Siemens MICROMASTER 430 Operating Instructions Manual page 69

Issue 05/02
ParNo
P1323[3]
P1324[3]
P1325[3]
P1330[3]
P1333[3]
r1337
P1335[3]
P1336[3]
P1338[3]
P1340[3]
r1343
P1341[3]
r1344
P1345[3]
P1346[3]
P1350[3]
Communication (P0004 = 20)
ParNo
P0918
P0927
r0965
r0967
r0968
r0964[5]
P0971
P2000[3]
P2001[3]
P2002[3]
P2003[3]
r2004[3]
P2009[2]
P2010[2]
P2011[2]
P2012[2]
P2013[2]
P2014[2]
r2015[8]
P2016[8]
r2018[8]
r2024[2]
P2019[8]
r2025[2]
r2026[2]
r2027[2]
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
ParText
Programmable V/f volt. coord. 2
Programmable V/f freq. coord. 3
Programmable V/f volt. coord. 3
CI: Voltage setpoint
Start frequency for FCC
CO: V/f slip frequency
Slip compensation
Slip limit
Resonance damping gain V/f
Imax controller prop. gain
CO: Imax controller freq. output
Imax controller integral time
CO: Imax controller volt. output
Imax controller prop. gain
Imax controller integral time
Voltage soft start
ParText
CB address
Parameter changeable via
Profibus profile
Control word 1
Status word 1
Firmware version data
Transfer data from RAM to EEPROM
Reference frequency
Reference voltage
Reference current
Reference torque
Reference power
USS normalization
USS baudrate
USS address
USS PZD length
USS PKW length
USS telegram off time
CO: PZD from BOP link (USS)
CI: PZD to BOP link (USS)
CO: PZD from COM link (USS)
USS error-free telegrams
CI: PZD to COM link (USS)
USS rejected telegrams
USS character frame error
USS overrun error
5 System parameters
Default Level DS
0.0 3 CUT
0.00 3 CT
0.0 3 CUT
0:0 3 T
10.0 3 CUT
- 3 -
0.0 3 CUT
250 3 CUT
0.00 3 CUT
0.000 3 CUT
- 3 -
0.300 3 CUT
- 3 -
0.250 3 CUT
0.300 3 CUT
0 3 CUT
Default Level DS
3 2 CT
15 3 CUT
- 3 -
- 3 -
- 3 -
- 3 -
0 3 CUT
50.00 2 CT
1000 3 CT
0.10 3 CT
0.75 3 CT
- 3 -
0 3 CT
6 3 CUT
0 3 CUT
2 3 CUT
127 3 CUT
0 3 CT
- 3 -
52:0 3 CT
- 3 -
- 3 -
52:0 3 CT
- 3 -
- 3 -
- 3 -
QC
N
N
N
N
N
-
N
N
N
N
-
N
-
N
N
N
QC
N
N
-
-
-
-
N
N
N
N
N
-
N
N
N
N
N
N
-
N
-
-
N
-
-
-
69