Setting The System Through The Display Window - JVC SP-PWV70 Instructions Manual

Setting the system through the display window

You can adjust the sound and speaker settings of this system through the display window.
• You can adjust the sound setting of front speakers ("BAL," "BASS," and "TREBLE") for each source.
• The adjustments of the speaker size, speaker distance, "LFE ATT," "CROSS," and "D. COMP" take effect for all sources.
IMPORTANT:
When using the remote control, check to see if
its remote control mode selector is set to the
correct position:
To operate this system, set it to "AUDIO/TV/
VCR."
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
cancelled before you finish, start from step 1 again.
• When selecting DVD, AUX, or AUX DIGITAL as the source, the
settings of the corresponding items in the choice menus also
change.
From the remote control ONLY:
VCR
–
TV
–
SLEEP
–
SETTING
SETTING
TV RETURN
button
ON
SCREEN
CHOICE
TV VOL CHANNEL
TV/VIDEO
1
/REW
DOWN
1 Press SETTING.
The item you last selected appears on the display
window.
Example: "BAL" has been selected.
L R
2 Press Cursor ∞/5 repeatedly to select the
item you want to set.
Each time you press the button, the items shown on the
display window change as follows:
" BAL " BASS " TREBLE " FRNT SP
" CNTR SP " REAR SP " FRNT D " CNTR D
" REAR D " CROSS " LFE ATT. " D.COMP
" (back to the beginning)
AUDIO/
TV/VCR
CATV/DBS
1 2 3
+
CENTER TEST
4 5 6
+
REAR-L
7 8 9
+
REAR-R
0 +10
10
FM MODE 100+
AUDIO/
TV/VCR
CATV/DBS
Cursor and
ENTER
SURROUND
MODE
ENTER buttons
VOLUME
MUTING
¡
PLAY FF/
TUNING UP
See the corresponding pages for the detail of adjustments.
• BAL (Balance):
Adjust the balance between the left and right front
speakers. (See page 59.)
• BASS, TREBLE:
Adjust the enhancement level for bass or treble sound
from the front speakers. (See page 59.)
• FRNT SP (front speakers),
CNTR SP (center speaker),
REAR SP (rear speakers):
Select the size of each speaker. (See page 60.)
• FRNT D (front speakers distance),
CNTR D (center speaker distance),
REAR D (rear speakers distance):
Set the distance from the listening position to the
speakers. (See page 61.)
• CROSS (CROSS OVER):
Select the cutoff frequency of the subwoofer according
to the front speakers used with this system.
(See page 60.)
• LFE ATT.:
Diminish the distortion of the bass sound from the
subwoofer while playing back a disc with Dolby Digital
or DTS Digital Surround. (See page 59.)
• D.COMP (D. RANGE COMPRESSION):
Enjoy a powerful sound at night even at a low volume
level when listening to the sound with Dolby Digital.
(See page 59.)
3 Press Cursor 2/3 to make an adjustment.
Example:
L R
• BAL:
"L–21" to "L–1" " "CENTER" " "R–1" to "R–21"
• BASS, TREBLE:
Within the range between –10 to +10 (by 2 step)
• FRNT SP, CNTR SP, REAR SP:
"SML" (small) " "LRG" (large) " "NO" (none)
("NO" is not selectable for the front speakers.)
• FRNT D, CNTR D, REAR D:
Within the range between 0.3 m and 9.0 m. (by 0.3 m
step)
• CROSS:
"200 Hz" " "150 Hz" " "120 Hz" " "100 Hz"
" "80 Hz"
• LFE ATT.:
"ON" " "OFF"
• D.COMP:
"MID" " "MAX" " "OFF"
4 Repeat steps 2 and 3 to set other items.
NOTES:
• If you have selected "SML" for the front speakers, you cannot select
"LRG" for the center and rear speakers.
• You can confirm your adjustment of speaker settings by listening to
the test tone. To output the test tone, press SOUND, then TEST.
(See page 35.)
66