Related Manuals for INTERNATIONAL CARBONIC TUACA
Summary of Contents for INTERNATIONAL CARBONIC TUACA
- Page 1 TUACA PUSH HERE Installation and Service Manual INTERNATIONAL CARBONIC INC. 16630 Koala Rd. Adelanto, California 92301 800 854-1177 3/22/05...
- Page 2 IMPORTANT: This manual guide installing, operating, servicing and maintaining this equipment. Refer Table Contents page location detailed information answer questions that arise during installation, operating, service maintenance, installation of this equipment.
-
Page 3: Table Of Contents
CHAPTER II UNPACKING AND INSPECTION............8 SELECTING LOCATION..............8 LOCATION RECOMMENDATIONS ............ 8 ELECTRICAL REQUIREMENTS............8 TUACA UNIT INSTALLATION INSTRUCTIONS......... 9 FLOW PLAN BOTTLE MOUNT............11 CHAPTER III OPERATORS INSTRUCTIONS ............12 DAILY PRE-OPERATION CHECK ............12 COOLING UNIT MAINTENANCE............12 CLEANING NOZZLE ................ -
Page 4: Preface
PREFACE INTERNATIONAL CARBONIC INC. has enjoyed over 53 years of manufacturing excellence in the field of carbonation and in the beverage related industry. We have been located in the Southern California area since 1952 and have a long and proud history with quality as our standard and innovation as our goal. -
Page 5: General Description
Essentially the TUACA unit is designed to plug and play. For proper function the TUACA unit must have 120 volt electrical supply and proper space around unit to allow the refrigeration to breath during operation. The TUACA unit is designed with a unique lift off drain pan that can be emptied at any convenient drain outlet. -
Page 6: Theory Of Operation
As the incoming TUACA passes through the cooling coil the heat is removed from the TUACA and chilled to a temperature acceptable for a quality drink, normally a temperature 7 to 16 degrees is reached. The TUACA is now directed to a dispensing nozzle where... -
Page 7: Exploded View
TUACA TITLE CHILL SHOT INTERNATIONAL CARBONIC INC. I C I TUACA DATE 7/20/05 DRN. BY CHK. BY APPR. BY ADELANTO, CALIFORNIA... -
Page 8: Exploded View Description
S0956-9 LAMP, 9" E0665 STRAIN RELIEF S0955 STARTER S0973 LAMP HOLDER S1832 LOGO FRONT, I.D., TUACA S1832-F FRAME, LOGO FRONT, I.D., TUACA S1827 SERVICE PANEL, REAR S1828 SERVICE PANEL, LEFT S1829 SERVICE PANEL, RIGHT S1830 FRONT PLATE S1833 FRAME S1834... - Page 9 TUACA Cont. SYM QTY PART NO. DESCRIPTION A0014 SCREW, #10 X 1/2 PH TH COMBO SS - - - - - INSULATION, EVAP, 3" IPS X 3/4 WALL, 12" S0509 ACCUMULATOR E0664 STRAIN RELIEF S1722 TUBING, NOR-6F-250, 8" S1737-CS PERISTALTIC PUMP MODULE, CS...
-
Page 10: Electric Schematic
BLACK WHITE... -
Page 11: Unpacking And Inspection
This chapter covers unpacking and inspection, selecting location, installing TUACA unit and electrical requirements. UNPACKING AND INSPECTION Upon receiving unit, immediately remove TUACA unit from shipping carton and inspect for shipping damage. NOTE: Remove the TUACA unit from the shipping carton and inspect for shipping damage. If shipping damage is found immediately contact Sentry BevCon at (800) 661-3003. -
Page 12: Tuaca Unit Installation Instructions
TUACA Installation Instructions Remove the TUACA unit from the shipping carton and inspect for shipping damage. If shipping damage is found immediately contact Sentry BevCon at 800 661-3003. Do not discard the shipping carton or any shipping materials in the event a freight claim must be filed. - Page 13 #12. 9. Activate the "PUSH HERE" switch until the TUACA is dispensed. The level of the TUACA in the bottles will drop as the cooling coils are filled. Dispense 6-8 ounces in order to flush unit. DO NOT REUSE! 10.
-
Page 14: Flow Plan Bottle Mount
9. Plug unit into 110-volt outlet to engage the condensing unit and lights. Immediately activate PUSH "Cold Shot" switch until a small amount of Tuaca is dispensed. 10. Tuaca will be ready to dispense in approximately 15 minutes. SUPPORT ASSEMBLY 10/03 Revised 9/5/04... -
Page 15: Operators Instructions
This chapter covers operators’ responsibilities for daily pre-operation check, adjustments, cleaning, and sanitizing. DAILY PRE-OPERATION CHECK Make sure TUACA reservoir is full and ready to dispense. Make sure nozzle is clean. Make sure electrical power is supplied to unit. Make sure unit is clean. -
Page 16: Cleaning Condenser Coil
CLEANING CONDENSER COIL IMPORTANT: Air circulation through the condenser coil required to cool the condenser coil/compressor, is drawn in through grills on cooling unit, through condenser coil and exhausted out grills on the other side of unit. Restricting air circulation through the cooling unit will decrease its cooling capacity. - Page 17 1. Turn off TUACA by unplugging unit. Remove front panel and then remove control access panel. Disconnect wires at A6 and B6 on control terminal board. Plug TUACA into 110 volt outlet, activate push switch and empty out product from tubing by flushing with warm water.
-
Page 18: Frequently Asked Question
FREQUENTLY ASKED QUESTION: Q. Should the machine be left on all the time? A. Yes, your electrical usage will be minimal and the TUACA unit will have less electrical and refrigeration problems. Q. If the machine is left on how much will the electricity bill go up? A. -
Page 19: Trouble Shooting
IMPORTANT: Only qualified personnel should service TUACA unit and components. WARNING: To avoid personal injury and or property damage, always disconnect electrical power, before starting any repairs. If repairs are to be made to the TUACA unit, drain TUACA unit before proceeding. COOLING UNIT... -
Page 20: Notes
Attach disconnected wire. Defective PPM assy. Replace PPM assy. Worn or defective neoprene Replace defective tubing. tubing in PPM assy. No TUACA TUACA reservoir empty. Replenish TUACA supply. being PPM Assy defective. Replace PPM Assy. dispensed Defective neoprene tubing. Replace neoprene tubing.