Panasonic PT-VX42Z Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Projector
  5. PT-VX42Z
  6. Manual
Panasonic PT-VX42Z Manual

Panasonic PT-VX42Z Manual

Lcd projector
Hide thumbs Also See for PT-VX42Z:
Table of Contents

Advertisement

Quick Links

Download this manual
As of October 2013. Specifications and appearance are subject to change without notice.
SFL13M010
S
P
E
PT-VX42Z
P ro d u c t N u m b e r :
LCD Projectors
P ro d u c t N a m e :
F
C
I
L
E
1 / 1 3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT-VX42Z and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Panasonic PT-VX42Z

Summary of Contents for Panasonic PT-VX42Z

  • Page 1 PT-VX42Z P ro d u c t N u m b e r : LCD Projectors P ro d u c t N a m e : As of October 2013. Specifications and appearance are subject to change without notice.

  • Page 2: Specifications

    PT-VX42Z LCD Projectors Specifications Main unit Power supply 100 –240 V AC, 50/60 Hz Power consumption 100–120 V: 300 W, 220–240 V: 280 W (0.4 W when Standby mode set to Eco* , 1.3 W when Standby mode set to Network, 9 W when Standby mode set to Normal)
  • Page 3 PT-VX42Z LCD Projectors COMPUTER (RGB) 2IN/ 1OUT D-sub HD 15-pin (female) × 1 R, G, B (input/output selectable using on-screen menu) G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms; B, R: 0.7 Vp-p, 75 ohms; HD/VD, SYNC: high impedance, TTL (positive/negative) NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
  • Page 4 PT-VX42Z LCD Projectors Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. (2-15/32) 176 (6-15/16) 352 (13-27/32) Terminals Computer 1 input Computer 2 input / computer 1 output HDMI input LAN connector Serial input Video input...

  • Page 5: Standard Setting-Up Position

    PT-VX42Z LCD Projectors Standard setting-up position NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and bracket ø38 assembly ET-PKV101B. (1-1/2) This illustration is not drawn to scale. Upper edge of projected image 129.5 125.5 (5-3/32) (4-15/16)

  • Page 6: Installable Angle

    PT-VX42Z LCD Projectors For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 4:3 minimum L (m) = (diagonal screen size in inches) × 0.0243 – 0.0294 maximum L (m) = (diagonal screen size in inches) × 0.0391 – 0.0319 NOTE: Distances calculated with the above equations will include a slight error.

  • Page 7: List Of Compatible Signals

    PT-VX42Z LCD Projectors List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 80 kHz (15 kHz to 100 kHz for RGB signals), vertical scanning frequencies of 50 Hz to 120 Hz (50 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum imum for RGB signals) can be input.
  • Page 8 PT-VX42Z LCD Projectors Display mode Display Scanning frequency Dot clock Format resolution frequency (dots)* (kHz) (kHz) (MHz) 1280 × 768 60.3 74.9 102.3 HDMI/RGB 1280 × 768 68.6 84.8 117.5 41.2 50.0 69.9 1280 × 800 1280 × 800 49.7 60.0...

  • Page 9: Serial Connector

    PT-VX42Z LCD Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names...

  • Page 10: Cable Specifications

    PT-VX42Z LCD Projectors Cable specifications Projector PC (DTE) Control commands < > r < > r Power on (standby mode on) – – Power off (standby mode off) – – Input signal selection IIS:<input si gnal> IIS:<input signal> – –...

  • Page 11: Status Request Commands

    HD1 = HDMI, RG1 = computer 1, RG2 = computer 2, NWP = network <input signal> PA1 = memory viewer, MG1 = panasonic application, MV1 = Miracast, VID = video, SVD = S-Video 000 = power off (standby mode off), 001 = power on (standby mode on) <power condition>...
  • Page 12 PT-VX42Z LCD Projectors Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating. Make sure there is the unobstructed space as shown below or more around the projector’s exhaust openings.

  • Page 13: Operating The Projector Continuously

    PT-VX42Z LCD Projectors Operating the projector continuously If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration becomes shorter. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less).

Table of Contents