Siemens MICROMASTER 430 Operating Instructions Manual page 68

5 System parameters
ParNo
P1216
P1217
P1232[3]
P1233[3]
P1234[3]
P1236[3]
r1242
P1240[3]
P1243[3]
P1254
P1253[3]
r1261
P1260[3]
P1262[3]
P1263[3]
P1264[3]
P1265[3]
P1266[3]
Motor Control (P0004 = 13)
ParNo
r0020
r0021
r0022
r0024
r0025
r0027
r0032
r0038
r0056
r0061
r0065
r0067
r0071
r0086
P0095[10]
r0096[10]
P1300[3]
P1310[3]
P1311[3]
P1312[3]
P1316[3]
P1320[3]
P1321[3]
P1322[3]
68
ParText
Holding brake release delay
Holding time after ramp down
DC braking current
Duration of DC braking
DC braking start frequency
Compound braking current
CO: Switch-on level of Vdc-max
Configuration of Vdc controller
Dynamic factor of Vdc-max
Auto detect Vdc switch-on levels
Vdc-controller output limitation
BO: Contactor control word
source of changeover control
Bypass dead time
De-Bypass time
Bypass time
Bypass frequency
BI: Bypass command
ParText
CO: Act. frequency setpoint
CO: Act. frequency
Act. rotor speed
CO: Act. output frequency
CO: Act. output voltage
CO: Act. output current
CO: Act. power
CO: Act. power factor
CO/BO: Status of motor control
CO: Act. rotor speed
CO: Slip frequency
CO: Act. output current limit
CO: Max. output voltage
CO: Act. active current
CI: Display PZD signals
PZD signals
Control mode
Continuous boost
Acceleration boost
Starting boost
Boost end frequency
Programmable V/f freq. coord. 1
Programmable V/f volt. coord. 1
Programmable V/f freq. coord. 2
Default Level DS
1.0 2 T
1.0 2 T
100 3 CUT
0 3 CUT
650.00 3 CUT
0 3 CUT
- 3 -
1 3 CT
100 3 CUT
1 3 CT
10 3 CUT
- 2 -
0 2 CT
1.000 2 CUT
1.0 2 CUT
1.0 2 CUT
50.00 2 CT
0:0 2 CT
Default Level DS
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
- 3 -
0:0 3 CT
- 3 -
1 3 CT
50.0 3 CUT
0.0 3 CUT
0.0 3 CUT
20.0 3 CUT
0.00 3 CT
0.0 3 CUT
0.00 3 CT
MICROMASTER 430 Operating Instructions
6SE6400-5AE00-0BP0
Issue 05/02
QC
N
N
N
N
N
N
-
N
N
N
N
-
N
N
N
N
N
N
QC
-
-
-
-
-
-
-
-
-
-
-
-
-
-
N
-
Q
N
N
N
N
N
N
N