EU Declaration of Conformity EU Declaration of Conformity EU Übereinstimmugserklärung Déclaration de conformité UE Declaración de conformidad de la UE Dichiarazione di conformità UE EU Försäkran om Överensstämmelse Declares, that the product: conforms to the following Standards: Erklärt, daß das Produkt: folgenden Normen entspricht: Déclarent que le produit cité...
Informations complérnentaires: “Ce produit est conforme aux exigences de la directive sur les basses tensions 73/23/ CEE et de la directive EMC 89/336/CEE.” Información complementaria: “El Producto cumple los requistos de baja tensión de la Directiva 73/23/CEE y la Directiva EMC 89/336/CEE.” Ulteriori informazioni: “Il prodotto é...
Page 4
NOTE: If this product is supplied with a network port, please refer to the paragraph «Network connection». Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of Corporation. The consequences of the use of this product in non-approved working environments maybe: •...
Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference.
Conformity Statement The equipment has been approved to [Commission Decision CTR21 ] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries the approval does nod of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Type of service Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
Disconnection If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change. Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission,...
Page 9
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
Notes for Users in Australia & New Zealand Modem warning notice for Australia Modems connected to the Australian telecom network must have a valid Austell permit. This modem has been designed to specifically configure to ensure compliance with Austell standards when the country selection is set to Australia.
Notes for use of this device in New Zealand • The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation, which is only one of many ways of delivering high quality voice telephony to customers.
Page 12
c/ Automatic calls to different numbers shall be not less than 5 seconds apart. • Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair. • The correct settings for use with this modem in New Zealand are as follows: ATB0 (CCITT operation) AT&G2 (1800 Hz guard tone)
Number to be dialed: 0 1 2 3 4 5 6 7 8 9 Number to program into computer: 0 9 8 7 6 5 4 3 2 1 Note that where DTMF dialing is used, the numbers should be entered normally.
Page 14
The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network. The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100.
Page 15
FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for...
Page 17
VCCI Notice (Japan Only) Class BITE This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Page 18
2. DGT Label illustrstion 3. The following is the statement that should be printed in user manual.
Page 19
FCC Class B Digital Devices & Peripheral Devices (Declaration of Conformity or Certification Authorization) Declaration of Conformity Label & Marking Requirements • User Manual must provide user information in accordance with ±15.19(a)(3), 15.21, 15.27 and 15.105(b): Instruction Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC...
FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral deresponsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause...
Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, believes Wireless LAN is safe for use by consumers.
Regulatory Information The Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 23
For registration and license please contact IBPT/BIPT. Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462 MHz). Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig.
Page 24
Deutschland: License required for outdoor installations. Check with reseller for procedure to follow. Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen. France: Restricted frequency band: only channels 10 and 11 (2457 MHz and 2462 MHz respectively) may be used in France. License required for every installation, indoor and outdoor installations.
Nederland: License required for outdoor installations. Check with reseller for procedure to follow. Licentie verplicht voor gebruik met buitenatennes. Neem contact op met verkoper voor juiste procedure. USA-Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: •...
Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Copyright This guide is copyrighted by Corporation with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission. No patent liability is assumed, however, with respect to the use of the information contained herein.
Taiwan Article 14: Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Article 17: Any use of the low power frequency electric machinery shall not affect the aviation safety and interfere with legal communications.
Page 29
Chapter 1 Front with the Display Closed Left side Right side Bottom Front with the Display Open System Status Indicators & Controls...
Finding Your Way Around This chapter presents a grand tour of your new computer which serves as a reference when you need to locate specific parts of the computer. Front with the Display Closed The Display latch keeps the display panel closed and locked. To open the display panel, press the latch up and raise the panel.
Left side The Line In jack for an audio input device. The Microphone jack let you connect external microphone or other audio input device. The Headphone jack lets you connect stereo headphones or other audio-output devices such as external speakers. Connecting headphones or other devices to this jack automatically disables the internal speakers.
Right side The two-stacked CardBus-ready PCMCIA-compatible PC card slots allow you to install additional devices. Each slot can accommodate one Type II PC card. Both slots are able to install one Type III PC card. CAUTION: Keep foreign objects out of the PC Card slots.
Rear Side Security Lock Slot USB Ports Modem Port TV-Out Port DC-IN Socket Parallel Port Lan Port VGA Port IR Port The Fan prevents the computer’s central processing unit (CPU) and internal electronic components from overheating. CAUTION: To prevent possible overheating of the CPU, never block the fan vents.
Page 34
The Parallel port let you connect a parallel printer, or other devices including ECP-compatible devices. The Modem port lets you connect to a standard telephone line through a Modem cable The LAN port, is an RJ-45 jack for using a standard LAN cable to connect to a Local Area Network.
Bottom Side The Expansion Memory slot Cover protects the system memory modules. The Battery Release latch locks the battery in the battery bay and prevents it from falling out. To release the battery, slide the latch in the direction the arrow indicates. The Modular Bay Release latch locks a device in the modular bay.
Front with the Display Open The LCD Screen is the computer’s primary display. There are several LCD options available for this computer. The one you have will depend on which model you purchased. The options include: • 14.1” TFT with SXGA+ (1400 x 1050) resolution •...
Page 37
The Power Button turns the computer on and off, or let system enter lower power mode (Standby, Hibernation) depends on power management setting in OS. The Lid Switch can be used to control the LCD back light or let system enter a lower power suspend mode depending on the power management setting in the OS.
Page 38
System Status Indicators & Controls The System Status Indicators & Controls are divided into two sections, those on the Hinge Bar and those on the Base Panel. M P 3 The Hinge Bar indicators and controls include the following items from left to right: The Volume Control buttons adjust the audio volume level.
Page 39
3. It lights blue and blinking (LED on 1 second every 4 second) when the battery capacity is below 10%. 4. It lights blue and blinking (LED on 1 second every 2 second) when the battery capacity reaches 3%. The DC-IN LED lights blue when the computer is connected to the AC adapter and it is plugged into an AC power source.
Page 40
Computer Power Off state: Pushing the switch will turn on the ® computer, loads Windows operating system and starts the Windows Media Player which will play MP3 audio tracks you have selected. Computer Power On state: Pushing the switch starts the Windows Media Player which will play MP3 audio tracks you have selected.
Page 41
The Wireless Communication (802.11B) switch turns on and off the wireless networking transceiver. The left LED lights to indicate that wireless networking is turned on. The SmartMedia LED lights when a SmartMedia card is inserted in the SmartMedia slot and being accessed. The Caps Lock LED lights when you press the Caps Lock key.
Page 42
Chapter 2 Getting Started Setting Up Your Computer Connecting a Printer Connecting An Alternate Pointing Device Using the Computer for the First Time Registering Your Computer...
Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Making Sure You Have Everything Before doing anything else, consult the Quick Start card to make sure you received everything.
Page 44
Creating a Computer-Friendly Environment Place the computer on a flat surface, which is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation and prevent overheating.
Keeping Yourself Comfortable Strain and stress injuries are becoming more common as people spend more time using their computers. However, with a little care and proper use of the equipment, you can work comfortably throughout the day. This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive- strain injury, and repetitive-stress syndrome.
Page 46
Correct posture and positioning of the computer Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. The proper position to the K/B is at or slight below to the leavel of your below. so that your forearm will parellel to the grand. You should be able to type with relaxed shoulder.
Arms and wrists • Avoid bending, arching, or twisting your wrists. Keep them in a relaxed, neutral position while typing. • Exercise your hands, wrists, and arms to improve circulation. WARNING: Using the computer keyboard incorrectly may result in discomfort and possible wound. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest.
Page 48
Other Precautions Your computer is designed to optimize safety, minimize strain, and withstand the rigors of portability. However, you should observe certain precautions to further reduce the risk of personal injury or damage to the computer. WARNING: Avoid prolonged physical contact with the underside of the computer.
Setting Up Your Computer Setting up your computer may include: • Connecting the AC adapter • Charging the battery • Connecting a printer • Connecting an alternate pointing device Connecting the AC Adapter Your computer contains a rechargeable battery pack, which needs to be charged before you can use it the first time.
Page 50
2. Plug the AC adapter into the computer’s DC-IN socket. DC-IN Socket 3. Connect the power cable to an AC power outlet. The LED on the AC adapter comes on. If the battery is being charged, the Battery LED on the Hinge Bar of system indicator will light blue and blink.
Page 51
Charging the Battery Before you can use the battery to power the computer, you must charge it. Connect the computer to an AC power outlet using the AC adapter and power cable. The DC-IN LED will light and the Battery LED will light blue and blinking. Once the computer is connected to a power outlet, you can charge the battery with the computer turned off or on.
Connecting a Printer Before connecting a printer, you need to know whether it requires a USB or a parallel interface. Check the printer’s documentation. If the printer can be switched between USB and parallel mode choose parallel if you want to leave your USB ports free for other use.
Page 53
Connecting An Alternate Pointing Device You may want to use an external mouse or trackball instead of the computer’s built-in Touch Pad pointing device. Your computer supports USB-compatible pointing devices. The Touch Pad remains operable, even if you connect a millenary pointing device to the computer.
Using the Computer for the First Time Flip the display panel latch up to release it and then lift the display panel to open the computer. CAUTION: Don’t force the display panel open be- yond the point where it moves easily. Never lift or move the computer by grasping the display panel.
Page 55
Turning On the Computer 1. Make sure that the diskette drive is empty. 2. Open the display panel. 3. If you have a printer connected to your computer, turn the printer on and wait until it indicates it is ready. 4.
Hot keys Fn + F5 Power on display. When pressing the hot key, the display device will switch among CRT only, LCD only and simultaneous display. It will not update the setting of option ‘Power on Display’ in system setup. Fn + F10 Cursor keypad on/off.
Using the Touch Pad The Touch Pad is a touch-sensitive point device that provides all the features of a mouse. Please refer to the following instructions on how to operate the Touch Pad. The Touch Pad is easily accessible by moving either your finger off the space bar and onto the Touch Pad.
Page 58
Double clicking is a common technique for selecting objects or launching programs from icons. Move the pointer over the object you wish to select, then rapidly press the left button two times. This action is commonly referred to as “double clicking on an object.
Page 59
Chapter 3 Precautions Computing Tips Using the keyboard Starting a Program Saving Your Work Printing Your Work Backing Up Your Files Using Compact Discs Using PC Cards Using Your Computer at the Office Setting Up Communications Turning Off the Computer Caring for Your Computer...
Learning the Basics This chapter covers precautions and computing tips that you should follow when using your computer. It also provides important information about the basic features of your system. Precautions • Don’t spill liquids into the computer’s keyboard. If you did spill a liquid that gets into the keyboard, turn off the computer immediately.
To turn the numeric overlay on and off, press Fn and F11 simultaneously. The numeric mode light on the status panel glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. •...
Using the keyboard 85-key keyboard Character Keys Typing with the character keys is very much like typing on a typewriter, except that: • The spacebar creates a space character instead of just passing over an area of the page. • The lowercase letter I and the number 1 are not interchange able.
Ctrl, Fn, and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.
Overlay Keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would use the ten-key keypad on a desktop computer’s keyboard. To turn the numeric overlay on and off, press Fn and F10 first then press Fn and F11 simultaneously.
Using the Cursor Control Overlay To turn the cursor control overlay on and off, press Fn and F10 simultaneously. The cursor control light on the keyboard indicator panel glows when the cursor control overlay is on. To type alphabetic characters while the overlay is on: •...
Starting a Program from Windows Explorer If a program is not in the Programs menu, you can start it from Windows Explorer. Windows Explorer gives you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer.
NOTE: Save your data even when you are using Standby, in case the battery discharges before you return to work. Many programs offer a feature that saves documents at regular intervals, such as every 15 minutes. Check your program’s documentation to see whether they have an automatic save feature. •...
Printing Your Work ® ® Make sure that the Microsoft Windows series operating system is set up for your printer. TECHNICAL NOTE: You only need to setup the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to setup ®...
Backing Up Your Files Backing up your files simply means copying individual files to a floppy disk or copying entire sections of your hard disk to another media, such as a CD-R or CD-RW discs. Copying to a diskette 1. Insert a formatted floppy disk into the floppy disk drive. 2.
Using Compact Discs The CD-ROM drive lets you read CD-ROM discs and play audio Compact Discs. CAUTION: When inserting and removing CD-ROM discs, be careful not to touch the lens on the disc tray or the area around it, due to it may cause the drive to malfunction.
Page 71
CAUTION: If the CD is not seated properly when you close the disc tray, the CD might be damaged and the tray may not open fully when you press the eject but- ton. Removing a CD with the Computer on 1.
Caring for Compact Discs • Store your CDs in their original containers to protect them from scratches and keep them clean. • Don’t bend a CD or place heavy objects on top of it. • Don’t apply a label to, or otherwise mar, the surface of a CD. •...
Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later. Other cards may work with your computer, but are likely to be much more difficult to set up and use. Inserting PC Cards PC Cards require Card and Socket Services software a set of programs that acts as a translator between the PC Card and the...
Page 74
NOTE: If you have a Type III card, insert the connec- tor into the lower slot. If you have a Type II card, in- sert it into either the upper or the lower slot. Type II PC Card Slot Type II/III PC Card Slot NOTE: An HDD or CD-ROM connected to a 16-bit PC card, might affect the performance of the computer’s sound system and data transmission, including...
CAUTION: If your PC Card supports hot swapping, you can remove it at any time. However, to avoid data loss, never remove a card while it is in use. For more infor- mation, see “Hot swapping”. 4. Press the eject button again to eject the PC Card. The upper eject button will eject Type II PC Card from the upper slot.
• Don’t remove a SCSI card while any of the SCSI devices connected to it is operating. DEFINITION: SCSI is an acronym for Small Computer Systems Interface. A single SCSI PC Card enables you to connect several SCSI devices, such as a scan- ner or digital camera to your computer.
2. Pass the locking end through the loop. 3. Insert the cable’s locking end into the security lock slot, then rotate the key a quarter turn and remove it. Security Lock Slot Setting Up Communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: •...
Page 78
Connecting the Modem to a Telephone Line Before you can use the modem, you must connect it to a standard voice-grade telephone line. TECHNICAL NOTE: Disable Call Waiting before you connect through the modem. Call Waiting interrupts data transmission. NOTE: If you use a storage device such as a CD- ROM drive or HDD connected to a 16-bit PC card, modem speed might be slow or communication might be interrupted.
Connecting Directly to a Remote Computer If you are connecting directly to a remote computer or a bulletin board service (BBS), you need a general-purpose communications program. In addition, there are two things you need to know before you can connect to another computer: •...
File Transfer Protocols File transfer protocols are standards that given how computers transfer files between modems over a telephone line. You do not really need to know anything about specific protocols-just make sure you are using the same protocols as the computer with which you are communicating.
Caring for Your Computer This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s battery, see “Running the computer on battery power” in Chapter 5. Cleaning the Computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth.
Page 82
Chapter 4 Energy-Saving Design Managing Power Usage Charging Batteries Monitoring Battery Power Conserving Battery Power Battery Alarms Changing the Main Battery Disposing of Used Batteries Safely Traveling Tips...
Mobile Computing This chapter covers all aspects of using your computer while traveling. Energy-Saving Design Your computer enters a low-power state when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features.
Managing Power Usage Your computer’s power-saving options greatly increase the length of time you can use the computer before you need to recharge the battery. To change the power usage mode, click Start, point to Settings, then click Control Panel. In Control Panel, double-click the Power Option icon to display the Power Option Properties window.
Using Additional Battery Packs If you spend a lot of time traveling and need to work for many hours without an AC power source, you may want to carry additional charged battery packs with you. You can then replace a discharged battery and continue working.
Page 86
Charging Batteries The main battery needs to be charged before you can use it to power the computer. You can charge the battery using your computer. Charging the Main Battery To charge the batteries while they are in your computer, plug the computer into a live AC outlet.
Charging the RTC Battery In addition to the main battery, the computer contains an internal battery for the real-time clock (RTC). The RTC battery provides power for the internal real-time clock and calendar. During normal use, the main battery keeps the RTC battery adequately charged.
Page 88
Determining Remaining Battery Power NOTE: Wait at least 20 seconds after turning on the computer before checking the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform calcula- tions. ® To check the battery level, you can look at the Microsoft Windows ®...
Conserving Battery Power How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: • How is the computer configured? • How much do you use the display panel instead of an external monitor? •...
Battery Alarms The computer can be configured to warn you when the battery is running low. You can set each of the following alarms: • Low Battery • Critical Battery Each alarm can be set to alert you when a specified percentage of remaining battery power has been reached.
Changing the Main Battery When your battery runs out of power, you have two options connect the AC adapter or install a fresh battery. For instructions on using the AC adapter, see “Connecting the AC adapter”. Removing the Battery 1. Save your work. 2.
Page 92
Inserting a Battery 1. Wipe the battery terminals of the battery with a clean cloth to ensure a good connection. 2. Slide the battery in to the Battery Bay. When the battery is fully inserted, you should hear it click into place.
Disposing of Used Batteries Safely You can recharge a main battery many times. When the useful life of the battery expires or if the battery becomes damaged, you must discard it responsibly. Batteries should not be disposed of together with household waste. To make sure that they are forwarded to recycling or proper disposal they may be returned free of charge to an authorized dealer/ distributor.
Page 94
Traveling Tips The Environmental precautions also apply on journeys. • Do not leave your computer exposed to direct sunlight for long periods of time for instance, on the dashboard of a car or place it here it could get wet or covered in dust. •...
Page 95
Chapter 5 Advanced Features Using the Modular Bay Using the CD/Digital Switch to Play MP3 Tracks Audio CD Player Feature Using i.Link Port (IEEE1394) Using the SmartMedia Cards Using the IR Port Using Wireless LAN Using the Power Manager Utility...
Using Advanced Features This chapter explains many advanced features of your notebook computer. Advanced Features Your notebook built in nVidia GeForce2 Go video display hardware which supports superior 2D and 3D performance. GeForce4 420 Go Features You can either go into the GeForce4 420 Go settings through Start, Settings, Control Panel, Display or, Right-click on the Windows desktop then check Properties.
Using the Modular Bay The modular bay supports one of following removable modules: • CD-ROM drive • CD-RW drive • DVD-ROM drive • DVD/CD-RW drive • Floppy Disk drive Your computer comes with some of these drives depending on which model you purchased. You may purchase additional drives separately as accessories.
Playing DVD Your computer comes with the WinDVD software utility disc which is for playing DVD movie titles. You have to install it by yourself. Firstly, insert the disc into the drive, then the setup manual will show up automatically. You can follow the on screen display step by step method to install it.
Page 99
Using the CD/Digital Switch to Play MP3 Tracks Audio CD Player Feature This player application supports audio CDs direct play and MP3 with the computer turned off. To play MP3 files, you need to use ® the Windows Media Player that comes with the Windows operating system.
Page 100
® Using i.Link Port (IEEE1394) ® The i.Link port on the right side of the computer provides very fast data transfer rates (up to 400 Mbps or 400 Mega bits per second). You can connect up to 63 external devices to this port. In addition to its high speed, it supports isochronous data-the delivery of data at a guaranteed rate.
Page 101
Using the SmartMedia Cards The computer has a SmartMedia card slot which supports 2MB, 4MB, 8MB, 16MB, 32MB, 64MB and 128MB SmarkMedia Ramdom Access Memory (RAM) Cards. SmartMedia card are used to exchange data with other portable devices, such as digital cameras and Personal Digital Assistants (PDAs).
Page 102
Removing the SmartMedia Card CAUTION: Do not remove a SmartMedia card while data is being written or read. Data could be destroyed. Wait for the SmartMedia access LED to go out. Event if the message Copying... on the screen disappears, writing to a SmartMedia card might still be in progress.
Using the IR Port You can transfer files to another computer using your notebook computer’s Infrared port. Both computers involved in the data transfer must have compatible Infrared ports and synchronization software. Using Wireless LAN Your computer may integrate an 802.11b Wireless Networking depending on which model that you purchased.
Page 104
Using the SpeedStep Utility Your Computer supports Intel SpeedStep technology utility when your computer comes with Intel Mobile Pentium 4 CPU. The SpeedStep Technology can automatically change your computer’s performance when the power source changed. It will extend the usable length of your battery power. When your computer is running battery power, you can choose either “Battery optimized performance”...
Page 105
windows XP processor control policy The user selects the Power Scheme to be used, and Windows XP matches it with a processor control policy. Power Scheme AC Power DC Power Home/Office Desktop None Adaptive Portable/Laptop Adaptive Adaptive Minimal Power Management Adaptive Adaptive Maximize Battery Life Adaptive...
Page 106
Chapter 6 Using External Peripherals Connecting a USB Keyboard Connecting an External USB Pointing Device Connecting an External Monitor Connecting Audio Devices Connecting A Microphone Additional Disk Drive Options Upgrading System Memory...
Expanding & Upgrading This chapter covers things you can do to expand and upgrade your computer including connecting external peripherals, buying additional disk drives to use in the device bay and installing more system memory. Using External Peripherals Your computer’s numerous ports allow you to connect all sorts of peripheral devices to it.
Connecting a USB Keyboard You can install a full-size USB keyboard. This may be more convenient for some tasks and saves wear and tear on the computer’s built-in keyboard. To install an external USB keyboard do as follows: 1. Plug the keyboard into one of the USB ports on the computer. We recommend one of the rear ports if you will also connect an external pointing device for left-handed users.
Connecting an External USB Pointing Device You can install an external USB pointing device to use instead of the built-in Touch Pad device. You can use any type of pointing device as long as it has a USB interface. To install an external USB pointing device do as follows: 1.Plug the device into one of the USB ports on the computer.
Connecting an External Monitor You might want to connect an external monitor to your computer to have a larger screen and to reduce wear on the built-in LCD screen. You can connect a CRT desktop monitor to the standard 15-pin VGA port on the rear of the computer, or, if the monitor has a USB interface, to one of the USB ports.
Connecting Audio Devices The audio jacks on the left side of the computer allow you to connect several devices including speakers, a microphone and an external audio source. Connecting External Speakers You can connect self-powered stereo speakers to the computer to provide better sound reproduction than the built-in speakers and save wear on them.
Connecting A Microphone If you want to use a microphone for recording, voice commands or computer telephony, you can connect one to Microphone jack. To connect a microphone, do as follows: 1. Make sure the microphone you get is a standard computer microphone with a miniplug connector.
Connecting an External Audio Source You can connect an external audio source to the computer to transfer audio data to it for recording or to playback through the speakers. To connect an external audio source, do as follows: 1. Plug the miniplug connector from the connecting audio cable into the Line In jack on the left side of the computer.
Additional Disk Drive Options You can get additional disk drives to either install in the device bay or connect externally. Modular Bay Drive Options In addition to the drive that came in the modular bay of your computer, you can purchase any of the device bay drive options separately.
Upgrading System Memory You can upgrade the system memory in your computer. The computer has two sockets for SODIMM memory modules. They are located in the memory compartment on the underside of the computer. Generally, one socket has a module installed when you get the computer and the other socket is empty to allow for upgrades.
Page 116
The memory upgrade is now installed. Turn the computer right side up, open it and turn it on. The system should automatically recognize the new total memory capacity. You can check this by clicking on My Computer with the right Mouse button, clicking on the Properties item in the menu that appears and display the memory size in the General panel of the System Properties control panel.
Page 117
Chapter 7 Problems That are Easy to Fix Problems When you Turn On the Computer Fixing Device Related Problems Power Problems Keyboard Problems Display Problems DiskDrive Problems CD-ROM Drive Problems Sound System Problems PC Card Problems Resolving PC Card Problems Printer Problems Develop Good Computing Habit Contacying...
If Something Goes Wrong Some problems you may encounter when using the computer are relatively easy to identify and solve. Others may require helps from your dealer or the manufacturer of a software program. This chapter aims to help you solving many problems by yourself without additional helps.
Problems That are Easy to Fix Your program stops responding If you are working with a program that suddenly freezes all operations, or the execution program has stopped responding. ® You can exit the failed program without shutting down the Microsoft ®...
Page 120
Your program performs an illegal operation If you receive the message, “Your program has performed an illegal operation,” you should record the details of the message and consult the software manufacturer. To record the details: 1. Click the Details button and select the text, Microsoft ®...
You open a program that immediately stops responding If CPU Sleep mode is on (enabled), it may stop a program from responding. Close the program you are trying to open and turn off (disable) Sleep mode. Then, try to run the program again. To close the program: 1.
Power Problems The computer displays the Non-System disk or disk error message. Make sure there is no diskette in the diskette drive. If there is one, remove it and press any key to continue. If pressing any key does not work press Ctrl, Alt, and Del to restart the computer. Fixing Device-Related Problems If you do not have a hardware conflict, but you think your problem could be related to one of your computer’s devices, you can...
4. Reinstall the memory module(s), following the instructions in Chapter 7 and making sure they are seated properly in the modules sockets. 5. Check for the error again. 6. If the error recurs, remove the memory module entirely and check for the error again using the second or another module. If removing the memory module eliminates the error, the module may be faulty.
Page 124
The AC adapter and power cable work correctly, but the battery will not charge The battery doesn’t charge while the computer is consuming full power. Try turning off the computer. The main battery may not be inserted correctly in the computer. Turn off the computer, remove the battery, clean the contacts with a soft dry cloth (if necessary) and replace the battery.
Keyboard Problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself. The keyboard produces unexpected characters A keypad overlay may be on. If the numeric keypad or cursor control light is on, press Fn and F10 simultaneously to turn off the cursor control light or press Fn and F11 simultaneously to turn off the numeric keypad light.
Display Problems Here are some typical display problems and their solutions: The display is blank Display Auto Off may have gone into effect. Press any key to activate the screen. If you are using the built-in screen, make sure the display priority is not set for an external monitor.
Page 127
Properties dialog box. The Appearance tab of this dialog box allows you to choose the colors for the screen. The Settings tab allows you to choose the screen resolution. The built-in screen flickers Some flickering is a normal result of the way the screen produces colors.
Disk Drive Problems Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them. Typical disk problems are: You are having trouble accessing a disk, or one or more files appear to be missing Make sure you are identifying the drive by its correct name...
Page 129
Your data files are damaged or corrupted Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software, which is available from your dealer. Some programs run correctly but others do not This may be a software configuration problem.
The drive can not read a diskette Try another diskette. If you can access the second diskette, the first diskette (not the diskette drive) is probably causing the problem. Run ScanDisk on the faulty diskette (for instructions, see “Disk drive problems”). CD-ROM Drive Problems You cannot access a CD in the drive Make sure the CD-ROM tray has closed properly.
Some CDs run correctly, but others do not If the problem is with a data CD, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The color of the materials used to make the CD can affect its reliability.
PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, fax/modem, or pager. Most PC Card problems occur during installation and setup of new cards. If you’re having trouble getting one or more of these devices to work together, several sections in this chapter may apply.
Resolving PC Card Problems Here are some common problems and their solutions: The slots appear to be dead and PC Cards that used to work no longer do Check the PC Card status: 1. Click the My Computer icon with the secondary button, then click Properties.
Page 134
Hot swapping (removing one PC Card and inserting another without turning the computer off) fails Follow this procedure before you remove a PC Card: 1. Click the PC Card icon on the taskbar. 2. Click Stop xxxx, where xxxx is the identifier for your PC Card.
A PC Card error occurs Reinsert the card to make sure it is properly connected. If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshooting section. Printer Problems This section lists some of the most common printer problems.
The printer will not print what you see on the screen Many programs display information on the screen differently from the way they print it. See if your program has a print preview mode. This mode lets you see your work exactly as it will print. Contact the software manufacturer for more information.
Page 137
Develop Good Computing Habit • Make sure you are prepared. • Save your work frequently. You can never predict when your computer will lock forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Get familiar with all the user’s guides provided with your computer, as well as the manuals that come with the programs and devices you purchased. Your local computer store or book store sells a variety of self-help books you can use to supplement the information in the manuals. •...
Page 139
• If the problem occurs while you are running a program, consult the program’s documentation for troubleshooting suggestions. Contact the software company’s technical support group for their assistance. • Consult the dealer from whom you purchased your computer and/or program. Your dealer is your best source for current information.
Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a label on or above the key indicating the option or feature the key controls. Power-on Display Power on display.
Features and Specifications This appendix lists the features of the computers and summarizes their specifications. Features This section lists the computer’s standard features and specifications. • Intel Pentium 4 1.4GHz/1.5GHz/1.6GHz/1.7GHzHz • µFCPGA Socket CPU, 512KB L2 Cache on CPU • Designed for Intel SpeedStep •...
Page 144
• LPC47N227 Super I/O controller. • OZ165 for Direct CD play controller. • VT6306 for 1394 controller. • RTL81 for LAN controller. • TC6371AF for SmartMedia controller. Memory • No onboard memory. • Supports 200/266M DDR RAM modul 128MB, 256MB,512MB •...
Power • 8 cells LI-ION 18650 size battery Pack with 58.05WH capacity. • Approximately 2.5 hours operation with default setting (Running Battery mark 4.0.1). • Approximately 3.0 hours charging time to 100% capacity on single 3900mAH Li-Ion Battery (System off or Suspend). One 2.5", 9.5mm Hard Disk, Up to 30GB •...
Page 146
Touch Pad pointing device with two buttons • Left Button • Right Button I/O Ports • One 25 pins Parallel port, EPP/ECP Capability • One 15 pins CRT port, Support DDC 2B • One 7 pins TV out port • One MIC-In port •...
PCMCIA Card • One type III card socket or two type II card sockets • SRAM, OTPROM, FLASH ROM, mask ROM memory card up to 64MB • MODEM/LAN card • 1.8" 10.5mm removable ATA Device • Card bus card • ACPI 1.0 Compliant Power Management Function •...
Page 148
Switches • Power switch • Lid switch • Wireless • CD/Digital Switch • Stop Button • Play/ Pause Button • Reverse Button • Forward Button • Volume Down Button • Volume Up Button • Internet Button • Application Button AC Adapter •...
Power Cable Connectors The computer features a universal power supply you can use worldwide. This appendix shows the configuration of typical AC power cord plugs and sockets in various parts of the world. USA and Canada UL approved CSA approved United Kingdom BS approved Australia...
Need help?
Do you have a question about the SilverSeraph CL10 and is the answer not in the manual?
Questions and answers