[Connection Lock]; [Off] - Panasonic PT-VZ575N Operating Instruction

[KEY1] - [KEY4]
[KEY]
[EAP]
[USE NAME]
[PASSWORD]
Note
f If you are unable to connect to the wireless LAN through the access point even after performing the steps in "Projector
Æ
settings" ( page 99), contact the manufacturer of the access point (Radio repeater).
f When using EAP, the projector needs to be set according to the setting of the RADIUS server. Check with the network
administrator for the setting of the RADIUS server.
f When using an EAP together with an access point with invalid SSID broadcast, select WPA-EAP or WPA2-EAP for the
authentication method even if the authentication method of the access point is [WPA-EAP] or [WPA2-EAP].
f If USER1 ~ 3 is used, you cannot connect to the access point of stealth SSID configuration, please use it to cancel the
stealth setting. For details, please refer to the Operating Instructions of the access point.
6) Press as to select [OK], and press the <ENTER> button.
r Default setting of [USER1], [USER2], [USER3]
f The following settings are set before the projector leaves the factory.

[CONNECTION LOCK]

Switches the network signal or chooses one fixed signal.
1) Press as to select [CONNECTION LOCK].
2) Press qw to switch the item.
f The items will switch each time you press the button.

[OFF]

[Panasonic APPLICATION] The [Panasonic APPLICATION] is the fixed [NETWORK/USB] input signal.
[Miracast]
[MEMORY VIEWER]
Note
f If [CONNECTION LOCK] is set to one fixed item other than [OFF] and you press other buttons, the [KEY NOT APPLICABLE]
appears.
Chapter 4 Settings - [NETWORK/USB] menu
Set a [WEP] key to the key number selected with [DEFAULT KEY].
It is can be set when [AUTHENTICATION] is [OPEN] or [SHARED] and [DEFAULT KEY]
is [WEP].
Either the 64-bit or 128-bit WEP key can be set. For the 64-bit key, input 5 alphanumerics
(or a 10-digit string for the hexadecimal format) for the 128-bit key, input 13
alphanumerics (or a 26-digit string for the hexadecimal format).
Set a key.
It is can be set when [AUTHENTICATION] is [WPA-PSK] or [WPA2-EAP].
Input either 8 to 63 alphanumerics or a 64 digit string in the hexadecimal format.
Select the EAP setup in the RADIUS server.
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-PSK] or
[WPA2-EAP].
Types of EAP that can be selected are as follows.
PEAP (MS-CHAPv2), PEAP (GTC), EAP-TTLS (MD5), EAP-TTLS (MS-CHAPv2 ),
EAP-FAST (MS-CHAPv2), EAP-FAST (GTC)
Input a user name used for authentication (excluding spaces) (maximum 64 characters).
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-PSK] or
[WPA2-EAP].
Input a password used for authentication (maximum 64 characters).
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-PSK] or
[WPA2-EAP].
[SSID]
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
[DEFAULT GATEWAY]
[AUTHENTICATION]
[ENCRYPTION]
[DNS1] / [DNS2]
The [NETWORK/USB] input signal can be switched between [Panasonic APPLICATION],
[Miracast] and [MEMORY VIEWER].
The [Miracast] is the fixed [NETWORK/USB] input signal.
The [MEMORY VIEWER] is the fixed [NETWORK/USB] input signal.
Panasonic Projector
OFF
192.168.11.100
255.255.255.0
192.168.11.1
OPEN
NULL
NULL
ENGLISH - 93