Table of Contents
Advertisement
Owner's Manual Models 750 & 770
HONESTLY NOW ... Have you read this OWNER'S MANUAL?
• Safety
• Assembly
• Operation
• Accessory Information
• Warranty
• Registration Form
• Service Parts
2 610 917 153 9/02
1-800-437-3635
http://www.dremel.com
P.O. Box 1468
Racine, Wisconsin 53401
P
arlez-vous français?
Voir page 21
¿Habla español?
Vea página 41
PRINTED IN U.S.A.
Advertisement
Table of Contents
Related Manuals for Dremel 750
Summary of Contents for Dremel 750
- Page 1 Cordless Rotary Tool Owner’s Manual Models 750 & 770 HONESTLY NOW … Have you read this OWNER’S MANUAL? • Safety arlez-vous français? Voir page 21 • Assembly ¿Habla español? • Operation Vea página 41 • Accessory Information • Warranty • Registration Form •...
- Page 2 General Safety Rules for All Battery Operated Tools Read and understand all instructions. Failure to follow all instructions listed below, may result WARNING in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area locked or off position before inserting battery pack. Carrying tools with your finger on the switch or insert- Keep your work area clean and well lit.
- Page 3 Shorting the battery terminals together may cause manufacturer for your model. Accessories that may be sparks, burns, or a fire. suitable for one tool may create a risk of injury when used on another tool. Maintain tools with care. Keep cutting tools sharp and Service clean.
- Page 4 Dull bits require more force to push the tool, possibly Regularly clean the tool's air vents by compressed causing the bit to break. air. Excessive accumulation of powdered metal inside the motor housing may cause electrical failures. Use clamps to support workpiece whenever practical. Never hold a small workpiece in one hand and the Do not allow familiarity gained from frequent use of tool in the other hand while in use.
- Page 5 Use of an attachment not recommended or sold by Nickel-Metal Hydride Batteries Dremel may result in a risk of fire, electric shock or If equipped with a nickel-metal hydride battery, the bat- injury to persons.
- Page 6 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation Volts Voltage (potential) Amperes Current Hertz...
- Page 7 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. This symbol designates that this This symbol designates tool is listed to Canadian that this tool is listed by...
- Page 8 Functional Description & Specifications Disconnect battery pack from tool or place the switch in the locked or off position before WARNING making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Cordless Rotary Tool BATTERY COLLET NUT...
- Page 9 COLLETS — Four different size collets (see illus- tration), to accommodate different shank sizes, are Remember, your new Dremel Cordless Rotary Tool is available for your Cordless Rotary Tool. To install a dif- the finest power tool of its kind. But its performance...
-
Page 10: Operation Instructions
Operation Instructions Introduction runs at speeds up to 2,800 revolutions per minute. The typical electric drill is a low-speed, high torque tool; the The Cordless Rotary Tool is a handful of high-speed Cordless Rotary Tool is just the opposite — a high- power. - Page 11 Using the Cordless Rotary Tool Usually, it is best to make a series of passes with the tool rather than attempt to do all the work in one pass. The first step in learning to use the Cordless Rotary Tool To make a cut, for example, pass the tool back and forth is to get the “feel”...
- Page 12 On the Model 750, there is a LO and HI switch. When the switch indicator is in position 1 or LO, the tool runs at about 6,500 RPM. When the switch indicator is in position 2 or HI, the tool runs at about 13,000 RPM.
- Page 15 We recommend that all Extension Cords tool service be performed by a Dremel Service Facility. If an extension cord is necessary, SERVICEMEN: Disconnect tool and/or charger from CAUTION a cord with adequate size conduc- power source before servicing.
- Page 16 Cordless Rotary Tool Accessories Use only Dremel Tested, High Performance Accessories. Other accessories are not WARNING designed for this tool and may lead to personal injury or property damage. The number and variety of accessories for the Rotary Tool are almost limitless. There is a category suited to Threaded Tip Mandrel No.
- Page 17 No polishing compound is needed when using the 425 Polishing Wheel or 427 Polishing point. Aluminum Oxide Grinding Stones (orange/brown) Round, pointed, flat — you name the shape and there is one available in this category. These are made of alu- minum oxide and cover virtually every possible kind of grinding application.
- Page 18 Cordless Rotary Tool Accessories (Cont.) Use only Dremel Tested, High Performance Accessories. Other accessories are not WARNING designed for this tool and may lead to personal injury or property damage. Bristle Brushes These are excellent cleaning tools on silverware, jew- Grinding Wheel elry and antiques.
- Page 19 Mandrel No. 401 is used with the felt polishing tip and The felt tip must thread down straight on the screw wheels. Thread the tip on to the screw carefully. Mandrel, and be turned all the way to the collar. Mandrel No.
- Page 20 Dremel Limited Warranty Your Dremel product is warranted against defective material or workmanship for a period of two years from date of purchase. In the event of a failure of a product to conform to this written warranty, please take the following action: 1.
- Page 21 MODEL 750 Type 2 MODÈLE 750 Type 2 MODELO 750 Tipo 2 CODE PART DESCRIPTION DESCRIPTION DESCRIPCION 2615297355 Collet Nut Ecrou De Douille Tuerca del portaherramienta 2615000480 1/8" Collet (In Tool) Douille 3,2 mm po (avec l'outil) Portaherramienta de 3,2 mm...
- Page 22 MODEL 770 Type 2 MODÈLE 770 Type 2 MODELO 770 Tipo 2 CODE PART DESCRIPTION DESCRIPTION DESCRIPCION 2615297355 Collet Nut Ecrou De Douille Tuerca del portaherramienta 2615000480 1/8" Collet (In Tool) Douille 3,2 mm po (avec l'outil) Portaherramienta de 3,2 mm 2610917263 Shaft Lock Assembly Ensemble de blocage de l’arbre...
- Page 23 Página 63...