks Luggage compartment lid Reprogramming the unlocking function Opening the luggage compartment lid The unlocking function may be reprogrammed so that only the driver’s door is unlocked. See Programming the remote control (page 35). GLOBAL OPENING AND CLOSING You can also operate the electric windows with the ignition off via the global opening and global closing function.
Locks Global closing WARNING Take care when using global closing. Vehicles without keyless entry In an emergency, press the button on the driver’s door handle to stop. WARNING Take care when using global closing. Note: Global closing can be activated using In an emergency, press a button the button on the driver s door handle.
Locks E87384 E78276 Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges. These are located approximately one and a half metres from the driver and front passenger door handles and the luggage compartment lid.
Locks Luggage compartment lid Unlocking only the driver's door Note: The luggage compartment lid cannot If the unlocking function is reprogrammed be closed and will pop back up if the passive so that only the driver’s door is unlocked ( key is located inside the luggage See Keys and Remote Controls (page compartment.
Page 46
Locks Locking and unlocking the doors with the key blade E87964 Carefully remove the cover. 2. Remove the key blade and insert it into the lock.
If you lose a key, you can obtain a replacement from your Ford Dealer. If possible, provide them with the key number from the tag provided with the original keys. You can also obtain additional keys from your Ford Dealer.
Alarm PRINCIPLE OF OPERATION WARNING The sensors must not be covered up. Alarm system Do not activate the alarm with full guard if any persons, animals or other Your vehicle may be equipped with one of moving objects are inside the vehicle. the following alarm systems: Perimeter alarm.
Page 49
Alarm On vehicles with a battery back-up If you select Ask on Exit, the message sounder, if someone disconnects the Reduced guard? appears in the vehicle battery or the battery back-up instrument cluster display each time you sounder itself. switch the ignition off. If the tilt sensors detect a change in the If you wish to arm the alarm with reduced inclination of the vehicle.
Alarm Vehicles with keyless entry Press the right arrow button on the steering wheel to enter the main menu. Note: A valid passive key must be located 2. Highlight Setup with the up and down within the detection range of that door for arrow buttons and press the right arrow keyless entry.
Steering Wheel ADJUSTING THE STEERING WARNING WHEEL Make sure that you fully engage the locking lever when returning it to its original position. WARNING Never adjust the steering wheel AUDIO CONTROL when the vehicle is moving. Note: Make sure that you are sitting in the correct position.
Steering Wheel Seek Press a seek button to: tune the radio to the next station up or down the frequency band play the next or the previous CD track fast forward or rewind the cassette tape. Press and hold a seek button to: tune the radio up or down the frequency band seek through a CD track.
Wipers and Washers WINDSCREEN WIPERS AUTOWIPERS CAUTIONS Do not switch autowipers on in dry weather conditions. The rain sensor is very sensitive and the wipers may operate if dirt, mist or flies hit the windscreen. Replace the wiper blades as soon as they begin to leave bands of water and smears.
Wipers and Washers Adjust the sensitivity of the rain sensor ADJUSTING THE WINDSCREEN using the rotary control. With low WASHER JETS sensitivity, the wipers will operate when the sensor detects a lot of water on the windscreen. With high sensitivity, the wipers will operate if the sensor detects a small amount of water on the windscreen.
Wipers and Washers Washer CHECKING THE WIPER BLADES WARNING Do not operate the rear window washer for more than 10 seconds or when the reservoir is empty. E66644 E70777 Run the tip of your fingers over the edge of the blade to check for roughness. Pull the lever fully towards the steering Clean the wiper blade lips with water wheel and hold it to operate the washer.
Page 56
Wipers and Washers Rear window wiper blades Set the windscreen wipers in the service position. E75184 E93783 E75188 Switch off the ignition and move the wiper lever to position A within three seconds. Release the lever when the windscreen wipers have moved to the service position. Lift the wiper arms.
Lighting One side LIGHTING CONTROL Lighting control positions E75505 Right-hand side Left-hand side Main and dipped beam E70718 Side and tail lamps Headlamps Parking lamps CAUTION E70725 Prolonged use of the parking lamps will discharge the battery. Pull the lever fully towards the steering wheel to switch between main and dipped Switch off the ignition.
If the lights of oncoming vehicles are hidden by obstacles (for example guard rails) the system may not deactivate the main beam. Always fit Ford Original Parts when replacing headlamp bulbs. Other bulbs may reduce system performance. Check and replace wiper blades...
Page 60
Lighting Note: Keep the windscreen free from obstructions such as bird droppings, insects and snow or ice. The system will automatically switch on main beam if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead the system will switch off main beam before it can...
Lighting Use the main beam lever to switch WARNINGS between main beam and dipped beam. Only use the rear fog lamps when visibility is restricted to less than 50 Note: This is a temporary override and the metres (164 feet). system will return to automatic operation after a short period.
Lighting Recommended headlamp levelling switch positions Load Load in luggage Switch position Second row compartment Front seats Third row seats seats 0 (0.5) 1 (0.5) 3 (0.5) 4 (1.5) See Vehicle Identification Plate (page 265). Vehicles with active suspension. ADAPTIVE HEADLAMPS E72897...
Page 63
Lighting without AFS with AFS A message will appear in the information The AFS adjusts the headlamp dipped display if the system malfunctions. See beam depending on vehicle direction and Information Messages (page 102). The speed. It improves visibility when you are headlamps will move to a fixed central or driving at night and helps to reduce dipped position.
Lighting If you set the switch to position B, the HAZARD WARNING FLASHERS courtesy lamp will come on when you unlock or open a door or the luggage compartment lid. If you leave a door open with the ignition switch off, the courtesy E71943 lamp will go off automatically after some For item location: See At a Glance (page...
Lighting LED interior lighting Vanity mirror lamps E72900 E131657 Individual lamp on and off switch If you switch off the ignition, the vanity Master on and off switch mirror lamps will go off automatically after a short time to prevent the vehicle battery You can control all lamps using switch B.
Lighting Note: When fitting the headlamp, make sure that you fully engage the headlamp in the lower fixing point. Note: When fitting the headlamp, make sure that the front screw is located in the headlamp moulding before you install it. Note: When fitting the headlamp, tighten the front screw first and then the rear screw.
Page 67
Lighting Headlamp main beam Remove the headlamp. See Removing a Headlamp (page 63). E72258 Direction indicator Headlamp main beam Headlamp dipped beam Cornering lamp E72261 2. Disconnect the electrical connector. Direction indicator 3. Release the clip and remove the bulb. Remove the headlamp.
Page 68
Lighting Side repeater E72262 2. Disconnect the electrical connector. E72263 3. Release the clip and remove the bulb. Carefully remove the side repeater. Daytime running lamps Note: These are not serviceable items, please consult your dealer if they fail. E72291 2.
Page 69
Lighting E72264 E126440 Insert a screwdriver into the gap 2. Disconnect the electrical connector. between the mirror housing and the Note: You cannot separate the fog lamp mirror glass and release the metal bulb from the bulb holder. retaining clip. 3.
Page 70
Lighting Front fog lamp and side lamp Rear lamps (S-MAX) (Galaxy) Direction indicator, tail and brake lamp Note: These are not serviceable items, please consult your dealer if they fail. E126274 Reversing lamp, tail lamp and fog lamp E126538 Remove the screw.
Page 71
Lighting Rear lamp (Galaxy) Direction indicator, tail and brake lamp E74076 2. Remove the wing nuts. 3. Remove the lamp. 4. Disconnect the electrical connector. E75380 Remove the trim panel. E126303 5. Remove the screws. 6. Remove the bulb holder.
Page 72
Lighting Reversing lamp, tail lamp and fog lamp E72792 3. Remove the lamp. E72794 Remove the trim panel. 4. Disconnect the electrical connector. E72795 E72793 2. Remove the wing nuts. Note: On some vehicles the tail lamps are LED. These are not serviceable items, please 3.
Page 73
Lighting 6. Remove the bulb holder. Vehicles without interior sensors Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it. Central high mounted brake lamp Note: These are not serviceable items, please consult your dealer if they fail. Number plate lamp E72788 Carefully prise out the lens.
Page 74
Lighting Reading lamps Vehicles without interior sensors E73939 3. Remove the bulb. Vanity mirror lamp E72796 Carefully prise out the lens. 2. Remove the lens. 3. Remove the bulb. Vehicles with interior sensors E72785 Carefully prise out the lamp. 2. Remove the bulb. E72786 Carefully prise out the lamp.
Front direction indicator PY21W Headlamp main beam Headlamp dipped beam Cornering lamp Side repeater Approach lamp Front fog lamp (S-MAX) Front fog lamp (Galaxy) Side lamp Rear direction indicator PY21W Rear fog lamp P21W Reversing lamp P21W Number plate lamp...
Windows and Mirrors Driver s door switches POWER WINDOWS WARNING Do not operate the electric windows unless they are free from obstruction. Note: If you operate the switches often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.
Windows and Mirrors Safety switch for rear windows Overriding the anti-trap function CAUTION WARNING While you close the window for the On some vehicles, pressing the third time, the anti-trap function is switch will also lock the rear doors disabled. Make sure there are no from inside.
Windows and Mirrors Safety mode ELECTRIC EXTERIOR MIRRORS WARNING The anti-trap function is not active during this procedure. If the system detects a malfunction, it enters a safety mode. The windows will move for only about 0.5 seconds at a time and then stop again.
Page 80
Windows and Mirrors Electric folding mirrors If you press the switch again while the mirrors are moving, they will stop and Automatic folding and unfolding reverse the direction of movement. Note: When the mirrors are operated often Note: If the mirrors have been folded using during a short period of time, the system the manual fold button they can only be may become inoperable for a period of time...
Windows and Mirrors AUTO-DIMMING MIRROR E71028 The auto-dimming mirror will adjust automatically when hit by glaring light from behind. It will not work when you have E95383 selected reverse gear. Closing REAR QUARTER WINDOWS Manual rear quarter windows Opening E95384 E72126...
Windows and Mirrors BLIND SPOT MONITOR Blind spot information system (BLIS) WARNINGS The system is not designed to prevent contact with other vehicles or objects. The system only provides a warning to assist you in detecting vehicles in the blind spot zones. The system will not detect obstacles, pedestrians, motorcyclists or cyclists.
Page 83
Windows and Mirrors Using the system CAUTIONS Do not place items such as bumper The system displays a yellow indicator stickers in this area. located in the exterior mirrors. Repairs to these areas using body filler will affect the performance of the system.
Page 84
Windows and Mirrors Circumstances where false alerts may CAUTION occur: The sensors may not detect vehicles Road guardrails. in heavy rain or other conditions that Motorway concrete walls. cause disruptive reflections. Construction areas. Note: Keep the rear bumper area Sharp turns around a building. surrounding the sensors free from dirt, ice Bushes and trees.
Instrument Cluster Type 3 E130765 Tachometer Speedometer Engine coolant temperature gauge Fuel gauge Message centre. See Information Displays (page 89). CAUTION Engine coolant temperature gauge Do not restart the engine until the Note: On type 3 this gauge is shown within cause of overheating has been the message centre and will not be resolved.
Instrument Cluster Fuel gauge Airbag warning lamp Note: On type 3 this gauge is shown within If it illuminates when you are the message centre. driving, this indicates a malfunction. Have the system The arrow adjacent to the fuel pump checked by a properly trained technician.
Page 88
Instrument Cluster Front fog lamp indicator If it stays on after starting or illuminates when driving, this It will illuminate when you switch indicates a malfunction. Stop the front fog lamps on. your vehicle as soon as it is safe to do so and switch the engine off.
Page 89
Instrument Cluster Lane departure warning indicator Rear fog lamp indicator It will illuminate when this It will illuminate when you switch feature is switched off or in the rear fog lamps on. conjunction with a message. The indicator will go out when you switch the Seat belt reminder system back on or when you switch the ignition off.
Instrument Cluster AUDIBLE WARNINGS AND INDICATORS Switching the chimes on and off You can deactivate certain chimes. To set which chimes should sound: E70499 Press the right arrow button on the steering wheel to enter the main menu. 2. Highlight Setup with the up and down arrow buttons and press the right arrow button.
Information Displays Press the up and down arrow buttons: GENERAL INFORMATION to scroll through the trip computer WARNING displays to scroll through and highlight the Do not operate the information options within a menu. display controls when the vehicle is moving.
Information Displays Function Type 1 Type 2 Type 3 Navigation control CD control CD changer control Radio control Phone control Auxiliary input control Press the up and down arrow buttons on Type 1 the steering wheel to scroll through the trip computer displays.
Page 93
Information Displays Menu structure BLIS Gear Shifting ECO MODE Anticipation Speed For more Info Reset trip Trip Odo Avg Fuel Avg Speed All values Information Messages Auto StartStop Clock Set Clock 24 Hour Mode 12 Hour Mode E131626 Press the up and down arrow buttons on Type 2 the steering wheel to scroll through the trip computer displays.
Page 94
Information Displays Menu structure BLIS Gear shifting ECO MODE Anticipation Speed For more Info Reset Trip Trip Odo Avg fuel Avg speed Messages Information Auto StartStop Tyre Press. Set Clock Clock 24 Hour Mode 12 Hour Mode Display Help Screen Setup Configure Radio Info...
Page 95
Information Displays Low Fuel Chimes General info. General warn. Home light Forw Alert Normal High Hill Launch Auto Manual Check Tyre Pressure Low load High load Full guard Alarm Reduced Ask on exit Time 1 Set Time Aux. Heater Monday Tuesday Wednesday Parkheater...
Page 96
Information Displays Type 3 CD changer Radio Phone E88048 Trip computer Use the controls to scroll through the menu displays. Settings Device list The highlighted icon shows the current menu in use. Auxiliary input Navigation...
Page 97
Information Displays Menu structure Navigation Home Destinations Destinat. mem. Destinations Destinat. A-Z Destinations Last destinat. Cancel guidan. Folder / Tracks Folder / Tracks CD changer CD 1 CD 2 Folder / Tracks CD 3 Folder / Tracks CD 4 Folder / Tracks CD 5 Folder / Tracks CD 6...
Page 98
Information Displays Settings BLIS Gear shifting ECOMODE Anticipation Speed More info Messages Information Driver alert Auto StartStop Tyre Pressure Coolant temperature Set Clock Clock 24-hour mode 12-hour mode Setup Driver alert Display Colour themes Configure Help Screen NAV info Always off On guidance Always on Language...
Page 99
Information Displays Low Fuel Chimes General info. General warn. Home light Forw Alert Normal High Lane depart Normal Sensitivity High Intensity High Normal Auto beam Sensitivity High Normal Hill Launch Auto Manual Check Tyre Pressure Low load High load Full guard Alarm Reduced Ask on exit...
Information Displays Set Time Time 1 Park heater Monday Tuesday Wednesday Thursday Friday Saturday Sunday Set Time Time 2 Monday Tuesday Wednesday Thursday Friday Saturday Sunday Once Active now Auxiliary input E88067 Average fuel consumption TRIP COMPUTER Indicates the average fuel consumption since the function was last reset.
Page 101
Information Displays Type 1 and 2 Resetting the trip computer using the main menu To reset a particular display: 10:20 Press the right arrow button on the steering wheel to enter the main menu. 2. Highlight Reset Trip with the up and down arrow buttons and press the right Average Fuel arrow button.
Information Displays 3. Hold the OK button pressed. 2. Highlight Setup with the up and down arrow buttons and press the right arrow button. PERSONALISED SETTINGS 3. Highlight Display and press the right arrow button. The following information is displayed in the information display if you have 4.
Page 103
Information Displays 6. Highlight the desired setting and press 6. Press the left arrow button to exit the the OK button to confirm the setting. menu. Hold the left arrow button pressed to return to the trip computer Press the left arrow button to exit the display.
Information Displays Message symbols Type 3 Highlight Settings with the up and See Owner’s handbook. down arrow buttons and press the right arrow button. 2. Highlight Setup with the up and down Have the system checked at the arrow buttons and press the right arrow next service.
Page 105
Information Displays Active suspension Message Indicator Action Have the system checked by a properly trained IVDC malfunction amber technician. IVDC comfort See Active suspension (page 174). IVDC normal See Active suspension (page 174). IVDC sport See Active suspension (page 174). Airbag Message Indicator...
Page 106
Information Displays Message Indicator Action Lane departure amber The system has malfunctioned. Have this warn. malfunct. checked as soon as possible. Battery and charging system Message Indicator Action Stop your vehicle as soon as it is safe to do so Overvoltage: Stop and switch off the ignition.
Page 107
Information Displays Climate control Message Indicator Action Aux. Heater on amber See Auxiliary Heater (page 120). Cruise control and Adaptive cruise control (ACC) Message Indicator Action Have the system checked by a properly trained ACC malfunction amber technician as soon as possible. Clean radar sensor amber See Adaptive cruise control (ACC) (page 182).
Page 108
Information Displays Engine immobiliser Message Indicator Action Immobiliser active amber See Engine immobiliser (page 45). Hill start assist Message Indicator Action Hill Launch not Have the system checked by a properly trained amber available technician. Please use park amber See Hill Start Assist (page 171). brake! Hill Launch Assist See Hill Start Assist (page 171).
Page 109
Information Displays Lighting Message Indicator Action Front lights Have the system checked by a properly trained amber malfunction technician as soon as possible. One or both of the headlamp dipped beam bulbs Low beam: Bulb have blown. Check the headlamp dipped beam fault bulbs.
Page 110
Information Displays Occupant protection Message Indicator Action Have the system checked by a properly trained Crash mode technician as soon as possible. Parking brake Message Indicator Action Park brake applied See Parking Brake (page 166). Park brake applied amber See Parking Brake (page 166). Electric parking brake (EPB) Message Indicator...
Page 111
Information Displays Stability control (ESP) Message Indicator Action Have the system checked by a properly trained ESP malfunction technician as soon as possible. ESP off See Using Stability Control (page 170). Start-stop Message Message Action indicator Switch the ignition off before leaving the vehicle Auto StartStop Switch if the system has shut down the engine.
Page 112
Information Displays Message Indicator Action One or more of the tyres are significantly under- inflated. This message may be displayed after a Check tyre pres- new sensor has been installed. Check the tyres sures and inflate them to the recommended pressure. See Technical Specifications (page 262).
Page 113
Information Displays Voice control Message Indicator Action Voice control See Voice control (page 300). Please speak Voice control Not See Voice control (page 300). recognised Voice control Not See Voice control (page 300). allowed...
Climate Control Warming the interior PRINCIPLE OF OPERATION Direct the air towards your feet. In cold or Outside air humid weather conditions, direct some of the air towards the windscreen and the Keep the air intakes forward of the door windows. windscreen free from obstruction (snow, leaves etc.) to allow the climate control Cooling the interior...
Climate Control Second row air vents Third row air vents E73132 MANUAL CLIMATE CONTROL Air distribution control E71379 Windscreen Footwell and windscreen E73131 Footwell Air flow through lower air vent Face level and footwell Air flow through upper air vent Face level Upper air vent Face level and windscreen...
Climate Control Blower Ventilation E71378 Set the air distribution control, blower and air vents to suit your requirements. Air conditioning Switching the air conditioning on and E75470 If you turn the blower off, the air Note: If you switch the blower off, the conditioning will turn off.
Climate Control Defrosting and demisting the You can switch the air conditioning and windscreen recirculated air on and off while the air distribution control is set to position A. Note: Turn the air conditioning on to assist If necessary, switch the heated windows windscreen and side window demisting.
Page 118
Climate Control Triple-zone E70302 Note: For information on the automatic Your vehicle is fitted with either a climate control, on vehicles fitted with a dual-zone or triple-zone system. When the combined Navigation and automatic system is in mono mode, all the climate control system, see separate temperature zones are linked to the driver's handbook.
Climate Control Mono mode Low speed In mono mode, the temperature settings for both the driver’s and passenger’s side E94615 are linked. If you adjust the temperature Use the buttons to adjust the blower using the rotary control on the driver’s side, speed.
Page 120
Climate Control The blower speed and the temperature Dual-zone control operate automatically and cannot be adjusted manually. The blower is set to high speed and the temperature to HI. When you select windscreen defrosting and demisting, the heated screens switch on automatically and switch off after a short time.
Page 121
Climate Control Switching between front and rear air Note: When the front air conditioning is conditioning mode switched off, you cannot have rear air conditioning. Rear blower High speed Low speed E94615 When the system is in rear air conditioning mode, use the buttons to adjust the blower speed.
Climate Control When the system is in rear air conditioning The parking heater operates independently mode, press button A to switch only the of the vehicle heater by heating the rear system on and off. engine’s coolant circuit. It is fed from the vehicle fuel tank.
Page 123
Climate Control Programming the parking heater Note: The programmed time is the time at Park Heater which you wish the vehicle to be warm and ready to drive, not the time at which the Program 1 heater switches on. Note: You must programme the times at Program 2 least 70 minutes in advance of the time you One-Time...
Page 124
Climate Control Highlight Program 1 and press the right Programming the function One-Time arrow button. Highlight One-Time and press the right 2. Highlight the day on which the heater arrow button. should warm up the vehicle. 2. Press the OK button and the hours 3.
Page 125
Climate Control Starting The LED on the transmitter flashes green or red for about two seconds. This Hold the transmitter with the antenna indicates the signal was not transmitted upwards and press the ON button for at correctly. Repeat the transmission. least two seconds.
Page 126
Climate Control 3. Install a new battery (3.3V type The fuel operated heater aids in warming CR1-3N) with the + facing upwards. the engine and the vehicle interior on vehicles with a diesel engine. It is switched 4. Re-assemble the remote control. on or off automatically depending on the outside air temperature and the coolant Programming the transmitter...
Page 127
Climate Control Diesel auxiliary heater (depending on country) The diesel auxiliary heater (PTC electrical heater) aids in warming the vehicle interior on vehicles with a diesel engine. It is switched on or off automatically depending on the outside air temperature, the coolant temperature and the alternator load.
Seats bend your legs slightly so that you can SITTING IN THE CORRECT press the pedals fully. POSITION position the shoulder strap of the seat belt over the centre of your shoulder and position the lap strap tightly across your hips. Make sure that your driving position is comfortable and that you can maintain full control of your vehicle.
Seats Adjusting the lumbar support Adjusting the angle of the seatback E70729 E70731 Adjusting the height of the driver s seat POWER SEATS 2-way electric seat E70730 E70733...
Seats HEAD RESTRAINTS REAR SEATS Adjusting the head restraint Second row seats Moving the seats backwards and WARNINGS forwards Raise the rear head restraint when the rear seat is occupied by a WARNING passenger. Rock the seat backwards and When using a forward facing child forwards after releasing the lever to restraint on a rear seat, always make sure that it is fully engaged in...
Page 132
Seats Adjusting the seatback E72704 E72645 To recline the seatback, pull the lever on the outboard seats or the strap on the centre seat and lean back against the seatback until it reaches the desired position. 2. To raise the seatback, pull the lever up and push the seat cushion forwards using your weight.
Page 133
Do not sit in a third row seat when the second row seat in front of it is folded flat. E72705 Moving the seats backwards and forwards (Galaxy) WARNING Rock the seat backwards and forwards after releasing the lever to make sure that it is fully engaged in its catch.
Page 134
When folding the seatbacks down, hold the seatback to avoid getting your fingers caught between the seatback and seat frame. E72647 Adjusting the seatback (Galaxy) E72707 E75381 To recline the seatback, pull the strap and lean back against the seatback E72648 until it reaches the desired position.
Page 135
Seats Pull the loop at the rear of the seat cushion and fold the seat cushion forwards until it lies flat on the floor (1). 2. Grasp the grip (A) and pull the loop (B) at the base of the seatback upwards and rearwards (2).
Seats Note: Only the front seat settings are stored HEATED SEATS when you switch off the ignition. CAUTION Raising and lowering the temperature automatically Operating this function with the engine off will drain the battery. Press and hold the relevant button. Raising and lowering the temperature manually Press the relevant button repeatedly.
Seats FRONT SEAT ARMREST E70602 E95256 Note: The number of illuminated lights beside the button indicates the selected step. Note: The ventilation setting is indicated in blue. Note: When no light is illuminated, the ventilation is switched off. Note: The settings are stored when the ignition is switched off.
E74809 Pull the blind up and attach it to the hooks (A). E125025 The sun blind is operated by a switch Roof (Galaxy) located between the sun visors. Opening and closing the sun blind E74808 Roof (S-MAX) WARNING...
Convenience features Opening and closing the sun blind 3. Press and hold switch B to the first automatically action point, until the blind fully opens. 4. Press and hold switch A to the first Press the switch to the second action point action point, until the blind fully closes.
Rear ashtray off. Note: You can use the socket to power 12 volt appliances that have a maximum current rating of 15 Amperes. Use only Ford accessory connectors or connectors specified for use with SAE standard sockets. E73705 To remove the ashtray, open it, press it E72972 down against the spring and remove it.
Note: You can use the socket to power 12 volt appliances that have a maximum WARNING current rating of 15 Amperes. Use only Ford accessory connectors or connectors Do not use the trays when the vehicle specified for use with SAE standard sockets.
Convenience features E72905 STORAGE COMPARTMENTS WARNING Do not drive with any storage compartment lid open. Make sure that you secure the lid before setting off. CAUTION Do not keep heat-sensitive items and liquids in any storage compartment. Front storage compartments E72905 Under seat storage compartment E72978...
Convenience features Vehicles with Premium sound system CAUTION Do not attempt to open the left-hand cover. MAP POCKETS E73067 Under floor storage compartment WARNING When you are using a child restraint with a support leg on a second row seat, make sure that you locate the support leg securely on the under floor E74686 storage compartment lid.
Convenience features WARNINGS The memory store function cannot be used when the vehicle is moving. E72630 GLASSES HOLDER E86768 Seat adjustment controls See Power Seats (page 127). Memory pre-set buttons Up to four different driver's seat and exterior mirror positions can be stored in the memory.
Convenience features 2. Adjust the seat and exterior mirrors to 3. Release the seat adjustment control the desired position. and immediately press and hold the switch in the same direction for at least 3. Press and hold the desired pre-set 3 seconds.
Convenience features AUXILIARY INPUT (AUX IN) FLOOR MATS SOCKET WARNING When using the floor mats, always make sure the floor mat is properly secured using the appropriate fixings and positioned so that it does not interfere with the operation of the pedals. E71969 See separate audio handbook.
Starting and Stopping the Engine II The ignition is switched on. All electrical GENERAL INFORMATION circuits are operational. Warning lamps and indicators illuminate. This is the key General points on starting position when driving. You must also select If the battery has been disconnected the it when being towed.
Starting and Stopping the Engine Ignition on Type 1 Press the start button once. All electrical circuits are operational, warning lamps and indicators illuminate. Starting with automatic transmission Note: Releasing the brake pedal during engine start will stop the engine cranking and return to ignition on.
Starting and Stopping the Engine Press and hold the start button for two seconds, or press three times within three seconds. STEERING WHEEL LOCK WARNING Always check that the steering is unlocked before attempting to move your vehicle. Vehicles without keyless starting E85767 To activate the steering wheel lock;...
Starting and Stopping the Engine Cold or hot engine Vehicles with automatic transmission Select park or neutral. All vehicles 2. Fully depress the accelerator pedal and CAUTION hold it there. When the temperature is below -20°C 3. Fully depress the brake pedal. (-4°F), switch the ignition on for at 4.
Starting and Stopping the Engine If the temperature is expected to remain STARTING A DIESEL ENGINE below -10°C (14°F), it is recommended that you increase the proportion of petrol Cold or hot engine in the tank by topping up with 95 octane unleaded petrol if the tank is not already All vehicles full.
Starting and Stopping the Engine Regeneration Drive your vehicle at a constant speed, preferably on a main road or motorway, WARNING for up to 20 minutes. Avoid prolonged idling and always Do not park or idle your vehicle over observe speed limits and road dry leaves, dry grass or other conditions.
Page 153
Starting and Stopping the Engine E97918 Connect the engine heater for 2 to 3 hours before starting the engine.
Start-Stop Note: If you stall the engine, and then PRINCIPLE OF OPERATION depress the clutch pedal within a couple of seconds, the system will automatically CAUTION restart the engine. For vehicles with Start-stop the Note: The Start-stop indicator will battery requirement is different. It illuminate green when the engine shuts must be replaced by one of exactly down.
Page 155
Start-Stop Low engine operating temperature. Low brake system vacuum. If a road speed of 5 km/h (3 mph) has not been exceeded. To re-start the engine Note: The gear lever must be in the neutral position. Depress the clutch pedal. The system may automatically restart the engine under certain conditions, for example:...
Eco Mode Anticipation PRINCIPLE OF OPERATION Adjusting your vehicle speed and the The system assists the driver to drive more distance to other vehicles without the need efficiently by constantly monitoring for heavy braking or acceleration will characteristics of gear changing, improve fuel consumption.
Fuel and Refuelling SAFETY PRECAUTIONS CAUTIONS Do not use leaded petrol or petrol with additives containing other metallic WARNINGS compounds (e.g. manganese-based). Stop refuelling after the fuel nozzle They could damage the emission system. stops the second time. Additional fuel will fill the expansion space in Do not use methanol instead of E85.
Note: We recommend that you use only Do not switch the ignition off when high quality fuel. driving. Note: The use of additives or other engine treatments not approved by Ford is not FUEL FILLER FLAP recommended. Note: We do not recommend the prolonged WARNINGS...
Fuel and Refuelling E139203 Incorrect position Correct position 3. Do not lift the nozzle during refilling. This can affect the flow of fuel and shut off of E139202 the fuel nozzle before the fuel tank is full. Note: When you insert the fuel nozzle, a spring loaded inhibitor will open if the correct size nozzle is detected.
CAUTION accessories fitted and towing etc. Do not attempt to start the engine if Your Ford dealer can give you advice on you have filled the fuel tank with the improving your fuel consumption. incorrect fuel. This could damage the engine.
Page 161
Fuel and Refuelling S-MAX Fuel Consumption Figures CO2 Emis- Urban Extra-Urban Combined sions Variant l/100 km l/100 km l/100 km g/km (mpg) (mpg) (mpg) 1.6L EcoBoost SCTi (Sigma) Stage V (118kW/160PS), 6- 9.4 (30.1) 5.7 (49.6) 7 (40.4) speed manual transmission 2.0L Duratec-HE (MI4) Stage IV (107kW/145PS), 5- 11 (25.7)
Page 162
Fuel and Refuelling CO2 Emis- Urban Extra-Urban Combined sions Variant l/100 km l/100 km l/100 km g/km (mpg) (mpg) (mpg) 1.6L Duratorq-TDCi (DV) Diesel Stage V (85kW/115PS), 6-speed 5.9 (47.9) 4.9 (57.6) 5.2 (54.3) manual transmission with start-stop 2.0L Duratorq-TDCi (DW) Diesel Stage IV (103kW/140PS), Durashift 7.7 (36.7)
Page 163
Fuel and Refuelling Galaxy Fuel Consumption Figures CO2 Emis- Urban Extra-Urban Combined sions Variant l/100 km l/100 km l/100 km g/km (mpg) (mpg) (mpg) 1.6L EcoBoost SCTi (Sigma) Stage V (118kW/160PS), 6- 9.7 (29) 5.8 (48.7) 7.2 (39.2) speed manual transmission 2.0L Duratec-HE (MI4)
Page 164
Fuel and Refuelling CO2 Emis- Urban Extra-Urban Combined sions Variant l/100 km l/100 km l/100 km g/km (mpg) (mpg) (mpg) 2.0L Duratorq-TDCi (DW) Diesel Stage V (120kW/163PS), Durashift 7.2 (39.2) 4.9 (57.6) 5.7 (49.6) 6-speed manual transmis- sion 2.0L Duratorq-TDCi (DW) Diesel Stage IV 9.7 (29.1) 5.7 (49.6)
Transmission MANUAL TRANSMISSION Neutral Drive CAUTION Sport mode and manual shifting Do not engage reverse gear when the vehicle is moving. This can cause WARNING damage to the transmission. Apply the brakes before moving the selector lever and keep them applied until you are ready to move off.
Page 166
Transmission Drive modes Neutral In this position, power is not transmitted The transmission will select the to the drive wheels but the transmission is appropriate gear for optimum performance not locked. You can start the engine with based on ambient temperature, road the selector lever in this position.
Page 167
Transmission E81705 Insert a small flat-bladed tool into the slot. 2. Turn the tool through 90 degrees. 3. Push downwards on the tool to detach the gaiter frame from the trim panel. 4. Push downwards on the gaiter frame to release the lever and move the selector lever from the park position.
Brakes you take corners too fast. PRINCIPLE OF OPERATION the road surface is poor. Note: Depending on applicable laws and regulations in the country for which your PARKING BRAKE vehicle was originally built, the brake lamps may flash if you brake heavily. Applying the parking brake Note: Occasional brake noise is normal and often does not indicate a concern.
Brakes Parking on a hill Parking on a hill If you have to park facing uphill, select first If you have to park facing uphill, select first gear and turn the front wheels away from gear and turn the front wheels away from the kerb.
Page 170
Brakes Preventing automatic application Applying the EPB when the vehicle of the EPB is moving WARNINGS WARNING Do not leave the vehicle if you have With the exception of emergency not applied the EPB. Remember that conditions (for example, the brake if you press down the switch while pedal does not work or is blocked), removing the key from the ignition the EPB...
Page 171
Brakes The brake system warning lamp will go off Moving off with a trailer (vehicles with to confirm that the EPB has been released. manual transmission) Note: On vehicles with manual Depending on the gradient and the weight transmission, if the gear lever is in neutral of the trailer, the vehicle and trailer may when you release the clutch pedal and roll backwards slightly when you move off...
Stability Control Stability control (ESP) warning lamp PRINCIPLE OF OPERATION While driving, it flashes during activation Electronic stability programme of the system. See Warning Lamps and (ESP) Indicators (page 85). WARNING Emergency brake assist The system does not relieve you of WARNING your responsibility to drive with due care and attention.
Hill Start Assist PRINCIPLE OF OPERATION The system makes it easier to pull away when the vehicle is on a slope without the need to use the parking brake. When the system is active, the vehicle will remain stationary on the slope for a short time after you release the brake pedal.
Hill Start Assist Note: When HLA is in manual activation Press the brake pedal to bring the mode, only use the HLA when pulling away vehicle to a complete standstill. Keep uphill on gradients greater than 3%. If the the brake pedal depressed. vehicle is on the flat or on a downhill slope, 2.
Page 175
Hill Start Assist WARNING When HLA is active and the system detects a malfunction, the HLA is deactivated and the message Please use park brake! followed by Hill Launch A .not available is displayed in the information display. The vehicle is still safe to be driven and can be repaired during the next service.
Active suspension System malfunction PRINCIPLE OF OPERATION The active suspension system will switch The active suspension provides improved off automatically if it malfunctions. The handling, comfort and stability by suspension will be set to a fail-safe continuously adjusting the damper condition that will enable you to continue properties to the current road and driving driving but you will not be able to change...
Parking Aids Note: The parking aid may emit false tones PRINCIPLE OF OPERATION if it detects a signal using the same frequency as the sensors or if the vehicle is WARNING fully laden. The parking aid does not relieve you Note: The outer sensors may detect the of your responsibility to drive with side walls of a garage.
Parking Aids You will hear an intermittent tone at a distance of up to approximately 150 centimetres (59 inches) between the obstacle and rear bumper, 80 centimetres (31 inches) between the obstacle and front bumper and 50 centimetres (20 inches) to the side.
20 centimetres (8 inches). E99105 Do not apply pressure to the camera. Galaxy Note: Keep the camera free from dirt, ice and snow. Do not clean with sharp objects, degreaser, wax or organic products. Use only a soft cloth.
Rear view camera The camera may not operate correctly in the following conditions: Dark areas. Intense light. If the ambient temperature increases or decreases rapidly. If the camera is wet, for example in rain or high humidity. If the camera's view is obstructed, for example by mud.
Page 181
Rear view camera Amber - 2 metres (79 inches) Shows the centre line of the projected vehicle path Note: When reversing with a trailer, the lines on the screen show the vehicle direction and not the trailer. Deactivating the rear view camera Note: Disengage reverse gear.
Cruise Control Press the SET+ switch or the SET- switch PRINCIPLE OF OPERATION to store and maintain your current speed. The cruise control indicator illuminates. Cruise control allows you to control your speed using the switches on the steering Changing the set speed wheel.
Cruise Control Resuming the set speed E70616 Press the RES switch. The cruise control indicator illuminates and the system will attempt to resume the speed that you previously set. Switching cruise control off E70613 Press the OFF switch. The system will not retain the speed that you previously set.
Adaptive cruise control (ACC) Note: When adaptive cruise control is PRINCIPLE OF OPERATION activated, you may hear some unusual sounds during automatic braking. This is WARNINGS normal and caused by the automatic The system is not a collision warning braking system. or avoidance system.
Adaptive cruise control (ACC) Detection beam issues Automatic braking with ACC WARNINGS You must take immediate action once alerted, as the adaptive cruise control braking will not be sufficient to keep a safe distance to the vehicle in front. In some cases there may be no warning or the warning may be delayed.
Adaptive cruise control (ACC) Vehicles without speed limiter ACC gap increase ACC gap decrease Switching the system on Press switch A. The system is set to standby mode. Setting a speed Note: The system must be in standby mode. E124908 ACC on ACC cancel ACC off...
Page 187
Adaptive cruise control (ACC) Note: The gap setting is time dependant and therefore the distance will automatically adjust with your speed. For example on a gap setting of four bars, the time gap is 1.8 seconds. This will mean that at a speed of 100 km/h (62 mph), the distance to the vehicle in front will be maintained at 50 metres (164 feet).
Page 188
Adaptive cruise control (ACC) Vehicles with speed limiter Press switch A to turn the system off. Note: When deactivating the system by pressing switch A, the stored speed is not retained. Automatic deactivation E82312 Note: If the engine speed drops too low, a This is a follow mode, and the system will message is displayed in the information accelerate or decelerate as necessary to...
Adaptive cruise control (ACC) The system assists you by warning of the FORWARD ALERT FUNCTION risk of a collision with a vehicle in front. WARNINGS The system alerts you by warning chimes and a visual warning in the information Never wait for a collision warning. display.
Speed Limiter PRINCIPLE OF OPERATION WARNING When you are going downhill, your speed may increase above the set speed. The system will not apply the brakes but a warning will be given. The system allows you to set a speed, to which the vehicle then becomes limited.
Speed Limiter System warnings If the set limit is accidentally exceeded the information display will show the set speed flashing together with an audible warning chime. If the set limit is intentionally exceeded the information display will show the set speed crossed out.
Driver Alert Note: Keep the windscreen free from PRINCIPLE OF OPERATION obstructions such as bird droppings, insects and snow or ice. WARNINGS Note: The system is intended as a driver aid The system does not relieve you of when driving on fast main roads and your responsibility to drive with due motorways.
Driver Alert System display Resetting the system When active the system will run You can reset the system by either: automatically in the background and only Switching the ignition off and on. issue warnings if required. You can view Stopping the vehicle and then opening the status at any time using the and closing the driver's door.
Lane Departure Warning Note: The system is intended as a driver aid PRINCIPLE OF OPERATION when driving on fast main roads and motorways. WARNINGS Note: The system may not operate during The system does not relieve you of hard braking or acceleration and, when you your responsibility to drive with due are intentionally steering the vehicle.
Lane Departure Warning A column of lane markings is displayed either side of the vehicle graphic. The lane markings are colour coded as follows: Green - The system is ready to warn you of any unintentional lane departure. Red - The vehicle is approaching or is E131360 too close to the detected lane System on...
Load Carrying GENERAL INFORMATION CAUTIONS Do not allow items to contact the rear windows. WARNINGS Use load securing straps to an Do not use any abrasive materials to approved standard, e.g. DIN. clean the interior of the rear windows. Make sure that you secure all loose Do not install stickers or labels to the items properly.
Load Carrying SLIDING LOADSPACE FLOOR WARNING Do not slide the loadspace floor rearwards when the vehicle is standing on an incline of 15 degrees or more and facing uphill. CAUTION The maximum permissible weight on the sliding loadspace floor is 200 kilogrammes (441 pounds).
Load Carrying 4. Release the support leg from the clip on the underside of the floor. 5. Insert the end into the square retainer in the left-hand rail (3). 6. Lift the storage compartment cover using the loop. To return the loadspace floor to the normal position: Hold the floor with one hand and release the support leg with the other...
Load Carrying S-MAX Vehicles without third row seats E75395 CARGO NETS Luggage retention net - type 1 E75891 WARNING When the retention net is installed, Behind the front seats do not sit in the seats behind it. Behind the second row seats CAUTION Keep a distance of at least one centimetre (½...
Page 202
Load Carrying Installing the net E75892 E75893 Release button E75894...
Load Carrying Luggage retention net - type 2 Fold the seatbacks down. See Rear Seats (page 129). CAUTIONS 2. If the retention net is folded, press the Do not exceed the maximum red release button C on the hinges of permissible retention net load of 1 the upper and lower bar 1 and unfold kilogram (2 pounds).
Load Carrying LUGGAGE COVERS ROOF RACKS AND LOAD CARRIERS WARNING Roof rack Do not place objects on the luggage cover. WARNINGS If you use a roof rack, the fuel consumption of your vehicle will be higher and you may experience different driving characteristics.
Page 205
2. Pull the cover towards you. Note: The side mounting tracks are designed such that crossbars (for bicycle carriers, ski carriers etc.) from the Ford accessories range can be fitted. Note: Before installing the crossbars, clean the side mounting tracks with water and a sponge.
Load Carrying LOAD RETAINING FIXTURES E75002 WARNINGS Do not raise the seatback when a load retaining fixture is installed. E131374 WARNING Do not exceed the maximum permissible load of 60 kilogrammes Make sure that the clamping hook is (132 pounds) on two load retaining correctly positioned.
Page 207
Load Carrying Installing the load retaining Luggage compartment floor (vehicles fixtures with five seats) Seatback E74997 E74999 E74998...
Page 209
Load Carrying E76378 Turn the box over. 2. Position the load bracket. E75001 3. Secure the load bracket with four Installing the load bracket screws. WARNINGS Install the load bracket with the longest section towards the rear of the vehicle. If you install it the wrong way round, it may not hold the box in place in the event of an accident.
Load Carrying E76380 E75891 5. Position the load bracket onto the folded seatback so that the captured Behind the front seats bolts go through the two holes in longest section of the bracket. Behind the second row seats 6. Secure the load bracket with the two Installing the dog guard wing nuts.
Page 211
Load Carrying E75897 E75898 Fold the seatbacks down. See Rear Seats (page 129). 2. Attach the bar (C or D) to the luggage anchor points 1. See Luggage Anchor Points (page 195). Do not tighten the screws. 3. Push the ends of the bar on the grille towards each other and insert them into the retainers on the roof (A or B).
Page 212
Load Carrying E75899 Loosen the handwheel and remove it 2. Fold down the flap 5. 3. Fix the flap with the handwheel 6. 4. Route the seat belt through the opening.
Towing Change down a gear before you reach a TOWING A TRAILER steep downhill gradient. WARNINGS TOW BALL Do not exceed 100 km/h (62 mph). WARNINGS The rear tyre pressures must be When not in use, always transport increased by 0.2 bar (3 psi) above the tow ball arm securely fastened specification.
Page 214
Towing Unlocking the tow ball arm Inserting the tow ball arm mechanism E71329 Remove the protecting cap (1). Insert the key and turn it clockwise to unlock (2). 2. Hold the tow ball arm. Pull the handwheel out and turn it clockwise until it clicks (3).
Page 215
Towing Driving with a trailer Removing the tow ball arm E71331 WARNING If any of the below conditions cannot be met, do not use the tow bar and have it checked by a properly trained technician. Before starting your journey, make sure E71332 that the tow ball arm is properly locked.
Towing Driving without a trailer RETRACTABLE TOW BALL CAUTION Only move the tow ball arm with your hand. Never use your foot or auxiliary tools as damage to the mechanism may result. E94771 Remove the tow ball arm. 2. Insert the plug into its seat (1). WARNING Never unlock the tow ball arm with the trailer attached.
Page 217
Towing A 13-pin trailer socket B is provided underneath the rear bumper next to the tow ball arm C. E75175 E76040 Note: When not in use, insert the key into the storage position D to the right of the handwheel. Swivelling the tow ball in WARNINGS Keep your hands away from the...
Towing 4. Manually turn the tow ball arm steadily from its midway position to the stop in the stowage position. The tow ball arm automatically locks in the end position. The locking process is clearly audible if the level of background noise is not too high.
Page 219
Towing 4. Manually turn the tow ball arm steadily CAUTIONS from its midway position to the stop in When cleaning the vehicle with a the operating position. The tow ball steam jet do not direct the high arm automatically locks in the end pressure jet directly onto the swivel position.
Driving Hints In an emergency, the vehicle can be driven RUNNING-IN through water to a maximum depth of 200 millimetres (8 inches) and at a maximum Tyres speed of 10 km/h (6 mph). Extra caution should be exercised when driving through WARNING flowing water.
Roadside Emergencies FIRST AID KIT E73238 Space is provided in the under floor storage compartment to store a first aid kit. See Storage compartments (page 140). WARNING TRIANGLE E73239 Space is provided in the under floor storage compartment to store a warning triangle. See Storage compartments (page 140).
Fuses FUSE BOX LOCATIONS Engine compartment fuse box E72590 2. Remove the cover. 3. Turn the knob through 90 degrees and release the fuse box from the retaining bracket. E72588 4. Lower the fuse box cover and pull it Central fuse box towards you.
Fuses CHANGING A FUSE CAUTION Fit a replacement fuse with the same WARNINGS rating as the one you have removed. Do not modify the electrical system of your vehicle in any way. Have Note: You can identify a blown fuse by a repairs to the electrical system and break in the filament.
Fuses Fuse Ampere rating Circuits protected FLR (Start Stop) Fit a replacement with the same rating as the one you have removed. Central fuse box E124888 Left-hand drive Right-hand drive...
Vehicle recovery Front towing eye TOWING POINTS Towing eye location E73241 Rear towing eye E73240 The screw-in towing eye is located in the underfloor storage compartment behind the front seats. See Storage compartments (page 140). The towing eye must always be carried in the vehicle.
Vehicle recovery Vehicles with 2.0L Duratorq-TDCi WARNINGS (DW) Diesel (Stage V) or 2.0L The brake servo and the power EcoBoost SCTi (MI4) and 6-Speed steering pump do not operate unless Automatic Transmission the engine is running. Press the brake pedal harder and allow for increased CAUTIONS stopping distances and heavier steering.
Have your vehicle serviced regularly to help (page 244). maintain its roadworthiness and resale Brake fluid level. See Brake and value. There is a large network of Ford Clutch Fluid Check (page 245). Authorised Repairers that are there to help you with their professional servicing Washer fluid level.
Page 236
Maintenance E87785 Raise the bonnet slightly and move the E87786 catch towards the left-hand side of the Open the bonnet and support it with the vehicle. strut. Closing the bonnet WARNING Make sure that the bonnet is closed properly. Lower the bonnet and allow it to drop from under its own weight for the last 20 –...
Maintenance Power steering fluid reservoir. See Power Steering Fluid Check (page 245). Engine coolant reservoir. See Engine Coolant Check (page 244). The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 2.0L DURATEC-HE (MI4) E73231 Brake and clutch fluid reservoir (right-hand drive).
Maintenance Power steering fluid reservoir. See Power Steering Fluid Check (page 245). Engine coolant reservoir. See Engine Coolant Check (page 244). The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 2.0L ECOBOOST SCTI (MI4) E124921 Brake and clutch fluid reservoir (right-hand drive).
Maintenance Power steering fluid reservoir. See Power Steering Fluid Check (page 245). Engine coolant reservoir. See Engine Coolant Check (page 244). The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 2.3L DURATEC-HE (MI4) E81313 Brake and clutch fluid reservoir (right-hand drive).
Maintenance Power steering fluid reservoir. See Power Steering Fluid Check (page 245). Engine coolant reservoir. See Engine Coolant Check (page 244). The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 1.6L DURATORQ-TDCI (DV) DIESEL E135199 Brake and clutch fluid reservoir (right-hand drive).
Maintenance Engine oil dipstick . See Engine Oil Check (page 244). Power steering fluid reservoir. See Power Steering Fluid Check (page 245). Engine coolant reservoir. See Engine Coolant Check (page 244). The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 2.0L DURATORQ-TDCI (DW) DIESEL E73234...
Page 243
Maintenance E124913 Brake and clutch fluid reservoir (right-hand drive). See Brake and Clutch Fluid Check (page 245). Engine oil filler cap . See Engine Oil Check (page 244). Brake and clutch fluid reservoir (left-hand drive). See Brake and Clutch Fluid Check (page 245).
Do not top up further than the MAX CAUTION mark. Do not use oil additives or other engine treatments. Under certain Top up with fluid that meets the Ford conditions, they could damage the specification. See Technical engine. Specifications (page 246).
Note: The brake and the clutch systems are CAUTIONS supplied from the same reservoir. In an emergency, you can add just Top up with fluid that meets the Ford water to the cooling system to reach specification. See Technical a vehicle service station. Have the Specifications (page 246).
Brake fluid Fluid Your engine has been designed to be used with Castrol and Ford Engine Oil, which gives a fuel economy benefit whilst maintaining the durability of your engine. Topping up the oil: If you are unable to find an oil that meets the specification defined by WSS-M2C913-C, you must use SAE 5W-30 that meets the specification defined by ACEA A5/B5.
Page 249
Maintenance Variant Item Capacity in Litres (gallons) Windscreen washer system 3.9 (0.9) Fuel tank 70 (15.4) Engine lubrication system - 1.6L EcoBoost SCTi (Sigma) 4.1 (0.9) including the oil filter Engine lubrication system - 1.6L EcoBoost SCTi (Sigma) 3.8 (0.8) excluding the oil filter 1.6L EcoBoost SCTi (Sigma) Engine cooling system...
Page 250
Maintenance Variant Item Capacity in Litres (gallons) 2.0L Duratorq-TDCi Engine cooling system 8.1 (1.8) Engine lubrication system - 2.2L Duratorq-TDCi 6 (1.3) including the oil filter Engine lubrication system - 2.2L Duratorq-TDCi 5.4 (1.2) excluding the oil filter 2.2L Duratorq-TDCi Engine cooling system 8.4 (1.9)
Vehicle Care Cleaning the chrome trim CLEANING THE EXTERIOR CAUTION WARNING Do not use abrasives or chemical If you use a car wash with a waxing solvents. Use soapy water. cycle, make sure that you remove the wax from the windscreen. Body paintwork preservation CAUTIONS CAUTIONS...
You should repair paintwork damage caused by stones from the road or minor scratches as soon as possible. A choice of products is available from your Ford Dealer. Read and follow the manufacturer’s instructions.
Vehicle battery To connect the booster cables JUMP-STARTING THE VEHICLE WARNING Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. CAUTIONS Connect batteries with only the same nominal voltage. Always use booster cables with insulated clamps and adequate size cable.
Vehicle battery BATTERY CONNECTION CAUTIONS Do not connect to the negative (–) POINTS terminal of the flat battery. Make sure that the cables are clear of any moving parts and fuel delivery system parts. To start the engine Run the engine of vehicle B at moderately high speed.
Wheels and Tyres Jacking and lifting points GENERAL INFORMATION WARNING CAUTIONS Never place anything between the Use only approved wheel and tyre jack and the ground, or the jack and sizes. Using other sizes could damage the vehicle. the vehicle and will make the National Type Approval invalid.
Wheels and Tyres Indentations in the sills A show the WARNINGS location of the jacking points. Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead. Switch off the ignition and apply the parking brake. If your vehicle has a manual transmission, select first or reverse gear.
Page 257
Wheels and Tyres Note: The wheel nuts of alloy wheels and spoked steel wheels can also be used for the steel spare wheel for a short time (maximum two weeks). Note: You can use wheel nuts designed for use with alloy wheels with steel wheels. Note: Make sure the wheel and hub contact surfaces are free from foreign matter.
Wheels and Tyres General information WARNINGS Depending on the type and extent of tyre damage, some tyres can only be partially sealed or not sealed at all. Loss of tyre pressure can affect vehicle handling, leading to loss of vehicle control. Do not use the tyre repair kit if the tyre has already been damaged as a result of being driven under inflated.
Page 259
Wheels and Tyres Using the tyre repair kit Inflating the tyre WARNINGS WARNINGS Compressed air can act as an Check the sidewall of the tyre prior explosive or propellant. to inflation. If there are any cracks, bumps or similar damage, do not Never leave the tyre repair kit attempt to inflate the tyre.
Page 260
Wheels and Tyres Open the lid of the tyre repair kit. 2. Peel off the label I showing the maximum permissible speed of 80 km/h (50 mph) from the casing and attach it to the instrument panel in the driver’s field of view. Make sure the label does not obscure anything important.
Page 261
Wheels and Tyres Make sure the kit, the bottle lid and 6. Once you have inflated the tyre to its the orange cap are stored safely, but correct tyre pressure, move the still easily accessible in the vehicle. compressor switch H to position 0, The kit will be required again when remove the power plug G from the you check the tyre pressure.
Wheels and Tyres TYRE CARE USING SNOW CHAINS WARNINGS Do not exceed 50 km/h (30 mph). Do not use snow chains on snow-free roads. Only fit snow chains to specified tyres. See Technical Specifications (page 262). E70415 CAUTION To make sure the front and rear tyres of your vehicle wear evenly and last longer, If your vehicle is fitted with wheel we recommend that you swap the tyres...
Page 263
Wheels and Tyres Note: Type 3 instrument clusters have a WARNINGS slightly different menu structure. Select The system may take longer to Settings first to access Information. detect low pressure in the tyres if you have fitted snow chains. Press the right arrow button on the steering wheel to enter the main menu.
Wheels and Tyres TECHNICAL SPECIFICATIONS Wheel nut torque Wheel type Nm (Ib-ft) 170 (125) Tyre pressures (cold tyres) Up to 160 km/h (100 mph) Normal load Full load Front Rear Front Rear Variant Tyre size bar (lbf/ bar (lbf/ bar (lbf/ bar (lbf/ in²) in²)
Page 265
Wheels and Tyres Normal load Full load Front Rear Front Rear Variant Tyre size bar (lbf/ bar (lbf/ bar (lbf/ bar (lbf/ in²) in²) in²) in²) 2.0L Duratec-HE 225/50 R 17 and (MI4) and 2.3L 2.2 (32) 2.2 (32) 2.6 (38) 3.1 (45) 235/45 R 18 Duratec-HE (MI4)
Page 266
Wheels and Tyres Normal load Full load Front Rear Front Rear Variant Tyre size bar (lbf/ bar (lbf/ bar (lbf/ bar (lbf/ in²) in²) in²) in²) 2.0L EcoBoost SCTi (MI4) and 2.2L 225/50 R 17 and 2.6 (38) 2.6 (38) 2.8 (41) 3.4 (49) Duratorq-TDCi...
Vehicle identification Note: The vehicle identification plate VEHICLE IDENTIFICATION design may vary to that shown. PLATE Note: The information shown on the vehicle identification plate is dependant upon market requirements. E135662 Model Variant Engine designation Emission level Vehicle identification number Gross vehicle weight Gross train weight Maximum front axle weight...
Vehicle identification VEHICLE IDENTIFICATION NUMBER E87496 The vehicle identification number is stamped into the floor panel on the right-hand side, beside the front seat. It is also shown on the left-hand side of the instrument panel.
Capacities and Specifications Towing equipment dimensions S-MAX E75182 Item Dimension description Dimension in mm (inches) Bumper – end of tow ball 102 (4) Attachment point – centre of tow ball 16 (0.63) Wheel centre – centre of tow ball 1 079 (42.48) Centre of tow ball –...
Page 271
Dimension in mm (inches) Centre of tow ball – centre 2. attachment 424 (16.69) point Centre of tow ball – centre 3. attachment 636 (25.04) point Galaxy E75181 Item Dimension description Dimension in mm (inches) Bumper – end of tow ball 101 (3.98) Attachment point –...
Page 272
Capacities and Specifications Item Dimension description Dimension in mm (inches) Centre of tow ball – side member 438 (17.2) Inner side of side member 876 (34.5) Centre of tow ball – centre 1. attachment 412 (16.22) point Centre of tow ball – centre 2. attachment 473 (18.62) point Centre of tow ball –...
Audio introduction IMPORTANT AUDIO INFORMATION WARNINGS Due to technical incompatibility, E66257 recordable (CD-R) and rewritable Disc labels (CD-RW) discs may not function correctly. Audio CD These units will play compact discs that conform to the International Red Book standard audio specification.
Audio unit overview 6000CD E138368 CD aperture. See Loading compact discs (page 286). On, off and volume control. See On/off control (page 277). CD eject. See Ejecting compact discs (page 289). Clock. See Setting the clock and date on the audio unit (page 276). Balance and fade control.
Page 275
Audio unit overview Sony CD and Sony CD DAB E138370 Scan. See Station tuning control (page 281). See Compact disc track scanning (page 288). Information. See Audio unit operation (page 277). See Audio unit menus (page 283). See Compact disc player (page 286). See Audio troubleshooting (page 292).
Page 276
Audio unit overview Tone. See Bass/treble control (page 277). Phone menu. See Telephone (page 293). Radio and waveband select. See Waveband button (page 279). Auxiliary and CD select. See Auxiliary input (AUX IN) socket (page 291). See Compact disc player (page 286). CD eject.
Audio system security The number of attempts will be shown in SECURITY CODE the display. Each unit incorporates a unique code that If the display reverts to CODE another must be entered before the unit will entry attempt may be made immediately. operate.
Audio unit clock and date displays Sony and Sony DAB SETTING THE CLOCK AND DATE ON THE AUDIO UNIT Changing the date and time Press the CLOCK button. 6000CD 2. Press the left or right navigation button Changing the date and time until the date or time value that you wish to change flashes in the display.
Audio unit operation ON/OFF CONTROL BALANCE/FADE CONTROL Press the on/off control. This will also The balance function is used to adjust the operate the unit for up to one hour with the sound distribution between the left and ignition turned off. right speakers.
Page 280
Audio unit operation 6000CD Menu functions First level Second level During radio recep- During tape playback During CD playback During all functions tion Manual tuning 12/24 hour Scan Traffic local or distant Scan tuning Shuffle 12/24 hour ADV menu Repeat Comp News ADV menu...
Audio unit operation Menu functions During radio reception During CD playback volume volume Traffic local or distant Traffic local or distant Regional ON/OFF Shuffle Repeat Comp ON/OFF Note: The sequence in which functions appear may vary for different audio units and vehicles.
Audio unit operation TP will be shown within a box in the display AUTOSTORE CONTROL when you are tuned to a station providing traffic information from a linked RDS (radio Note: This function will overwrite the data system) or EON (enhanced other previously stored autostore preset stations.
Audio unit operation Ending traffic announcements 3. Press the seek up or seek down button to select either local (TA LOCAL) or The audio unit will return to normal distant (TA DIST) traffic operation at the end of each traffic announcements.
Page 284
Audio unit operation Sony CD Sony and Sony DAB Select a waveband and briefly press the Press the SCAN button. SCAN flashes up or down navigation button. The unit will or SCANNING is shown in the display. stop at the first station it finds in the 2.
Audio unit menus Changing the DSP settings AUTOMATIC VOLUME CONTROL Press the DSP button once for occupancy and twice for equaliser. For When available, automatic volume control item location: See Audio unit (AVC) adjusts the volume level to overview (page 272). compensate for engine noise and road 2.
Audio unit menus 3. Using the seek up or seek down button ALTERNATIVE FREQUENCIES select the required setting. Many programmes broadcast on the FM 4. Press the MENU button or allow the waveband have a programme system to time out to confirm your identification (PI) code, which can be selection.
Audio unit menus 3. Using the seek up or seek down button 3. Press the button between the turn the function on or off. navigation buttons to make your selection. 4. Press the MENU button or allow the system to time out to confirm your 4.
Compact disc player LOADING COMPACT DISCS LOADING THE COMPACT DISC CHANGER 6000CD, Sony and Sony DAB CAUTIONS Always check that the CD aperture is empty before inserting a CD. Do not insert more than one disc into each slot. Insert a CD, label side up, into the audio unit.
Compact disc player Compact disc changer playback UNLOADING THE COMPACT DISC CHANGER 6000CD Press the CD button twice to start CD CAUTION playback. Keep the door closed when the Note: If the CD button is pressed when no magazine is installed. discs are loaded, NO CDS will be shown in the display.
Compact disc player Sony and Sony DAB Press the MENU button repeatedly until SHUF is shown in the display. Press the MENU button. 2. Using the seek up or seek down button 2. Using the up or down navigation button scroll through the display until SHUF scroll through the display until COMP ALL or SHUFF CD is shown in the...
Compact disc player Sony and Sony DAB Press the SCAN button once to scan each track on an audio CD, or the first Press the MENU button. 10 seconds of each track on each folder of a MP3 CD. 2. using the up or down navigation buttons scroll through the display until 2.
Compact disc player When the playback of a file is finished the ENDING COMPACT DISC playback of the other files in the same PLAYBACK directory continues. Directory change takes place automatically when all files in the All except Sony and Sony DAB current directory have been played back.
Auxiliary input (AUX IN) socket Note: For optimum performance when using any auxiliary device set the volume on the device high. This will reduce audio interference when charging the device via the vehicle power supply socket. When fitted the Auxiliary input (AUX IN) socket permits an auxiliary device, such as an MP3 player, to be linked into the vehicle audio system.
Audio troubleshooting Audio unit display Rectification General error message for CD fault conditions, for example cannot read the CD, data-CD inserted. May CD ERROR also indicate a audio unit malfunction. Make sure that PLEASE CHECK CD the disc is correctly loaded, clean and re- load the CD CDC ERROR or replace the CD with a known music CD.
Compatibility of phones 2. In the Bluetooth menu on your phone, CAUTION search for Ford Audio and select it. As no common agreement exists, 3. Enter the code number shown on the mobile phone manufacturers are able vehicle display using the phone keypad.
Telephone Phonebook categories Select the phone from the active phone menu. Depending on your phonebook entry, Turning the ignition and radio or navigation different categories can be displayed in unit back on again, the last active phone the audio unit. is picked up by the system.
Telephone Note: Some audio units have the accept 5. Press the PHONE or the call accept and reject buttons on the front bezel. These button to dial the selected phone operate in the same way. number. Dialling a number using the address USING THE TELEPHONE - book - Sony radio VEHICLES WITHOUT:...
Page 298
Telephone Receiving an incoming call Audio units without a telephone keypad can also end a call by pressing either Accepting an incoming call PHONE, CD, AM/FM or ON/OFF, or by pressing the MODE button on the remote Incoming calls can be accepted by pressing control either the call accept button, the PHONE button or the MODE button on the remote...
Telephone Audio units with green call accept Press the PHONE or call accept button button. 2. Press the MENU button on the audio Press the call accept button. Press the unit. button once again to turn this function off. 3. Select the DEBOND option on the Audio units without green call accept audio unit.
Page 300
Telephone Making a call Accepting a second incoming call Second incoming calls can be accepted Dialling a number by pressing either the call accept button, Phone numbers can be dialled using voice the MODE button on the remote control, control. See Voice control (page 300). the PHONE button on the unit or by using the ACCEPT option in the menu.
Page 301
Telephone Debonding a bonded phone A bonded phone can be deleted from the system at any time, unless a phone call is in progress. Press the PHONE button on the unit. 2. Select the BT SETTINGS option in the menu. 3.
Voice control Do not try to give any commands until the PRINCIPLE OF OPERATION beep tone has been heard. The voice control system will repeat each spoken CAUTION command back to you. Using the system with the engine off If you are not sure how to continue say will drain the battery.
Voice control Name tag automatic climate control: "TEMPERATURE", "AUTO MODE", The name tag functionality can support "DEFROSTING/DEMISTING ON" and the phone, audio and navigation features "DEFROSTING/DEMISTING OFF" by using the "STORE NAME" function. You radio: "TUNE NAME" can assign name tags to items such as external device (USB): "TRACK"...
Voice control "CD PLAYER" "REPEAT OFF" * Can be used as a shortcut. ** Only available if the CD contains audio data files like MP3 or WMA. Track You can choose a track on your CD directly. Steps User says System answer "CD PLAYER"...
Page 305
Voice control "CD CHANGER" "PLAY" "DISC" "TRACK" "SHUFFLE ALL" "SHUFFLE CD" "SHUFFLE FOLDER" "SHUFFLE OFF" "REPEAT CD" "REPEAT FOLDER" "REPEAT TRACK" "REPEAT OFF" * Can be used as a shortcut. ** Only available if the CD contains audio data files like MP3 or WMA. Disc If you have a CD changer you can choose the disc number.
Page 306
Voice control Steps User says System answer "CD CHANGER" "CD CHANGER" "TRACK NUMBER PLEASE" "TRACK" "TRACK <number>" "<a number between 1 and 99>" * Can be used as a shortcut. ** Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5"...
Page 307
Voice control "RADIO" "PLAY" * Can be used as a shortcut. Tune frequency This function allows you to tune your radio by voice commands. Steps User says System answer "RADIO" "RADIO" "AM" "AM FREQUENCY PLEASE" "FM" "FM FREQUENCY PLEASE" "TUNE <frequency>" "<frequency>"...
Page 308
Voice control Tune name This function allows you to call up a stored radio station. Steps User says System answer "RADIO" "RADIO" "NAME PLEASE" "TUNE NAME" "<name>" "TUNE <name>" * Can be used as a shortcut. Delete name This function allows you to delete a stored radio station.
Page 309
Voice control Steps User says System answer "RADIO" "RADIO" "DELETE DIRECTORY" "DELETE DIRECTORY" "CONFIRM YES OR NO" "YES" "RADIO DIRECTORY DELETED" "NO" "COMMAND CANCELLED" Play This function switches the audio source to the radio mode. Steps User says System answer "RADIO"...
Page 310
Voice control "EXTERNAL DEVICE", "USB" "PLAY" "TRACK" "PLAYLIST" "FOLDER" "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE PLAYLIST" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT FOLDER" "REPEAT OFF" * Can be used as a shortcut. ** Playlists and folders activated by voice control must be assigned special filenames. See General Information (page 318).
Page 311
Voice control Steps User says System answer "EXTERNAL DEVICE" "EXTERNAL DEVICE" "USB" "USB" "TRACK" "TRACK NUMBER PLEASE" "TRACK <number>" "<a number between 1 and 99>" * Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5"...
Voice control iPod Track You can choose a track off the all titles list of your iPod directly. Steps User says System answer "EXTERNAL DEVICE" "EXTERNAL DEVICE" "IPOD" "IPOD" "TRACK NUMBER PLEASE" "TRACK" "TRACK <number>" "<a number between 1 and 99>" * Can be used as a shortcut.
Page 313
Voice control "PHONE" "HELP" "MOBILE NAME" "DIAL NUMBER" "DIAL NAME" "DELETE NAME" "DELETE DIRECTORY" "PLAY DIRECTORY" "STORE NAME" "REDIAL" "ACCEPT CALLS" "REJECT CALLS" * Can be used as a shortcut. Phone functions Dial number Phone numbers can be dialled after giving the name tag voice command.
Page 314
Voice control Dial name Phone numbers can be dialled after giving the name tag voice command. Steps User says System answer "PHONE" "PHONE" "NAME PLEASE" "DIAL NAME" "<name>" "DIAL <name>" "CONFIRM YES OR NO" "YES" "DIALLING" "NO" "COMMAND CANCELLED" * Can be used as a shortcut. Redial This function allows you to redial the last dialled phone number.
Page 315
Voice control DTMF (Tone dialling) Note: DTMF can only be used during an ongoing call. Operate the VOICE button and This function transfers spoken numbers wait for the system prompt. into DTMF tones. For example, to make a Can only be used with vehicles installed with remote enquiry to your home answering a dedicated VOICE button.
Page 316
Voice control Steps User says System answer "PHONE" "PHONE" "DELETE NAME" "NAME PLEASE" "<name>" "DELETE <name>" "CONFIRM YES OR NO" "YES" "<name> DELETED" "NO" "COMMAND CANCELLED" Play directory Use this function to let the system tell you all stored entries. Steps User says System answer...
Voice control Steps User says System answer "PHONE" "PHONE" "REJECT CALLS" "REJECT CALLS" "ACCEPT CALLS" "ACCEPT CALLS" * use this command to turn the reject mode off Overview NAVIGATION SYSTEM The overview below shows the available COMMANDS voice commands. The following lists will give further information about the Please refer to your separate Navigation complete command menu in selected...
Page 318
Voice control This function allows you to adjust the fan speed. Steps User says System answer "CLIMATE" "CLIMATE" "FAN SPEED PLEASE" "‘FAN" "MINIMUM" "FAN MINIMUM" "<a number between 1 and 7>" "FAN <number>" "MAXIMUM" "FAN MAXIMUM" * Can be used as a shortcut. On vehicles fitted with an English language module the "FAN" shortcut is not available.
Page 319
Voice control Steps User says System answer "MAXIMUM" "TEMPERATURE MAXIMUM" * Can be used as a shortcut. Auto mode Steps User says System answer "CLIMATE" "CLIMATE" "AUTO MODE" "AUTO MODE" * Can be used as a shortcut. Can be deactivated by selecting a different temperature or fan speed.
Cover the socket connection when not in use. iPod media players (refer to Only use USB Mass-Storage device www.ford-mobile compliant devices. -connectivity.com for latest compatibility list). Always switch your audio unit to a different source (for example the The system is USB 2.0 full speed...
Plug in the device, and if necessary secure below: it to prevent movement within the vehicle. Create folders named with the structure "Ford<*>" where <*> is a Connecting an iPod number 1-10. For example "Ford3" For optimum convenience and audio without an extension.
Connectivity Bonding the device Information not available Note: Some audio and navigation units E100028 have a separate Bluetooth audio menu. Use this to access setup and control. Sony radio To connect the device to the system follow Operation the same procedure as for Bluetooth hands free phones.
Page 323
Connectivity Audio control The display will show the track information, together with other important Press the left and right arrow keys to skip information described below: backwards and forwards through tracks. A vertical scroll bar on the right side of Press and hold the left/right arrow keys to the display shows the current position enable fast rewind/fast forward through...
Connectivity Press the INFO button to display the "<" to the left hand side of the display following: indicates that a further level up is readable. filename Icons to the left of track/folder text title indicate the type of file/folder. Refer artist to the list for an explanation of these album...
Page 325
Connectivity iPod is the active source The display will show the track information, together with other important information described below: E100030 iPod playlist A vertical scroll bar on the right side of the display shows the current position E100031 of the list view. iPod artist ">"...
Page 326
Connectivity Press the INFO button to display the To navigate the iPod contents, use the following: rotary scroll/select button to browse through lists. Push the button to expand title the contents within the highlighted playlist, artist album, artist, genre or to commence track number and playing time.
Page 327
Connectivity The iPod menu list for browsing contents Press the SCAN button to scan the will be available through the display. currently selected tracks. Navigation of the contents follows the Press the INFO button to display the same principles as for iPod standalone use following: (for example search by artist, title, etc.).
Read and follow all stated safety precautions. Failure to do so may increase your risk of collision and personal injury. Ford Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines.
GPS receiver. system performance. To avoid this situation, only recommended phones Note: The Ford Mobile Navigation must be should be used. installed and activated on your mobile phone. Please visit the website Note: It is possible to activate up to a www.ford-mobile-connectivity.com for...
Navigation system E114213 2. Switch your mobile phone on and start the "Ford Mobile Navigation". 3. Choose "Select Destination". 4. Choose "Enter Address". 5. Change route options if necessary and start the route guidance. 6. The vehicle display will show the turn information.
The Bluetooth word mark and logos are FCC/INDUSTRY CANADA NOTICE owned by the Bluetooth SIG, Inc. and any use of such marks by Ford Motor Company This device complies with Part 15 of the is under license. Other trademarks and FCC Rules.
Appendices E114220 Certificate for United Arab Emirates TYPE APPROVALS EU Declaration Hereby, Valeo declares that this short range device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. E125209...
Appendices ELECTROMAGNETIC WARNINGS The RF (radio frequency) transmitter COMPATIBILITY equipment (e.g. cellular telephones, amateur radio transmitters etc.) may WARNINGS only be fitted to your vehicle if they comply Your vehicle has been tested and with the parameters shown in the table certified to legislations relating to below.
Page 334
Appendices Frequency Band Maximum output power Watt (Peak Antenna Positions RMS) 142 – 176 50 W 1, 2, 3 380 – 512 50 W 1, 2, 3 806 – 940 10 W 1, 2, 3 1200 – 1400 10 W 1, 2, 3 1710 –...
Page 335
Index Ashtray.............138 Front ashtray............138 Rear ashtray............138 At a Glance............10 See: Climate Control...........112 Adjusting the steering wheel......14 About This Manual...........7 Autolamps...............15 Automatic climate control.........17 See: Brakes............166 Automatic main beam control......15 ABS driving hints Automatic transmission........19 See: Hints on Driving With Anti-Lock Autowipers...............14 Brakes..............166 Blind spot information system (BLIS)..16...
Page 336
Auto-Dimming Mirror........79 Remote starting...........122 Autolamps............57 Auxiliary input (AUX IN) socket....144 Automatic Climate Control......115 Auxiliary Power Points........138 Air distribution............117 Galaxy..............139 Blower...............117 S-Max..............139 Mono mode............117 Rear air conditioning (triple-zone automatic climate control)..........118 Balance/fade control........277 Recirculated air.............118 Setting the temperature........116 All except Sony and Sony DAB .....277...
Page 337
Climate control commands.....315 Luggage compartment lamp and tailgate lamp..............73 Climate..............315 Clock..............137 Number plate lamp..........71 Coded keys............45 Reading lamps............72 Rear lamp (Galaxy)..........69 Cold Weather Precautions......218 Compact disc playback......287 Rear lamps (S-MAX)..........68 Side repeater............66 6000CD..............287 Vanity mirror lamp..........72 Compact disc changer playback....287 Changing a Fuse..........221...
Page 338
Index Connectivity............318 Ejecting compact discs......289 General Information..........318 6000CD..............289 Convenience features.........136 Sony CD..............289 Coolant Check Electric exterior mirrors.........77 See: Engine Coolant Check......244 Electric folding mirrors........78 Cruise Control..........180 Mirror tilting positions..........77 Principle of Operation........180 Reverse mirror dipping........78 Cruise control Electric Parking Brake........167 See: Using Cruise Control.......180 Applying the EPB..........167 Cup Holders............139...
Page 339
Index Gearbox See: Transmission..........163 General Information on Radio Fastening the seat belts.......31 Frequencies...........35 Second row centre seat belt......31 Getting started..........327 Fast forward/reverse........287 Activating the mobile phone navigation All except Sony and Sony DAB.....287 system...............327 Sony and Sony DAB..........287 Compatibility of phones........327 First Aid Kit............219 Installing the micro SD card......327 Floor Mats............144...
Page 340
Index Interior Lamps..........62 See: Hill Start Assist..........171 Courtesy lamp............62 See: Using hill start assist.........171 LED interior lighting..........63 Reading lamps............62 Vanity mirror lamps..........63 Introduction............7 Ignition Switch..........145 iPod connection Immobiliser See: Connecting an external device....319 See: Engine immobiliser........45 See: Connecting an external device - Vehicles Important audio information....271 With: Bluetooth..........319 iPod...
Page 341
Luggage compartment lid........40 Reprogramming the unlocking Playing a multi session disc......289 function..............40 Locks..............38 Lost security code........275 Luggage Anchor Points......195 Navigation introduction......326 Navigation system commands....315 Galaxy..............195 Navigation system........327 S-MAX..............196 Luggage Covers..........202 News broadcasts.........285 All except Sony and Sony DAB.....285 Sony and Sony DAB..........285...
Page 342
Rear Quarter Windows.........79 Look for the Ford logo on the following Electric rear quarter windows......80 parts ...............8 Manual rear quarter windows......79 Now you can be sure that your Ford parts Rear Seats............129 are Ford parts............7 Creating a level load floor........133 Personalised Settings........100 Second row seats..........129...
Page 343
Security code..........275 Under floor storage compartment....141 Setting the clock and date on the audio Under seat storage compartment....140 unit..............276 Sun Shades.............136 6000CD..............276 Roof (Galaxy)............136 Sony and Sony DAB..........276 Roof (S-MAX)............136 Shuffle/random..........287 Side windows............136 Switching Off the Engine......150 6000CD..............287 Sony CD and Sony CD DAB......288 Vehicles with a turbocharger......150...
Page 344
Index Telephone commands.......310 Traffic information control......280 Create a phonebook..........313 Activating traffic announcements....280 Main settings............314 Ending traffic announcements......281 Phone..............310 Local or distant traffic........280 Phone functions...........311 To adjust the preset volume......281 Telephone controls........294 Traffic announcement volume......281 Transmission..........163 Remote control..........294 Telephone setup..........293 Trip Computer..........98 Bond another Bluetooth phone....294 Average fuel consumption.......98 Making a phone an active phone....294...
Page 345
Index Under Bonnet Overview - 2.2L Using lane departure warning....192 Duratorq-TDCi (DW) Diesel....242 Setting the steering wheel vibration Under Bonnet Overview - 2.3L level..............193 Duratec-HE (MI4)........238 Setting the system sensitivity......193 Unloading the compact disc Switching the system on and off....192 changer............287 System warnings..........193 USB port............144...
Page 346
Index Using voice control........300 Name tag...............301 System operation..........300 Warning Lamps and Indicators....85 Using Winter Tyres........260 ABS warning lamp..........85 Airbag warning lamp..........85 Blind spot monitor indicator......85 Brake system lamp..........85 Vehicle battery..........251 Coolant temperature warning lamp.....85 Vehicle Care...........249 Direction indicators..........86 Vehicle Identification Number....266 Electric parking brake (EPB) warning Vehicle Identification Plate......265 lamp..............86...