Stopping The Lap Timer; Viewing Lap Times; Setting The Interval Timer - AIRTRONICS M12 User Manual

M12 2.4GHZ FH4T RADIO CONTROL SYSTEM USER'S GUIDE
LAp TIMER MENU { vIEw LAp TIMES AND CHOOSE LAp TIMER OpTIONS }

Stopping the Lap Timer:

1) To Stop the Lap Timer, press and HOLD the Lap Timer Switch for 3 seconds. An audible Double-Tone will sound and LAP
[STOPPED] will be displayed momentarily in a pop-up window, indicating the Lap Timer is stopped.
The Cumulative Time cannot be manually cleared. It will be automatically cleared when the Lap Timer is put in Standby again.

Viewing Lap Times:

The Cumulative Lap Time, the Best Lap Time and the Average Lap Time, in addition to up to 250 individual Lap Times can be
viewed on the TELEMETRY screen LAP page.
1) From the STATUS screen, scroll UP or DOWN to open the TELEMETRY screen. Press the SELECT switch Right or Left to open
the LAP page.
2) Press the ENTER key, then scroll UP or DOWN to view the individual Lap Times.
Lap Times are stored until you Restart the Lap Timer. When the Lap Timer is Restarted, old Lap Times are Cleared and
new Lap Times are Stored.
INT1 AND INT2 MENU { INTERvAL 1 AND INTERvAL 2 TIMERS }
The Interval Timer function is used to notify you when a set Interval elapses while you're driving. When the Interval Time is
reached, an audible Double-Tone will sound, then the Interval Timer will Reset and begin counting Up again from zero. Interval
Times are displayed in the following format: 00':00".00 (Minutes : Seconds : 1/100th of a Second). The Interval Timer can be
programmed to work independently or programmed to work along with the Lap Timer function.
This section covers both the INT1 and INT2 menus, since programming each of them is exactly the same. Choose either the
INT1 or the INT2 menu depending on which of the two Interval Timers you want to program.

Setting the Interval Timer:

1) From within the SETUP menu, scroll UP or DOWN to highlight either the INT1
or the INT2 menu depending on which Interval Timer you want to program. In
this section, we show programming Interval Timer 1.
2) Press the ENTER key to open the INT1 menu. INTERVAL > 00' will be highlighted.
3) Scroll UP or DOWN to highlight the desired Interval Timer value you would like
to change, either 00' (Minutes) , 00" (Seconds) or 00 (1/100th Seconds).
4) Press the ENTER key, then scroll UP or DOWN to choose the desired Interval
Timer value.
5) Press the ENTER key again, then repeat steps 3 and 4 to change any other
desired Interval Timer values.
INT1 and INT2 INTERVAL setting range is 00:00:00 to 99:59:90. The default setting for both Interval Timers is 00:00:00 (OFF).
Choosing the Optional Throttle Trigger Start:
The Throttle Trigger can be used to Start the Interval Timer after the Interval Timer as been placed in Standby. This is much more
convenient than worrying about pressing the Interval Timer Switch again to Start the Interval Timer when you're starting your race.
There are two Interval Timers. These Interval Timers can be Started and
Stopped independently by Assigning each one to a different Push-Button
Switch or they can be Started and Stopped simultaneously by Assigning
both of them to the same Push-Button Switch. If desired, different Tones can
be Assigned to each Interval Timer to differentiate them and the Throttle
Trigger can be programmed to Start the Interval Timer(s).
In the default configuration, Interval Timer 1 is Started and Stopped along
with the Lap Timer, using the Lap Timer Switch (Push-Button Switch Sw3).
T
SETUp
SETUp
73