Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Pro-Line Boats Manuals
  4. Motorized Toy Car
  5. Pro-mt
  6. Assembling instructions

Pro-Line Boats Pro-mt Assembling Instructions

1:10 2wd monster truck kit
Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading

Related Manuals for Pro-Line Boats Pro-mt

Summary of Contents for Pro-Line Boats Pro-mt

  • Page 2: Tools Required

    Thank you for purchasing Pro-Line’s PRO-MT! For over the best performance parts and combined them into 30 years, Pro-Line has designed and manufactured the one complete kit. Congratulations on making the right best RC accessories in the world. Pro-Line has taken...
  • Page 3 HARDWARE USED Front Bumper Assembly (ACTUAL SIZE) M3 × 12 × 2 M3 × 8 SHCS × 2 M3 × 12 SHCS M3 × 8 HARDWARE USED Front Shock Tower to Bulkhead (ACTUAL SIZE) × 2 M3 × 16 BHCS HARDWARE USED Front Bumper to Bulkhead (ACTUAL SIZE)
  • Page 4 HARDWARE USED Front Shock Mounting Hardware (ACTUAL SIZE) × 2 M3 X 30 SHCS × 2 OUTSIDE HOLES M3 Washer × 2 Ball Ends × 2 M3 Locknut HARDWARE USED Front Body Mount to Shock Tower (ACTUAL SIZE) HOLE fROM TOP ×...
  • Page 5 HARDWARE USED Front Camber Link Rod Ends (ACTUAL SIZE) 50mm (ACTUAL SIZE) × 4 Long Rod Ends 27.5mm (ACTUAL SIZE) × 2 USE INCLUDED TURNBUCKLE WRENCH HARDWARE USED Front Camber Link Pivot Balls (ACTUAL SIZE) DRIVER’S SIDE LINK × 2 Small Inner Pivot Balls ×...
  • Page 6 HARDWARE USED Front Arms & Hinge Pin Brace to Bulkhead (ACTUAL SIZE) × 2 Front Inner Hinge Pin × 2 M3 Locknut Hinge Pin Brace × 1 HARDWARE USED Front Hub Assembly (ACTUAL SIZE) × 4 5 × 11 Bearing ×...
  • Page 7 HARDWARE USED Front Hub Assembly to Camber Link & Arm (ACTUAL SIZE) × 2 M3 LOCKNUT Front Outer Hinge Pin × 2 OUTSIDE HOLE M2.5 Locknut × 2 M2.5 LOCKNUT M3 × 18 BHCS × 2 M3 Locknut REPEAT THIS STEP fOR OPPOSITE SIDE HARDWARE USED Steering Links to Rod Ends &...
  • Page 8 HARDWARE USED Steering Links to Steering Kit (ACTUAL SIZE) × 2 M3 Locknut HARDWARE USED Assemble Front End to Chassis (ACTUAL SIZE) × 3 M4 × 10 FHCS HARDWARE USED Front Bumper Brace to Front Bulkhead (ACTUAL SIZE) × 2 M4 ×...
  • Page 9 HARDWARE USED Rear Shock Mounting Hardware (ACTUAL SIZE) × 2 M3 × 25 SHCS × 2 INNER HOLES M3 Washer × 2 Ball Ends × 2 M3 Locknut *Use caution if using power tools. Heat may melt plastic. HARDWARE USED Rear Camber Links to Rod Ends &...
  • Page 10 HARDWARE USED Rear Shock Tower to Transmission Case (ACTUAL SIZE) × 4 M3 × 16 BHCS HARDWARE USED Rear Body Mount to Shock Tower (ACTUAL SIZE) TOP HOLES × 2 M3 × 14 BHCS × 4 M2.5 × 12 SHCS HARDWARE USED Rear Body Mount Hardware (ACTUAL SIZE)
  • Page 11 HARDWARE USED Outdrive Assembly (ACTUAL SIZE) × 2 PRO TIP Rotate retainer clip so slit is away drive Pin from pin holes and add a drop of CA Tire Glue (not included) in slit to × 2 prevent rotation of clip. drive Pin Cup ×...
  • Page 12 HARDWARE USED Driveshaft to Outdrive & Hub Carrier (ACTUAL SIZE) × 2 18 × 12 × 4 Bearings × 2 5 × 11 Bearing REPEAT THIS STEP fOR OPPOSITE SIDE HARDWARE USED Rear Wheel Hex Assembly (ACTUAL SIZE) × 2 Cross Pin 2 x SHIMS BETWEEN BEARING AND PIN ×...
  • Page 13 Shock Setup (Fluids Bag) × 4 1. Remove Springs 2. fill with oil 3. Bleed 4. Tighten 5. Replace Springs Visit prolineracing.com/pro-mt/build for shock assembly videos and spring rate charts. HARDWARE USED Install Front Shocks (ACTUAL SIZE) × 2 M3 × 16 BHCS...
  • Page 14 HARDWARE USED Servo Link (ACTUAL SIZE) 17mm (ACTUAL SIZE) Steering Rod × 2 Short Rod Ends × 2 Large Pivot Balls Remove Passenger Side Pod HARDWARE USED HARDWARE USED Install Servo (ACTUAL SIZE) (ACTUAL SIZE) × 2 Remove (4) screws in servo mount M3 ×...

  • Page 15: Motor Installation

    HARDWARE USED Motor Installation (ACTUAL SIZE) × 2 M3 × 8 SHCS × 2 Hd Motor Washer Remove HD Transmisison Cover Install Motor Set Gear Mesh (Pinion sold separately) Reinstall Gear Cover HARDWARE USED Electronics Placement (ACTUAL SIZE) SPEED CONTROLLER (Not Included) RECEIVER (Not Included) ANTENNA TUBE fOAM STRIPS...
  • Page 16 Paint body with Lexan/ polycarbonate safe paint Allow paint to dry completely Remove window masks and outer film Apply decals Ream body post holes on marked dimples Mount body to chassis using Secure-Loc Caps HARDWARE USED (ACTUAL SIZE) Congratulations! Enjoy your Pro-Line PRO-MT!
  • Page 17 6097-00 PRO-2 Front Clamping Hex (2) 6262-04 PRO-MT Rear Bumper 6098-00 PRO-2 Rear Clamping Hex (2) 6262-05 PRO-MT Rear Hub Carriers 6262-06 PRO-MT HD Sliding Axle Kit 6100-00 4mm Serrated Wheel Nuts (4) 6262-07 Drive Pins & Clips 1170-14 Trencher 2.8” on F-11 Wheels (2)

  • Page 18: Track Information

    Stock PRO-MT Setup TRACK: EVENT: DRIVER: DATE: MONSTER TRUCK SETUP SHEET QUAL: FINISH: FRONT PROTRAC SUSPENSION FRONT SHOCKS INSIDE (A) PISTON: Stock OIL WEIGHT: 45 wt CAMBER: ° (B) PRIMARY SPRING: Yellow ° TOE: (C) SECONDARY SPRING: Green RIDE HEIGHT:...
  • Page 19 TRACK: EVENT: DRIVER: DATE: MONSTER TRUCK SETUP SHEET QUAL: FINISH: FRONT PROTRAC SUSPENSION FRONT SHOCKS INSIDE (A) PISTON: OIL WEIGHT: CAMBER: ° (B) PRIMARY SPRING: ° TOE: (C) SECONDARY SPRING: RIDE HEIGHT: DROOP SPACER: COMPRESSION SPACER: (D) SPRING ADJUSTMENT: REAR PROTRAC SUSPENSION INSIDE REAR SHOCKS CAMBER:...