Siemens MICROMASTER 430 Operating Instructions Manual page 67

Issue 05/02
ParNo
P1027
P1032
P1031[3]
P1040[3]
r1050
P1070[3]
P1071[3]
P1075[3]
r1078
P1076[3]
P1080[3]
P1082[3]
P1091[3]
P1092[3]
P1093[3]
P1094[3]
P1101[3]
r1114
r1119
P1120[3]
P1121[3]
P1130[3]
P1131[3]
P1132[3]
P1133[3]
P1134[3]
P1135[3]
r1170
Drive Features (P0004 = 12)
ParNo
P0005[3]
P0006
P0007
P0011
P0012
P0013[20]
P1200
P1202[3]
P1203[3]
P1210
P1211
P1212
P1213
P1215
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
ParText
Fixed frequency mode - Bit 5
Inhibit reverse direction of MOP
Setpoint memory of the MOP
Setpoint of the MOP
CO: Act. Output freq. of the MOP
CI: Main setpoint
CI: Main setpoint scaling
CI: Additional setpoint
CO: Total frequency setpoint
CI: Additional setpoint scaling
Min. frequency
Max. frequency
Skip frequency 1
Skip frequency 2
Skip frequency 3
Skip frequency 4
Skip frequency bandwidth
CO: Freq. setp. after dir. ctrl.
CO: Freq. setpoint before RFG
Ramp-up time
Ramp-down time
Ramp-up initial rounding time
Ramp-up final rounding time
Ramp-down initial rounding time
Ramp-down final rounding time
Rounding type
OFF3 ramp-down time
CO: Frequency setpoint after RFG
ParText
Display selection
Display mode
Backlight delay time
Lock for user defined parameter
Key for user defined parameter
User defined parameter
Flying start
Motor-current: Flying start
Search rate: Flying start
Automatic restart
Number of restart attempts
Time to first restart
Restart time increment
Holding brake enable
5 System parameters
Default Level DS
1 3 CT
1 3 CT
0 3 CUT
5.00 2 CUT
- 3 -
755:0 3 CT
1:0 3 CT
0:0 3 CT
- 3 -
1:0 3 CT
0.00 1 CUT
50.00 1 CT
0.00 3 CUT
0.00 3 CUT
0.00 3 CUT
0.00 3 CUT
2.00 3 CUT
- 3 -
- 3 -
10.00 1 CUT
30.00 1 CUT
0.00 2 CUT
0.00 2 CUT
0.00 2 CUT
0.00 2 CUT
0 2 CUT
5.00 2 CUT
- 3 -
Default Level DS
21 2 CUT
2 3 CUT
0 3 CUT
0 3 CUT
0 3 CUT
0 3 CUT
0 3 CUT
100 3 CUT
100 3 CUT
1 3 CUT
3 3 CUT
30 3 CUT
30 3 CUT
0 2 T
QC
N
N
N
N
-
N
N
N
-
N
Q
Q
N
N
N
N
N
-
-
Q
Q
N
N
N
N
N
Q
-
QC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
67