Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ShoreTel Mobility Router 6000 Series
Summary of Contents for ShoreTel Mobility Router 6000 Series
- Page 1 ShoreTel Mobility Router 6000 Series Hardware Installation Guide...
-
Page 2: Version Information
ShoreGear, ShorePhone, and ShoreWare are registered trademarks of ShoreTel, Inc. in the United States and/or other countries. The ShoreTel logo is a trademark of ShoreTel, Inc. in the United States and/or other countries.. All other copyrights and trademarks herein are the property of their respective owners. -
Page 3: Table Of Contents
“Connecting to the Console Port” on page 9 “Connecting Power” on page 10 “Installing the Front Panel Cover (Optional)” on page 11 “Using the Initial Configuration Wizard” on page 12 ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 4: Specifications
Specifications The Mobility Router is one rack unit (RU) high and installed in a standard 19-inch (48.26-cm) rack. Figure 1-1. Front View of RoamAnywhere Mobility Router 6000 Series Figure 1-2. Rear View of RoamAnywhere Mobility Router 6000 Series NOTE The Mobility Router ships with the front panel cover uninstalled. Refer to “Installing the Front Panel Cover (Optional)”... -
Page 5: Unpacking A Mobility Router
A copy of this document Before starting the installation: Open the carton and remove the contents. If any contents are missing or damaged, contact ShoreTel Technical Support at +1.408.331.3300 or http://support.shoretel.com. Keep the packing materials and save the carton. -
Page 6: Installation Requirements And Recommendations
Mounting screws to rack mount the Mobility Router (not provided) Screwdriver (not provided) 1.4.4 Uninterruptible Power Supply We recommend installing the Mobility Router in an existing Uninterruptible Power Supply (UPS) infrastructure. ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 7: Installing The Mobility Router
Attach the rear inner rails to the chassis. The rear inner rails are labeled with “Back” and an arrow, indicating which way the rail should be facing. Figure 1-4 shows how to install rear inner rails. ShoreTel Mobility Router 6000 Series Hardware Installation Guide... - Page 8 End of the rail labeled “Back” is at the back of the rack. Attach the rack rail to the rack by inserting screws in the brackets at the ends of the rack rail. ShoreTel Mobility Router 6000 Series Hardware Installation Guide...
- Page 9 Mobility Router has been completely inserted into the rack. Insert screws in the mounting brackets on the front of the Mobility Router to the rack. Figure 1-5. Installing the Mobility Router into the Rack ShoreTel Mobility Router 6000 Series Hardware Installation Guide...
-
Page 10: Connecting To The Network
Insert the other end of the Ethernet cable to the left Ethernet port (ETH0) on the rear of the Mobility Router. NOTE If using the Secure Remote Voice feature, connect the second Ethernet port (ETH1) to the external network. Figure 1-6. Connecting the Ethernet Cable to the Mobility Router ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 11: Connecting To The Console Port
HyperTerminal) and select the appropriate COM port. Configure the port using the following settings: Baud rate: 9600 bps Data bits: 8 Parity: None Stop bits: 1 Flow control: None ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 12: Connecting Power
As the Mobility Router starts up, messages display in the terminal emulation software window. Use the initial configuration wizard to initially configure the Mobility Router with “Using the Initial Configuration Wizard” on page ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 13: Installing The Front Panel Cover (Optional)
Press the front panel against the Mobility Router until the peg covers on the right side of the front panel slide into the screw holes of the right mounting bracket ear. Figure 1-11. Insert Right Side of Front Panel ShoreTel Mobility Router 6000 Series Hardware Installation Guide... -
Page 14: 1.10 Using The Initial Configuration Wizard
Enter the subnet mask in the format of a 32-bit mask or classless interdomain routing (CIDR) notation. Enter the IP address of the default gateway for the Mobility Router. Enter the IP address of the primary DNS server. ShoreTel Mobility Router 6000 Series Hardware Installation Guide... - Page 15 After verifying access to the Administration Portal, disconnect the serial cable. (Console access is no longer required.) The ShoreTel Mobility Router is now ready to be configured using the Administration Portal. For more information, see the RoamAnywhere Mobility Router Administrator’ s Guide.
- Page 16 ShoreTel Mobility Router 6000 Installation Using the Initial Configuration Wizard ShoreTel Mobility Router 6000 Series Hardware Installation Guide...